Search Results

Search found 30206 results on 1209 pages for 'top partners 2010 awards'.

Page 681/1209 | < Previous Page | 677 678 679 680 681 682 683 684 685 686 687 688  | Next Page >

• How to wire 20 computers and 20 phones and 1 server into LAN?

  - by John Smith

  I have currently 3 switches Two Netgear JFS524 with 24 slots, One Belkin with 16 slots. Server DSL Internet Router. Main question is how to connect switches together, two Netgear's are next to each other, yet one is about 100 feet away and holds about 5 computer and 5 phones. If i connect them with only 1 wire will that limit bandwidth? e.g. all 23 computers will be limited to speed of one CAT5e cable? If i connect switches with 2 cables will this give speed boost? What's the ideal scenario should i just move the third switch next to other two? Will the speed of computer connected to white switch be same as computer connected to top switch? Will moving white switch right next top switch and having 16 wires comming 100 feet instead of 1 wire comming 100 feet make it faster? EDIT 1: I actually have NETGEAR ProSafe GS105 Gigabit switch its only has 4 ports in it though, you think i can have use of it in current setup? Like connect all 3 switches and server into it and keep internet router and phone server on one of the slower switches EDIT 2: Everyone mention gigabit switches, but will they do any difference with 10/100 network cards? I then have to use gigabit cards in every computer too? I could in server perhaps, but users will be 10/100

  Read the article

• snort analysis of wireshark capture

  - by Ben Voigt

  I'm trying to identify trouble users on our network. ntop identifies high traffic and high connection users, but malware doesn't always need high bandwidth to really mess things up. So I am trying to do offline analysis with snort (don't want to burden the router with inline analysis of 20 Mbps traffic). Apparently snort provides a -r option for this purpose, but I can't get the analysis to run. The analysis system is gentoo, amd64, in case that makes any difference. I've already used oinkmaster to download the latest IDS signatures. But when I try to run snort, I keep getting the following error: % snort -V ,,_ -*> Snort! <*- o" )~ Version 2.9.0.3 IPv6 GRE (Build 98) x86_64-linux '''' By Martin Roesch & The Snort Team: http://www.snort.org/snort/snort-team Copyright (C) 1998-2010 Sourcefire, Inc., et al. Using libpcap version 1.1.1 Using PCRE version: 8.11 2010-12-10 Using ZLIB version: 1.2.5 %> snort -v -r jan21-for-snort.cap -c /etc/snort/snort.conf -l ~/snortlog/ (snip) 273 out of 1024 flowbits in use. [ Port Based Pattern Matching Memory ] +- [ Aho-Corasick Summary ] ------------------------------------- | Storage Format : Full-Q | Finite Automaton : DFA | Alphabet Size : 256 Chars | Sizeof State : Variable (1,2,4 bytes) | Instances : 314 | 1 byte states : 304 | 2 byte states : 10 | 4 byte states : 0 | Characters : 69371 | States : 58631 | Transitions : 3471623 | State Density : 23.1% | Patterns : 3020 | Match States : 2934 | Memory (MB) : 29.66 | Patterns : 0.36 | Match Lists : 0.77 | DFA | 1 byte states : 1.37 | 2 byte states : 26.59 | 4 byte states : 0.00 +---------------------------------------------------------------- [ Number of patterns truncated to 20 bytes: 563 ] ERROR: Can't find pcap DAQ! Fatal Error, Quitting.. net-libs/daq is installed, but I don't even want to capture traffic, I just want to process the capture file. What configuration options should I be setting/unsetting in order to do offline analysis instead of real-time capture?

  Read the article

• Intel DriverInstall issue on HP ProLiant server DL580G5

  - by TomTom

  Given: A HP ProLiant server to be used for Hyper-V server (R 2) Problem: The server has a HP NC364T quad port card, which actually is an Intel 1000 Pro adapter. We are stuck getting this adapter properly working. We need to get it working with: 2 trunks of 2 ports each one of them fully vlan "aware" (without filtering anything - so that Hyper-V can do the VLAN filtering). So far we did: Install the server Install latest PSP. Problem here - tool does not work to set up teaming. We tried to install the latest ProWin pack from Intel - the drivers there are a LOT more current (26th of Marrch 2010, 9.13.41.0). The intalled driver (Microsoft) is ancient (march 2009, 9.13.4.10) A driver update fails both on command line (pnputil) as well as the PortLock device manager executable. No informatoin is provided. the ANS toolset can not create teams (fails with error - again, no reason provided), I know of no logs and the event log has no information either. Questions: What are the best drivers to use? How do we actually install them? How can we then set up teaming and how do we set up the VLAN behavior wanted?

