Search Results

Search found 3356 results on 135 pages for 'removing'.

Page 8/135 | < Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >

• After connecting wlan0 to bridge interface (and then removing it), can't connect to AP

  - by gmonk

  I'm on a laptop running Debian Jessie with kernel 3.13-1-amd64; lspci shows that my wireless NIC + driver is 04:00.0 Network controller: Intel Corporation Wireless 3160 (rev 83) Subsystem: Intel Corporation Dual Band Wireless-AC 3160 Kernel driver in use: iwlwifi This has been working without any problems, until I tried creating a bridge for lxc containers to use. I did the same thing as this person here: How-to set up a network bridge on a laptop for LXC use? -- and ended up having the same problem as this poster did, so I decided to "undo" my actions. This hasn't been successful. Actions taken so far: To configure the bridge: #> ip link add type veth #> iw dev wlan0 set 4addr on #> ifconfig veth0 up #> brctl addbr br0 #> brctl addif br0 wlan0 #> brctl addif br0 veth0 #> ifconfig br0 192.168.0.4/24 #> ifconfig wlan0 0.0.0.0 To "deconfigure": #> brctl delif br0 wlan0 #> brctl delif br0 veth0 #> iw dev wlan0 set 4addr off #> ifconfig veth0 down #> ifconfig wlan0 down #> ifconfig br0 down #> brctl delbr br0 Now, dmesg and /var/log/syslog show repeated attempts at connecting to the AP that was working before, which fail after authentication: May 27 09:16:01 myhostname kernel: [11350.757172] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:01 myhostname kernel: [11350.759036] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:01 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:01 myhostname kernel: [11350.762615] wlan0: authenticated May 27 09:16:01 myhostname kernel: [11350.762753] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:01 myhostname kernel: [11350.762755] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:01 myhostname kernel: [11350.765080] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:01 myhostname kernel: [11350.767474] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=12 aid=0) May 27 09:16:01 myhostname kernel: [11350.767476] wlan0: 00:18:f8:54:a3:d6 denied association (code=12) May 27 09:16:01 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:18:f8:54:a3:d6 status_code=12 May 27 09:16:01 myhostname kernel: [11350.788475] wlan0: deauthenticating from 00:18:f8:54:a3:d6 by local choice (reason=3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> disconnected May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:02 myhostname dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 14 May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:04 myhostname kernel: [11354.559579] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:04 myhostname kernel: [11354.561458] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:04 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> associating May 27 09:16:04 myhostname kernel: [11354.563445] wlan0: authenticated May 27 09:16:04 myhostname kernel: [11354.563631] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:04 myhostname kernel: [11354.563633] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:04 myhostname kernel: [11354.565727] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: Associated with 00:18:f8:54:a3:d6 May 27 09:16:04 myhostname kernel: [11354.568091] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=0 aid=9) May 27 09:16:04 myhostname kernel: [11354.569030] wlan0: associated May 27 09:16:04 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> associated May 27 09:16:05 myhostname kernel: [11354.978204] wlan0: deauthenticated from 00:18:f8:54:a3:d6 (Reason: 15) May 27 09:16:05 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:18:f8:54:a3:d6 reason=15 May 27 09:16:05 myhostname kernel: [11354.992729] cfg80211: Calling CRDA to update world regulatory domain May 27 09:16:05 myhostname kernel: [11354.995004] cfg80211: World regulatory domain updated: May 27 09:16:05 myhostname kernel: [11354.995005] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) May 27 09:16:05 myhostname kernel: [11354.995006] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995007] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995007] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995008] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995009] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995010] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) May 27 09:16:05 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associated -> disconnected May 27 09:16:05 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:09 myhostname kernel: [11358.763968] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:09 myhostname kernel: [11358.765796] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:09 myhostname kernel: [11358.769957] wlan0: authenticated May 27 09:16:09 myhostname kernel: [11358.770102] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:09 myhostname kernel: [11358.770104] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:09 myhostname kernel: [11358.770846] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:09 myhostname kernel: [11358.773358] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=12 aid=0) May 27 09:16:09 myhostname kernel: [11358.773361] wlan0: 00:18:f8:54:a3:d6 denied association (code=12) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:18:f8:54:a3:d6 status_code=12 May 27 09:16:09 myhostname kernel: [11358.802187] wlan0: deauthenticating from 00:18:f8:54:a3:d6 by local choice (reason=3) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> disconnected May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:12 myhostname kernel: [11362.573442] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:12 myhostname kernel: [11362.575270] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:12 myhostname kernel: [11362.580334] wlan0: authenticated May 27 09:16:12 myhostname kernel: [11362.580503] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:12 myhostname kernel: [11362.580516] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:12 myhostname kernel: [11362.583508] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: Associated with 00:18:f8:54:a3:d6 May 27 09:16:12 myhostname kernel: [11362.585908] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=0 aid=9) May 27 09:16:12 myhostname kernel: [11362.586781] wlan0: associated May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> associated May 27 09:16:13 myhostname kernel: [11362.947693] wlan0: deauthenticated from 00:18:f8:54:a3:d6 (Reason: 15) May 27 09:16:13 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:18:f8:54:a3:d6 reason=15 May 27 09:16:13 myhostname kernel: [11362.973461] cfg80211: Calling CRDA to update world regulatory domain May 27 09:16:13 myhostname kernel: [11362.975673] cfg80211: World regulatory domain updated: May 27 09:16:13 myhostname kernel: [11362.975675] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) May 27 09:16:13 myhostname kernel: [11362.975676] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975677] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975678] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975678] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975679] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975679] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) May 27 09:16:13 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associated -> disconnected May 27 09:16:13 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:14 myhostname NetworkManager[13992]: <warn> Activation (wlan0/wireless): association took too long. May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): device state change: config -> failed (reason 'no-secrets') [50 120 7] May 27 09:16:14 myhostname NetworkManager[13992]: <info> Marking connection 'Auto myaccesspoint' invalid. May 27 09:16:14 myhostname NetworkManager[13992]: <warn> Activation (wlan0) failed for connection 'Auto myaccesspoint' May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): device state change: failed -> disconnected (reason 'none') [120 30 0] May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): deactivating device (reason 'none') [0] May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> disconnected The things that jump out at me are "deauthenticating ... by local choice( reason=3)" and the lines that contain "(reason=15)". I've tried various fixes: iwconfig wlan0 power off killing wpa_supplicant connecting with iwconfig + dhclient instead of gnome's network -manager explicitly configuring wlan0 in /etc/network/interfaces creating a /etc/wpa_supplicant.conf file ...but nothing seems to work. I'm not sure what I did wrong, or what step I've skipped in trying to get wlan0 back as a non-bridged device -- I removed it from the bridge and then deleted the bridge itself. Any ideas?