  Read the article

• Unable to login to Amazon EC2 compute server

  - by MasterGaurav

  I am unable to login to the EC2 server. Here's the log of the connection-attempt: $ ssh -v -i ec2-key-incoleg-x002.pem [email protected] OpenSSH_5.6p1, OpenSSL 0.9.8p 16 Nov 2010 debug1: Reading configuration data /home/gvaish/.ssh/config debug1: Applying options for * debug1: Connecting to ec2-50-16-0-207.compute-1.amazonaws.com [50.16.0.207] port 22. debug1: Connection established. debug1: identity file ec2-key-incoleg-x002.pem type -1 debug1: identity file ec2-key-incoleg-x002.pem-cert type -1 debug1: identity file /home/gvaish/.ssh/id_rsa type -1 debug1: identity file /home/gvaish/.ssh/id_rsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3 debug1: match: OpenSSH_5.3 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.6 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'ec2-50-16-0-207.compute-1.amazonaws.com' is known and matches the RSA host key. debug1: Found key in /home/gvaish/.ssh/known_hosts:8 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: ec2-key-incoleg-x002.pem debug1: read PEM private key done: type RSA debug1: Authentications that can continue: publickey debug1: Trying private key: /home/gvaish/.ssh/id_rsa debug1: No more authentication methods to try. Permission denied (publickey). What can be the possible reason? How do I fix the issue?

  Read the article

• Use to host email for a domain name that wasn't our primary domain name

  - by drpcken

  Exchange 2007 on an Server 2003 active directory. My primary domain (MyMainDomain.com) controller also hosts dns and dhcp. I have a secondary domain name (MySecondDomain.net) that my Exchange Server allows emails from. It wasn't a physical domain, just accepted by exchange and setup as the Active Directory user's main smtp and outgoing address. Its MX records point to MyMainDomain.com's public exchange address. I've taken MySecondDomain.net and move the mail boxes to a hosted exchange 2010 environment. MX records now point to this new exchange system and when I send and email OUTSIDE the MyMainDomain.com environment (say gmail) it works and sends to the hosted exchange setup for MySecondDomain.net. however when I send an email from a user on MyMainDomain.com, it goes to the old exchange 2007 server I am hosting internally. I have removed MySecondDomain.net from the allowed domains, removed the DNS zone for MySecondDomain.net, and cleared DNS cache. I was convinced it was my internal dns server but I've cleared the DNS cache. Is there something I'm missing somewhere in exchange 2007? Or is it my domain controller/dns? Sorry if this is confusing. Thank you!

  Read the article

• saslauthd using too much memory

  - by Brian Armstrong

  Woke up today to see my site slow/unresponsive. Pulled up top and it looks like a ton of saslauthd processes have spun up using about 64m of RAM each, causing the machine to enter swap space. I've never seen this many used on there. top - 16:54:13 up 85 days, 11:48, 1 user, load average: 0.32, 0.50, 0.38 Tasks: 143 total, 1 running, 142 sleeping, 0 stopped, 0 zombie Cpu(s): 0.7%us, 0.3%sy, 0.0%ni, 97.3%id, 0.2%wa, 0.0%hi, 0.0%si, 1.4%st Mem: 1048796k total, 1025904k used, 22892k free, 14032k buffers Swap: 2097144k total, 332460k used, 1764684k free, 194348k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 848 admin 20 0 263m 115m 4840 S 0 11.3 5:02.91 ruby 906 admin 20 0 265m 113m 4828 S 0 11.1 5:37.24 ruby 30484 admin 20 0 248m 91m 4256 S 6 9.0 219:02.30 delayed_job 4075 root 20 0 160m 65m 952 S 0 6.4 0:24.22 saslauthd 4080 root 20 0 162m 64m 936 S 0 6.3 0:24.48 saslauthd 4079 root 20 0 162m 64m 936 S 0 6.3 0:24.70 saslauthd 4078 root 20 0 164m 63m 936 S 0 6.2 0:24.66 saslauthd 4077 root 20 0 163m 62m 936 S 0 6.1 0:24.66 saslauthd 3718 mysql 20 0 312m 52m 3588 S 1 5.1 3499:40 mysqld 699 root 20 0 72744 7640 2164 S 0 0.7 0:00.50 ruby 15701 postfix 20 0 106m 5712 4164 S 1 0.5 0:00.50 smtpd 15702 postfix 20 0 52444 3252 2452 S 1 0.3 0:00.06 cleanup 4062 postfix 20 0 41884 3104 1788 S 0 0.3 125:26.01 qmgr 15683 root 20 0 51504 2780 2180 S 0 0.3 0:00.04 sshd 14595 postfix 20 0 52308 2548 2304 S 1 0.2 0:24.60 proxymap 15483 postfix 20 0 43380 2544 1992 S 0 0.2 0:00.38 smtp 15486 postfix 20 0 43380 2544 1992 S 0 0.2 0:00.36 smtp 15488 postfix 20 0 43380 2540 1992 S 0 0.2 0:00.38 smtp 15485 postfix 20 0 43380 2532 1984 S 0 0.2 0:00.36 smtp 15489 postfix 20 0 43380 2532 1984 S 0 0.2 0:00.40 smtp Wasn't sure what Saslauthd is, Google says it handles plantext authentication. The machine has been sending a lot of email through postfix, so this could be related. Anyone know why so many may have spun up? Are they safe to kill? Thanks!