  Read the article

• Removing a malware that sets up as a system driver

  - by ereOn

  Hello, I recently tried to fix up my mother's computer which has some serious malwares. One of them apparently registered itself as system driver (tjbijkoq.sys if that can help) and after running a malware suppression tool, the computer won't boot anymore, complaining about a "critical driver that is missing". I think deleting the matching entry in the registry would just solve the problem, but obviously I can't boot up the computer (even in safe mode) to fix it. Do you guys have any experience with such an issue and how to solve this ? Thank you very much. The operating system is Windows Vista 32 bits Professional

  Read the article

• Removing phantom applications from Application Pools in IIS7

  - by Col

  I have an application in one of my application pools that has a virtual path of '/Site/login.aspx'. I want to remove it but it no longer exists on my computer and it's causing me issues setting up AppFabric. I understand that you can remove these phantom applications by recreating the application in IIS and then hitting Remove. That will get rid of the application from the pool but in this case I can't recreate the application due to the /login.aspx in the virtual path Any ideas how I remove this erroneous entry? Thanks

  Read the article

• Removing write permission on home and public_html on Centos/Cpanel

  - by user5858

  I'm running sites on two Cpanel accounts on my VPS on WHM. I'm using DSO php handler and Apache server on my Web server. After recent intrusion attacks I've chowned to root with permission 555 on $HOME and public_html folder. I'm on VPS with Cpanel on Centos. I'm running CMS based software like Joomla Drupal etc. Will this cause any problem to my VPS installation or server side processes? Drupal, Joomla, MyBB etc will not be affected by this. Some files will not be created like error_log. At least hackers will not be able to place any malicious code within home folder or the public_html folder.

  Read the article

• Removing extended partition without deleting logical in it

  - by HisDudeness

  I'm running a Linux-based laptop, and in order to multi-boot several distros in it, I created an extended partition which contains a bunch of logical ones with GParted. Now, after quite a long time with this setup, I've changed my mind because of the consequent lack of storing space for my data partition. Now I want to keep one distro alone like it's normal, and eventually have some other operating systems stored in external supports to plug in and use if I want. Obviously, also this partition I want to keep (and to enlarge a little too) is just a logical inside the extended I want to keep. For what concerns the number I'm ok, meaning I currently have this big distro dedicated extended, the swap and the data partitions, so there's space for another primary before I delete the extended, but I don't know how to delete it without touching the logical in it, I don't want to reinstall the system losing all changes and settings, and I don't want to keep an extended partition for a logical alone. How can I do? Do I have to create a new primary, copy the logical content in it and then delete everything? Will the system boot and maintain exactly all the features it has now? Or is there a way to convert an extended into a primary once it contains just one logical? Or can I directly move a logical out of an extended turning it into a primary? Or, again, am I screwed?

  Read the article

• Removing partition to install OS?

  - by Shane

  So i have a computer that has 2 hard drives and i installed Ubuntu server on it. I used LVM to connect the two. So i tried to put windows back on it but it failed because it said it couldn't position the drive and then when i booted again the OS couldn't be found. So i booted it with the Ubuntu setup disc but now when it goes to partition it says that the position can not be modified because its already in use. I am asking if there is a way i can just remove everything and start fresh?

  Read the article

• Nitro PDF Express removing already outputted files when I cancel it

  - by Nrew

  Im converting lots of .doc files into .pdf using Nitro PDF Express. The program isn't finish converting the 37 files yet maybe 10 are converted and are in the output directory already. But when I cancelled it, even the converted one's are deleted. Can I still find it somewhere or are they gone for good.

  Read the article

• cpu fan keeps getting faster after removing battery

  - by super_sonic

  Hi all, I have recently pulled the battery out of the motherboard on an old Acer desktop to reset the bios, but when I put the battery back in after about 3-4 hours, and start it up, the cpu fan just keeps getting faster and faster, like it won't stop at all. Does anyone know of a way to fix this problem? Cheers!

  Read the article

• Removing files with strange names

  - by pythonic metaphor

  Somehow I ended up with a file named "-r". How do I remove it? rm -r doesn't work. I tried 'rm -i `ls -a`' to step through the file names, but it didn't prompt me to delete this one. Edit A very hacky approach was to use python's os.unlink function. That worked, but I'm curious to hear other ways.

  Read the article

• Removing Paths/ Landing Pages From SharePoint Search Results

  - by j.strugnell

  Hi there, We've been asked by a client to remove a number of pages from being shown up in their public website search results page. I've been into the SSP and created Crawl Rules to remove these pages. All seemed to have worked ok but we have an issue in that landing pages are still showing up in their "www.domain.com/sitearea/" form but not in their "www.domain.com/sitearea/pages/default.aspx". For each of this type of page we have created one rule to "Exclude" the "aspx" path and another rule to include the "/" path but to "Follow links on the URL without crawling the URL itself". We tried adding rules to exclude the "/" format but that only resulted in all results underneath that being excluded. Does anybody know how to remove the "area/pages/default.aspx" and the "area/" pats from Search Results? I'm not sure if it's the "done thing" to ask 2 questions in one but this is in a similar vein so it should be ok. I was wondering if anyone knew of a tool (or if it is possible) to allow site admins to exclude pages from search results (not via SSP/Crawl Rules). I know they can do it at the site level but I was wondering if anything out there enabled this to be done at the page level through either Page or Site Settings?