  Read the article

• Is Windows Server 2008R2 NAP solution for NAC (endpoint security) valuable enough to be worth the hassles?

  - by Warren P

  I'm learning about Windows Server 2008 R2's NAP features. I understand what network access control (NAC) is and what role NAP plays in that, but I would like to know what limitations and problems it has, that people wish they knew before they rolled it out. Secondly, I'd like to know if anyone has had success rolling it out in a mid-size (multi-city corporate network with around 15 servers, 200 desktops) environment with most (99%) Windows XP SP3 and newer Windows clients (Vista, and Win7). Did it work with your anti-virus? (I'm guessing NAP works well with the big name anti-virus products, but we're using Trend micro.). Let's assume that the servers are all Windows Server 2008 R2. Our VPNs are cisco stuff, and have their own NAC features. Has NAP actually benefitted your organization, and was it wise to roll it out, or is it yet another in the long list of things that Windows Server 2008 R2 does, but that if you do move your servers up to it, you're probably not going to want to use. In what particular ways might the built-in NAP solution be the best one, and in what particular ways might no solution at all (the status quo pre-NAP) or a third-party endpoint security or NAC solution be considered a better fit? I found an article where a panel of security experts in 2007 say NAC is maybe "not worth it". Are things better now in 2010 with Win Server 2008 R2?

  Read the article

• Controller Error: Do I need to worry?

  - by Kryten

  Hi, I have a HP Pavillion dv5224ea Laptop with Windows 7 on it. Recently I discovered a Error in Event Viewer: The driver detected a controller error on \Device\Ide\IdePort1. (more details): - System - Provider [ Name] atapi - EventID 11 [ Qualifiers] 49156 Level 2 Task 0 Keywords 0x80000000000000 - TimeCreated [ SystemTime] 2010-03-07T12:43:07.090197600Z EventRecordID 30198 Channel System Computer Alistair-Win7 Security - EventData \Device\Ide\IdePort1 0000100001000000000000000B0004C002000000850100C00000000000000000000000000000000000000000000000000000000004100000 -------------------------------------------------------------------------------- Binary data: In Words 0000: 00100000 00000001 00000000 C004000B 0008: 00000002 C0000185 00000000 00000000 0010: 00000000 00000000 00000000 00000000 0018: 00000000 00001004 In Bytes 0000: 00 00 10 00 01 00 00 00 ........ 0008: 00 00 00 00 0B 00 04 C0 .......À 0010: 02 00 00 00 85 01 00 C0 ......À 0018: 00 00 00 00 00 00 00 00 ........ 0020: 00 00 00 00 00 00 00 00 ........ 0028: 00 00 00 00 00 00 00 00 ........ 0030: 00 00 00 00 04 10 00 00 ........ Event Viewer is recording A LOT of these errors (sometimes 13, one after the other!). Do I need to worry? What does this error mean? What device could "\Device\Ide\IdePort1" be? What is a ATAPI Error? Do I need to re-install Windows? I generally find the occurs when I try to backup my machine (using Windows Backup) or when using a program that uses Volume Shadow Copy. I have run "sfc", no problems. There are no Device Errors in Device Manager. I have also run "vssadmin list writers", no problems. Whats going on??? Would it be a good idea to re-install Windows 7?

  Read the article

• OS X can't copy files from Windows Home Server...over wifi.

  - by John Clayton

  I'm a brand spanking new user of OS X, coming from a lifetime of Windows use. I've been setting up my new Macbook Pro and have run into a very unusual problem. Over wifi, I am unable to copy files to or from my Windows Home Server. The problem seems to exist only over wifi, and only to WHS. Here are the details of my setup: 2010 Macbook Pro (Core i7), OS X 10.6.3 Windows Home Server PP3 (virtualized in XenServer 5.5) Windows 7 Ultimate x64 desktop Windows 7 Ultimate x64 in Boot Camp D-Link DIR-655 wireless N router Here is what I've done to narrow down the problem: Files copy fine from WHS to OS X when using gigabit ethernet Files copy fine from desktop to OS X when using gigabit ethernet Files fail to copy from WHS to OS X when using wifi (error -51) Files copy fine from desktop to OS X when using wifi Files copy fine from WHS to Boot Camp when using wifi Files copy fine from desktop to Boot Camp when using wifi From what I can tell, it seems to be some sort of issue between OS X and WHS, but I can't for the life of me see what would be different between shares on WHS and my desktop. They are both connected using smb://ADDRESS (I've tried both by IP and name). I can browse the shares on the WHS, but copying to OS X fails. I originally found the issue while installing VS2010 off an ISO from WHS, mounted to a Windows 7 VM using VMware Fusion. During the installation the VM was unusable - even the clock got behind the host be about 8 minutes. Once I plugged in the ethernet and disabled the wifi things picked up and finished quickly. The Fusion 3.1 RC is the only I think of that I installed that may have messed with the wifi driver. I've also tried resetting the wifi router, and have changed it from being G & N to N-only. Under Boot Camp I get similar speeds as my wife's N laptop. Any ideas? Thanks!

  Read the article

• Alfresco Community Edition Consultants

  - by Talkincat

  I am in the process of putting together an document management system based on Alfresco Community 3.2r2. Because Alfresco will not allow its partners to work with the Community edition, I have found it devilishly tricky to find consultants that specialize in Alfresco to help me with this project. Can anyone point me in the direction of someone that can help me get this system up an running? I will mostly need help with integrating Alfresco with Active Directory (LDAP passthrough, user/group sync and SSO) and performance tuning the system. Any help is greatly appreciated.

  Read the article

• Can't reset Windows 7 Registry permissions.

  - by n10i

  hi all, i am trying to reset win 7 registry permissions using secedit /configure /cfg %windir%\inf\defltbase.inf /db defltbase.sdb /verbose /areas REGKEYS But i am receiving the following error: An extended error has occurred. The task has completed with an error. See log %windir%\security\logs\scesrv.log for detail info. The content Of the log file: ------------------------------------------- Friday, April 16, 2010 1:50:43 PM ----Configuration engine was initialized successfully.---- ----Reading Configuration Template info... ----Configure 64-bit Registry Keys... Configure users.default. Warning 5: Access is denied. Error taking ownership of users.default\software\SetID. Warning 5: Access is denied. Error opening users.default\software\SetID. Warning 5: Access is denied. Error setting security on users.default\software\SetID. Configure machine\software. Warning 5: Access is denied. Error setting security on machine\software. Warning 1336: The access control list (ACL) structure is invalid. Error setting security on machine\software\Macrovision. Configuration of Registry Keys was completed with one or more errors. ----Configure 32-bit Registry Keys... Configure machine\software. Warning 1336: The access control list (ACL) structure is invalid. Error setting security on machine\software\Audible. Configuration of Registry Keys was completed with one or more errors. ----Un-initialize configuration engine... plz! help me guys!

  Read the article

• Debian amd64 on Dell Studio 540 reboot hangs

  - by Shcheklein

  Hi, I have Dell Studio 540 desktop and Debian Lenny installed on it: 2.6.26-2-amd64 #1 SMP Tue Mar 9 22:29:32 UTC 2010 x86_64 GNU/Linux The problem is that I can't reboot it. It just hangs after "Will now restart" message. I've already tried: reboot=b, reboot=a, reboot=h kernel options. Nothing helps. Additional info (I can provide any other information): dmidecode System Information Manufacturer: Dell Inc. Product Name: Studio 540 lspci 00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03) 00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 1 00:1c.2 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 3 00:1c.5 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 6 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller 02:00.0 FireWire (IEEE 1394): JMicron Technologies, Inc. Device 2380 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)

  Read the article

• Request bursting from web application Load Tests

  - by MaseBase

  I'm migrating our web and database hosting to a new environment on all new machines. I've recently performed a Load Test using WAPT to generate load from multiple distributed clients. The server has plenty of room to handle the traffic load, but I'm seeing an odd pattern of incoming traffic during the load tests. Here is the gist of our setup: Firewall server running MS Forefront TMG 2010 on Win 2k8 server Request routing done by IIS Application Request Routing on firewall machine Web server is a Hyper-V VM on the Database server (which is the host OS) These machines are hefty with dual-CPU's with six cores (12 total procs) Web server running IIS 7.5 Web applications built in ASP.NET 2.0, with 1 ISAPI filter (Url Rewrite) in front What I'm seeing during the load tests is that the requests all come through in bursts. Even though I have 7 different distributed clients sending traffic loads, the requests come through about 300-500 requests at a time. The performance monitor shows nearly all of the counters moving through this pattern, where a burst of requests comes in the req/sec jumps to 70, the queued requests jumps to 500, the current requests jumps up, the CPU jumps up, everything. Then once it's handled that group of requests, it has a lull for nearly 10 seconds where nearly nothing is happening. 0-5 req/sec, 0 queued requests, minimal CPU usage. Then after 10 seconds of inactivity, another burst comes through, spiking all of the counters once again. What I can't figure out is why the requests are coming through in bursts when I know that the load being generated is not sent that way, especially considering the various load-generating clients sending traffic all in different intervals with random think time's between each request. Is there something in the layers between Hyper-V or perhaps in the hardware which might cause this coalesce of requests together? Here is what i'm looking at, the highlighted metric is Requests/sec, but the others critical counter go with it: Requests Queued (which I'd obviously like to keep as close to 0 as possible). Any ideas on this?