  Read the article

• Laptop screen turns off on removing power cord

  - by YatharthROCK

  After a recent upgrade to Windows 8.1 Pro from W8, my laptop's screen turns off as soon as you remove the power cord. It turns back on with no issues when you plug the power back in. Keyboard and mouse input is processed while the screen is off. My settings tell the screen to go off after 2 minutes of inactivity on battery. I was having a battery issue from before where my laptop would should down after 5 minutes of running on battery (despite showing 60% left), but I think that's unrelated. Any other info will be provided on request. Can anyone help me figure out what's going on? How can I stop this behaviour?

  Read the article

• Removing orphan vmware images

  - by Brad Bruce

  I am trying to remove some VMWare images that were created by a machine that is no longer available. We do not plan to use VMWare and would like to clear up the space. I get a message Cannot delete [filename]... for all of the files in these directories. Can anyone tell me how to delete them (short of reformatting)? Thanks

  Read the article

• Preventing Windows from automatically removing broken desktop shortcuts

  - by hkBattousai

  I have two external harddrives which I'm using for archiving purposes, because of that they are turned off most of the time. I have some shortcuts on the desktop to some directories on these external harddisks. Windows occasionally removes these desktop shortcuts. It happens when the harddisks are turned off. I think it thinks that the shortcuts are broken and no longer needed, and tries to clean the desktop up. How do I prevent this behavior? (OS Version: Windows 7 Ultimate x64 SP1)

  Read the article

• Removing information about deleted volume

  - by Pravin

  In order to increase space in my c drive, I had to delete all my volumes and create again allocating more space to C which I did, after which my drive name G didn't exist. Before this I used to install all my softwares in G. Now since the drive does not exist, I want to remove all info about the softwares I installed in G as they got deleted when volume got deleted. I also want to install cilk++ but it gives me an error-invalid drive g:. If I insert pendrives so I get a volume named G, cilk++ installer runs but says that it will be integrated to visual studio 2008 which i previously had in G drive(but no longer exists) and doesn't show visual studio 2010 which i recently installed in C drive. How do I fix this? Please help.

  Read the article

• Removing a Program from Win7's Start Menu forever ?

  - by Mohammad

  I'm gonna remove YM! icon from Win7's Start Menu for good, I mean I wanna remove it even I use it. I've been using Right Click >> Remove From This List but It comes back after using once!!! http://www.picfront.org/d/7vf3 How can I remove the program from above list forever?

  Read the article

• removing a trailing slash from a filename (index.php/to index.php)

  - by Steve

  Hi, I'm sure I'm missing a trick here but I can't work out how to remove the trailing slash from a file name in a URL. My URL would be something like this: www.mysite.com/dynamic_folder_name/index.php/ I need the URL to become www.mysite.com/dynamic_folder_name/index.php Any help would be appreciated. Cheers

  Read the article

• removing specific warnings in Apache error.log

  - by Tereno

  Here's my situation. I have a directive that goes something like this: Options MultiViews FollowSymLinks I have a location directive where I have Options +Includes This causes warning errors in my Apache error log: mod_include: Options +Includes (or IncludesNoExec) wasn't set, INCLUDES filter removed These warnings are gone when I add +Includes to my options but I don't want. I want to have the Includes filter removed but without having warning errors. If there's something unclear, feel free to ask. Thanks

  Read the article

• "save the changes" message after removing the protection from workbook Excel 2010

  - by abbasi

  Some time ago I protected the Excel 2010 file from the path File Protect workbook Encrypt with password and gave it a password. Now that I removed that password via below method: Open the workbook and use Save As In the lower right of the file window will be "Tools" Choose "General Options" Clear the password. Save over your old file. the file is openable without wanting a password. But the problem is when I open it and close it immediately, even without moving the active cell, the message "Do you want to save the changes you made to 'test.lsx'?" appears. While there hasn't occurred any changes to that file so why I face this message any time I want to close the file? Hasn't the file been corrupted?

  Read the article

• Removing raid 1 (mirroring) and leaving data on both drives

  - by ajma

  Hello, I have two drives in a raid 1 (mirroring) array. Hardware raid using whatever is built into an Intel motherboard. (asus P5BE) I'd like to remove one drive but keep the data in both (I want to put one of the drives into another machine). Can I go into the raid configuration and remove the array and have the data remain?

  Read the article

• Removing integrated video card drivers broke other hardware?

  - by jsnlxndrlv

  I just purchased and installed an XFX ATI Radeon HD 4650 video card. The installation instructions said to remove the old video card drivers before installing the new driver. I did both things, but now every time I start my computer, the Found New Hardware wizard pops up for the following three devices: PCI Device SM Bus Controller Other PCI Bridge Device Furthermore, my LAN port no longer functions. The cable's connected, and the light on the port comes on, but the computer can't find any servers when I attempt to connect with it. The modem and router are working, and obviously I'm able to use the other computer here to post this. What do I do to fix this?

  Read the article

• Virtual Host Configuration and mod_rewrite - Removing PHP Extension and Adding Forward Slash

  - by nicorellius

  On my production server, things are fine: PHP extension removal and trailing slash rules are in place in my .htaccess file. But locally, this isn't working (well, partially, anyway). I'm running Apache2 with a virtual host for the site in question. I decided to not use the .htaccess file in this case and just add the rules to the httpd-vhosts.conf file instead, which, I've heard, if possible on your server, is a better way to go. The virtual host is working and the URL I use for my site is like this: devserver:9090 Here is my httpd-vhosts.conf file: NameVirtualHost *:9090 # for stuff other than this site <VirtualHost *:9090> ServerAdmin admin@localhost DocumentRoot "/opt/lampstack/apache2/htdocs" ServerName localhost </VirtualHost> # for site in question <VirtualHost *:9090> ServerAdmin admin@localhost DocumentRoot "/opt/lampstack/apache2/htdocs/devserver" ServerName devserver <Directory "/opt/lampstack/apache2/htdocs/devserver"> Options Indexes FollowSymLinks Includes AllowOverride None Order allow,deny Allow from all </Directory> <IfModule rewrite_module> RewriteEngine ON # remove PHP extension and add trailing slash # note - this doesn't work for directories, and throws 404 # TODO - fix so directories use index.php RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{THE_REQUEST} ^GET\ /[^?\s]+\.php RewriteRule (.*)\.php$ /$1/ [R=302,L] RewriteCond %{REQUEST_FILENAME} !-d RewriteRule (.*)/$ /$1.php [L] RewriteCond %{REQUEST_FILENAME}.php -f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule .*[^/]$ /$0/ [R=302,L] </IfModule> # error docs ErrorDocument 404 /errors/404.php </VirtualHost> The problem I'm facing is that when I go to directories on the site, I get a 404 error. So for example, this: devserver:9090/page.php goes to devserver:9090/page/ but going to a directory (that has an index.php): devserver:9090/dir/ throws 404 error page. If I type in devserver:9090/dir/index.php I get devserver:9090/dir/index/ and the contents I want appear... Can anyone help me with my rewrite rules?

  Read the article

• Removing expired self-signed certificate in IE9 (created with IIS7.5)

  - by Itison

  Over 1 year ago, I created a self-signed certificate in IIS 7.5 and exported it. I then installed it for IE9 (it may have been IE8 at the time), which worked fine until a year later when the certificate expired. I have put this off, but today I created a new self-signed certificate in IIS, exported it, and attempted to install it in IE9. The problem is that for whatever reason, IE cannot seem to forget about the old, expired certificate. Here's what I tried initially: Accessed my ASP.NET application and see the Certificate error. Clicked "View certificates". Clicked "Install Certificate" and then Next/Next/Finish. At this point, it says the import is successful, but it still only shows the expired certificate. I've tried simply double-clicking on the exported certificate on my desktop. Initially I chose to automatically select the certificate store, but then I tried it again and manually selected "Trusted Root Certification Authorities". I've also tried dragging/dropping the certificate over an IE window and clicking "Open". The process is then exactly the same as it is if I had double-clicked on the certificate, but I had hoped that this would somehow specifically tell IE to use this certificate. I tried opening MMC and with the Certificate snap-in, confirmed that the new certificate was added under "Trusted Root Certification Authorities". It was also under my "Personal" certificates (I guess this is where it goes by default). Nothing worked, so I went through every folder in MMC and deleted the expired certificate. I also deleted the expired certificate in IIS. Nothing has worked. Any ideas? I see no clear resolution and I can't seem to find any posts related to this issue.