  Read the article

• Windows 7 Black Screen On Boot, Seperate Bootable VHD Works Fine

  - by David Osborn

  I have a Window 7 x64 install with a bootable VHD (also Windows 7 x64). I was having problems getting my homeserver to do backups (VSS erred) so I ran check disk and used a tool from MS (cleanc2r.exe) to remove an empty Q drive from the VHD that I believe was a result of installing Office 2010 Beta. (All of this was done on the bootable VHD, not the main install.) Now I can't boot into the main install. It gets past the Starting Windows screen and then goes black. I can still boot into the bootable VHD and everything works fine from there. I have tried to boot the main install in Safe Mode/Safe Mode with Networking/and Safe Mode command prompt and it has the same issue. I ran chkdsk /r on the main install and after doing all the work there was a message about correcting some free space that was marked as allocated and also that it was unable to make an entry into the event log. I tried the startup repair utility and it found no problems. I don't see the setting for restore to last know good configuration so I couldn't do that. I don't recall installing anything new to the main install nor having hooked up any new hardware recently.

  Read the article

• Macbook Pro Triple Boot OS X Lion, Windows 7 and Windows 8

  - by Lloyd Sparkes

  MacBook Pro (Summer 2010 Model, Basic Model) I currently have OS X Lion and Windows 7 running side by side on my MacBook Pro. However I have a need to get Windows 8 running as well in this mix (a Virtual Machine is not good enough, I need the performance). I have created a suitably sized parition (80GB) that is recognizable in Boot Camp. However every time I try to boot from the USB stick (that worked to install Windows 8 on my PC) using the latest version of rEFIt, it just boots Windows 7 and not the Windows 8 installer. I cannot start the installation within Windows 7 as it will just install over Windows 7. I'm guessing the Boot Camp emulation is doing something werid to stop the "Press any key to install Windows..." message from appearing (which should happen if the installer detects Windows is already installed (e.g. if you left your install disk in). Is there a way to get around this / force the installer to start? (Note I cannot start the Windows 7 installer either if I wanted to install a second copy of Windows 7 to upgrade to Windows 8)

  Read the article

• 1GB cached memory - Do I need more RAM?

  - by Martin

  The server runs well but I wonder if I should get more RAM. I only have a few MB of "free" memory and 1.2GB of "cached" memory: free: total used free shared buffers cached Mem: 3945 3893 51 0 28 1216 -/+ buffers/cache: 2648 1296 Swap: 3895 857 3038 I learned that cached memory is used while it's free and not. Is the cached value an indicator for the need of more RAM? cat /proc/meminfo 1 day after flushing the cache: MemTotal: 4040048 kB MemFree: 32844 kB Buffers: 18956 kB Cached: 1249092 kB SwapCached: 161576 kB Active: 3611328 kB Inactive: 189104 kB SwapTotal: 3989496 kB SwapFree: 2894200 kB Dirty: 20520 kB Writeback: 0 kB AnonPages: 2523496 kB Mapped: 217744 kB Slab: 70940 kB SReclaimable: 36756 kB SUnreclaim: 34184 kB PageTables: 99648 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 6009520 kB Committed_AS: 6401716 kB VmallocTotal: 34359738367 kB VmallocUsed: 18852 kB VmallocChunk: 34359719439 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB top: top - 17:20:10 up 112 days, 3:06, 1 user, load average: 1.01, 1.62, 1.48 Tasks: 208 total, 1 running, 207 sleeping, 0 stopped, 0 zombie Cpu(s): 0.6%us, 0.6%sy, 0.0%ni, 97.5%id, 1.3%wa, 0.0%hi, 0.1%si, 0.0%st Mem: 4040048k total, 3953108k used, 86940k free, 16348k buffers Swap: 3989496k total, 1095712k used, 2893784k free, 1235436k cached

  Read the article

• Apache mod_auth_kerb asking 2 authentication

  - by Rianto Wahyudi

  I've configured Apache to use mod_auth_kerberos. So far everything is working nicely for client thats connected to Active Directory and have their browser to ntlm enabled. When clients are not in the domain or the browser configurerd not to authenticate automatically, they are being prompted by 2 login prompt. The first login prompt is blank and the second one is the oen that we configured First Login prompt: http://www.screencast.com/t/ZGNlZTQwZm Second Login prompt : http://www.screencast.com/t/MDA2N2Fl From the log ( first authentication) : [Wed Jan 06 15:47:29 2010] [debug] src/mod_auth_kerb.c(1684): [client x.x.x.x] [pid 2562] kerb_authenticate_user entered with user (NULL) and auth_type Kerberos In the first loging prompt , I can put any text for username and password. Once the first login form submited, it will ask for the 2nd login prompt. Apache have following config : <Directory /web/apache2/htdocs> AllowOverride All AuthType Kerberos AuthName "Staff Access ONLY Kerb-Auth" KrbAuthRealms EXAMPLE.COM Krb5Keytab /etc/httpd/conf.d/example.ktab Allow from localhost Require valid-user <Directory> What could be the cause of the first authentication and how can I get rid of them ?

  Read the article

• ssh connection slow when using @hostname.com but now when using @ipaddress

  - by Alex Recarey

  When connecting to a Debian server using ssh, if I use [email protected] (the IP address of hte server) the connection is instant. If however I use [email protected] (a DNS redirected to the IP address of the server) the ssh connection hangs for a 20 seconds before connecting successfully. The ssh logs show the following: [alex@alex home]$ ssh -v -v [email protected] OpenSSH_5.5p1, OpenSSL 1.0.0c-fips 2 Dec 2010 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 and here it hangs during 20 seconds before continuing. I think it might have something to do with reverse DNS or similar (the server does not really "know" it's name is hostname.com, it just has that DNS rediriected to its IP address). I have added the following options to /etc/ssh/sshd_config: UseDNS no GSSAPIAuthentication no to no effect. The server's DNS records in /etc/resolv.conf are configured correctly: ping hostname.com PING sub.domain.com (X.X.X.X) 56(84) bytes of data. 64 bytes from replicant (X.X.X.X): icmp_seq=1 ttl=64 time=0.029 ms 64 bytes from replicant (X.X.X.X): icmp_seq=2 ttl=64 time=0.050 ms?s Thanks for the help. Solution: It seems the DSL router my ISP saddled me with was causing the trouble. Changing my DNS server from 192.168.1.1 (router's IP) to google's (8.8.8.8, always good to know when you are in a hurry) instantly solved the connection delay problem. I am guessing that the 50€ router provided does not cache DNS entries, although I don't understand why pinging the DNS address had no delay, and 20 seconds is too long of a wait, even for uncached DNS. Tnanks again for the help!

  Read the article

• 403 Forbidden when Deploying asp.net 4.0 site to IIS 7

  - by Jordan

  So I have an EC2 instance running, the URL NoWeatherSurprises.com I have the DNS pointing there, and I set up a new site in IIS 7 and pointed it to a folder. I used Visual Studios Web Developer 2010 express to publish to this folder. It now has the binaries and such. However if I go to NoWeatherSurprises.com I get the welcome to IIS 7 screen. I'd expect to go to my application If I navigate to http://noweathersurprises.com/weather/ [weather was the folder I published to under wwwroot] I get a 403 forbidden. I have no idea why, I am guessing that it is trying to do a directory listing or something instead of launching my MVC Application. So 2 problems in summary. It is not pointing the domain to the folder directly and I need to add /weather I am getting a 403 forbidden instead of the results of my home controller with the index action. I am new to IIS 7, I had been using IIS 6 and had a lot less trouble setting it up, but I suspect that's my own fault and i am just missing something. Thanks in advance for any help

  Read the article

• Redis 2.0.3 would not let go of deleted appendonly.aof file after BGREWRITEAOF

  - by Alexander Gladysh

  Ubuntu 10.04.2, Redis 2.0.3 (more details at the end of the question). My AOF file for Redis is getting too large, to the point where it soon would threaten to take whole free disk space on my small-HDD VPS box: $ df -h Filesystem Size Used Avail Use% Mounted on /dev/xvda 32G 24G 6.7G 78% / $ ls -la total 3866688 drwxr-xr-x 2 redis redis 4096 2011-03-02 00:11 . drwxr-xr-x 29 root root 4096 2011-01-24 15:58 .. -rw-r----- 1 redis redis 3923246988 2011-03-02 00:14 appendonly.aof -rw-rw---- 1 redis redis 32356467 2011-03-02 00:11 dump.rdb When I run BGREWRITEAOF, the AOF file shrinks, but disk space is not freed: $ ls -la total 95440 drwxr-xr-x 2 redis redis 4096 2011-03-02 00:17 . drwxr-xr-x 29 root root 4096 2011-01-24 15:58 .. -rw-rw---- 1 redis redis 65137639 2011-03-02 00:17 appendonly.aof -rw-rw---- 1 redis redis 32476167 2011-03-02 00:17 dump.rdb $ df -h Filesystem Size Used Avail Use% Mounted on /dev/xvda 32G 24G 6.7G 78% / Sure enough, Redis is still holding the deleted file: $ sudo lsof -p6916 COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME ... redis-ser 6916 redis 7r REG 202,0 3923957317 918129 /var/lib/redis/appendonly.aof (deleted) ... redis-ser 6916 redis 10w REG 202,0 66952615 917507 /var/lib/redis/appendonly.aof ... How can I workaround this issue? I can restart Redis this time, but I would really like to avoid doing this on a regular basis. Note that I can not upgrade to 2.2 (upgrade to 2.0.4 is feasible though). More information on my system: $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 10.04.2 LTS Release: 10.04 Codename: lucid $ uname -a Linux my.box 2.6.32.16-linode28 #1 SMP Sun Jul 25 21:32:42 UTC 2010 i686 GNU/Linux $ redis-cli info redis_version:2.0.3 redis_git_sha1:00000000 redis_git_dirty:0 arch_bits:32 multiplexing_api:epoll process_id:6916 uptime_in_seconds:632728 uptime_in_days:7 connected_clients:2 connected_slaves:0 blocked_clients:0 used_memory:65714632 used_memory_human:62.67M changes_since_last_save:8398 bgsave_in_progress:0 last_save_time:1299014574 bgrewriteaof_in_progress:0 total_connections_received:17 total_commands_processed:55748609 expired_keys:0 hash_max_zipmap_entries:64 hash_max_zipmap_value:512 pubsub_channels:0 pubsub_patterns:0 vm_enabled:0 role:master db0:keys=1,expires=0 db1:keys=18,expires=0

  Read the article

• OS X random, jumpy dragging behavior

  - by Chris

  This problem has been going on since I got 10.7, and is persisting or even getting worse since I updated to Mavricks. The best way to describe it is thru an example- Let's say I'm working in Safari. Everything is working fine. Then, I'll switch to another app by clicking on it's window, for example, I'll click on Messages to shoot back a reply. When I click back to Safari, keyboard and mouse inputs don't work! The only way I can regain control of the app (Safari) is by clicking on the apps top bar, which then causes the app to jump left or right. If I'm in Messages and I switch back to Safari by clicking said top bar, it works fine. Same with switching back and forth using command-tab. I've narrowed the problem down to this - the first app (Safari, in this example) is, for some reason, deciding that I'm in the process of dragging the window around. This could be just an oddly persistent glitch in my system, but has anyone else seen this before? Perhaps a misplaced default write... somewhere along the line? Update A PRAM reset did absolutely nothing

  Read the article

• How do I export address book from N97

  - by mplungjan

  Hi, I need to copy my numbers from my private Nokia to my office BB. I have not found a way to export my phone numbers from ovi or elsewhere. On Mac iSync stopped working with snow leopard and OVI on windows does not export. I do not mind using a windows suggestion. I lost a description on how to use the ovi backup files in another program. What I have done so far terminal: sudo open -a iSync.app - it launched but iSync said "this device is not supported by iSync" went here http://europe.nokia.com/support/product-support/isync/compatibility-and-download found a plugin (I am sure that was not there a while ago :| ) Checked software version 22.0.110 installed plugin Ran iSync which found and installed my N97 device successfully. synced. It stopped with The connection was lost while talking to the phone. http://discussions.europe.nokia.com/t5/Nseries-and-S60-Smartphones/N97-iSync-Multimedia-Transfer-Modem/m-p/568560 no news since Jan 2010. Tried to download and install http://best-vcard.en.softonic.com/symbian but the installer fails :( I simply do not understand why Nokia is giving us such a hard time. I would not have considered switching from Nokia if Mac had been better supported. It is so frustrating that they just seem not to care losing Nokia fanbois like me - especially since I am this outspoken on the net and what i say on popular forums gets indexed by google fast. I am very close to just go iPhone here. Hope someone has Nokia's ears UPDATE: I Downloaded NbuExplorer from sourceforge. It will extract everything from an OVI backup into VCF, VCS and VMG files. Very useful software and free.

  Read the article

• Nginx + uWSGI + Django performance stuck on 100rq/s

  - by dancio

  I have configured Nginx with uWSGI and Django on CentOS 6 x64 (3.06GHz i3 540, 4GB), which should easily handle 2500 rq/s but when I run ab test ( ab -n 1000 -c 100 ) performance stops at 92 - 100 rq/s. Nginx: user nginx; worker_processes 2; events { worker_connections 2048; use epoll; } uWSGI: Emperor /usr/sbin/uwsgi --master --no-orphans --pythonpath /var/python --emperor /var/python/*/uwsgi.ini [uwsgi] socket = 127.0.0.2:3031 master = true processes = 5 env = DJANGO_SETTINGS_MODULE=x.settings env = HTTPS=on module = django.core.handlers.wsgi:WSGIHandler() disable-logging = true catch-exceptions = false post-buffering = 8192 harakiri = 30 harakiri-verbose = true vacuum = true listen = 500 optimize = 2 sysclt changes: # Increase TCP max buffer size setable using setsockopt() net.ipv4.tcp_rmem = 4096 87380 8388608 net.ipv4.tcp_wmem = 4096 87380 8388608 net.core.rmem_max = 8388608 net.core.wmem_max = 8388608 net.core.netdev_max_backlog = 5000 net.ipv4.tcp_max_syn_backlog = 5000 net.ipv4.tcp_window_scaling = 1 net.core.somaxconn = 2048 # Avoid a smurf attack net.ipv4.icmp_echo_ignore_broadcasts = 1 # Optimization for port usefor LBs # Increase system file descriptor limit fs.file-max = 65535 I did sysctl -p to enable changes. Idle server info: top - 13:34:58 up 102 days, 18:35, 1 user, load average: 0.00, 0.00, 0.00 Tasks: 118 total, 1 running, 117 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 3983068k total, 2125088k used, 1857980k free, 262528k buffers Swap: 2104504k total, 0k used, 2104504k free, 606996k cached free -m total used free shared buffers cached Mem: 3889 2075 1814 0 256 592 -/+ buffers/cache: 1226 2663 Swap: 2055 0 2055 **During the test:** top - 13:45:21 up 102 days, 18:46, 1 user, load average: 3.73, 1.51, 0.58 Tasks: 122 total, 8 running, 114 sleeping, 0 stopped, 0 zombie Cpu(s): 93.5%us, 5.2%sy, 0.0%ni, 0.2%id, 0.0%wa, 0.1%hi, 1.1%si, 0.0%st Mem: 3983068k total, 2127564k used, 1855504k free, 262580k buffers Swap: 2104504k total, 0k used, 2104504k free, 608760k cached free -m total used free shared buffers cached Mem: 3889 2125 1763 0 256 595 -/+ buffers/cache: 1274 2615 Swap: 2055 0 2055 iotop 30141 be/4 nginx 0.00 B/s 7.78 K/s 0.00 % 0.00 % nginx: wo~er process Where is the bottleneck ? Or what am I doing wrong ?

  Read the article

• Acronis Disk Director AFTER Clone Disk error: PXE-E61: Media test failure, check cable

  - by Kairan

  Used Acronis Disk Director on my desktop, plugged in the laptop drive 240GB SSD (USB) and the new hard drive 500GB SSD (usb) and the copy seemed to be fine. I didnt see any error messages but I didnt stare at it for 3 hours either. The clone disk of course the Toshiba hidden restore partition, the primary partition C drive and the active (boot?) partition and yes, did check box for copy NT signature. The computer boots up fine most of the time, but it seems that when the computer goes to sleep (i believe its sleep, hard to do much testing during school) or hibernate or reboot it will sometimes display this message: Intel(R) Boot Agent GE v1.3.52 Copyright (C) 1997-2010, Intel Corporation PXE-E61: Media test failure, check cable PXE-M0F: Exiting Intel Boot Agent Insert system disk in drive. Press any key when ready... Of course any key does nothing but repeat a similar method. However, if I press the power button on the laptop (Toshiba Portege R705, Win 7 Pro 64-bit) it puts computer into hibernate. After hibernating I press power button again and it comes out of hibernation without any odd messages or problems described above... so apparently that is my TEMP fix. Another recent issue I noticed is on occasion when creating a new folder or modifying something in the system variables, other random areas I will get a message: "The Stub received bad data" and simply retry the task and it works. Perhaps these two issues are linked.

  Read the article

• Different versions of iperf for windows give totally different results

  - by Albert Mata

  Measuring TCP output from a Windows client to Solaris server: WXP SP3 with iperf 1.7.0 -- returns an average around 90Mbit Same client, same server but iperf 2.0.5 for windows -- returns an average of 8.5 Mbit Similar discrepancies have been observed connecting to other servers (W2008, W2003) It's difficult to get to some conclusions when different versions of the same tool provide vastly different results. Example below: C:\tempiperf -v (from iperf.fr) iperf version 2.0.5 (08 Jul 2010) pthreads C:\tempiperf -c solaris10 Client connecting to solaris10, TCP port 5001 TCP window size: 64.0 KByte (default) [ 3] local 10.172.181.159 port 2124 connected with 10.172.180.209 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.2 sec 10.6 MBytes 8.74 Mbits/sec Abysmal perfomance, but now I test from the same host (Windows XP SP3 32bit and 100Mbit) to the same server (Solaris 10/sparc 64bit and 1Gbit running iperf 2.0.5 with default window of 48k) with the old iperf C:\temp1iperf -v iperf version 1.7.0 (13 Mar 2003) win32 threads C:\temp1iperf.exe -c solaris10 -w64k Client connecting to solaris10, TCP port 5001 TCP window size: 64.0 KByte [1208] local 10.172.181.159 port 2128 connected with 10.172.180.209 port 5001 [ ID] Interval Transfer Bandwidth [1208] 0.0-10.0 sec 112 MBytes 94.0 Mbits/sec So one iperf with a 64k window says 8.75Mbit and the old iperf with the same window size says 94.0Mbit. These results are constant through repeated tests. From my testing launching iperf(old) with window size "x" and iperf(new) with window size "x" instead of producing the same or very close results produce totally different results. The only difference I see is the old compiled as win32 threads vs. pthreads but parallelism (-P 10) appears to work in both. Anyone has a clue or can recommend a tool that gives results I can trust?? EDIT: Looking at traces from (old) iperf it sets the TCP Window Scale flag to 3 in the SYN packet, when I run the (new) iperf this is set to 0 in the initial packet. A quick analysis of the window size through the exchange shows the (old) iperf moving back and forth but mostly at 32k while the (new) iperf mostly keeps at 64k. Maybe it will help somebody to connect the dots.

  Read the article

< Previous Page | 677 678 679 680 681 682 683 684 685 686 687 688  | Next Page >