  Read the article

• Removing file with strange characters in filename in OS X

  - by SiggyF

  After a memory error in my program, I am stuck with a file with a strange filename. It's proving quite resistant to all normal methods to remove files with strange names. The filename is: %8BUȅ҉%95d%F8%FF%FF\x0f%8E%8F%FD%FF%FF%8B%B5T%F8%FF%FF%8B%85\%F8%FF%FF\x03%85x%F8%FF%FF%8B%95D%F8%FF%FF%8B%BD%9C%F8%FF%FF%8D\x04%86%8B%B5@%F8%FF%FF%89%85%90%F8%FF%FF%8B%85X%F8%FF%FF\x03%85%9C%F8%FF%FF%C1%E7\x02%8B%8Dx I tried the following: rm * - "No such file or directory" rm -- filename - "No such file or directory" rm "filename" - "No such file or directory" ls -i to get the inode number - "No such file or directory" stat filename - "No such file or directory" zip the directory where the file is in - error occured while adding "" to the archive. delete directory in finder - error -43 in python: os.unlink(os.listdir(u'.')[0]) - OSError No such file or directory find . -type f -exec rm {} \; - "No such file or directory" checked for locks on the file with lsof - no locks All these attempts result in a file (long filename here) not found error, or error -43. Even the ls -i. I couldn't find anymore options, so before reformatting or repairing my filesystem (fsck might help) I thought maybe there is something I missed. I wrote this small c program to get the inode: #include <stdio.h> #include <stddef.h> #include <sys/types.h> int main(void) { DIR *dp; struct dirent *ep; dp = opendir ("./"); if (dp != NULL) { while (ep = readdir (dp)) { printf("d_ino=%ld, ", (unsigned long) ep->d_ino); printf("d_name=%s.\n", ep->d_name); } (void) closedir (dp); } else perror ("Couldn't open the directory"); return 0; } That works. I now have the inode, but the normal find -inum inode -exec rm '{}' \; doesn't work. I think I have to use the clri now.

  Read the article

• some issues with removing www and redirecting index.html

  - by MariaKeys

  Hello Fellas, I am having trouble doing what i want to do with the following setup. I would like to remove all WWW, and also forward index.html to root dir. I would like this to be for all domains, so i am doing inside httpd.conf directory directive. I tried many variations with no success. Latest version is below (domains are inside /var/www/html, in seperate directories). http://www.example.com/index.html > http://example.com http://www.example.com/someother/index.html > http://example.com/someother/ Thanks, Maria <Directory "/var/www/html/*/"> RewriteEngine on RewriteBase / RewriteCond %{HTTP_HOST} ^www\.(.+)$ [NC] RewriteRule ^(.*)$ http://%1/$1 [R=301,L] #RewriteCond %{REQUEST_URI} /^index\.html/ RewriteRule ^(.*)index\.html$ / [R=301,L] Options ExecCGI Includes FollowSymLinks AllowOverride AuthConfig AllowOverride All Order allow,deny Allow from all </Directory>

  Read the article

• How to prevent MediaWiki removing non default signatures?

  - by WikiSpeedia At Area51

  We recently upgraded MediaWiki from 1.13.2 to 1.15.4. One of the side effects is that people's signatures are automatically deleted. That is, a signature added under MY PREFERENCES gets changed to match the Real Name field after a couple of minutes. We set $wgCleanSignatures = false in LocalSettings.php but this does not change the behaviour. Does anyone know what is going on and how to prevent this?

  Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >