Search Results

Search found 2911 results on 117 pages for 'payment gateway'.

Page 80/117 | < Previous Page | 76 77 78 79 80 81 82 83 84 85 86 87  | Next Page >

• can not access dlink 604 set up interface

  - by user36089

  Hello everyone I used dlink-di604 enthernet board as router to share web access. My ISP provides the service base on Ethernet rathern than base on Ethernet pppoe mode. It is manually setup ipv4, subnet mask , DNS, Gateway etc Log in using web user name&password. I use http://192.168.0.2 try to access dlink di604 setup inferface, but failed I call command ipconfig /all Dos shell displayed: Ethernet adapter Local Connection: Physical Address: 00-3c-56-79-19-49 IPv4 address:10.7.8.225 subnet mask: 255.255.255.0 default gate way: 10.7.8.1 DNS servers 10.10.10.10 What is the correct way to access dlink 604 setup interface and set to share web access? Welcome any comment Thanks interdev

  Read the article

• Using a Dell PowerConnect to set up load balancing/redundancy, 1 switch 2 routres 2 private wan link

  - by MarianoC

  Hi, We have different locations connected by two different WAN providers. Each site has a dell powerConnect 6224 and two cisco routers with the WAN connections (we don’t have access to router admin). The 6224 connects to each cisco LAN port and to our LAN backbone. We would like the 6224 provide the ip gateway address and load balance and support redundancy, if one of the routes fail. Is this possible?. We can't find any samples on doing this and we have tried with no success. Any help or link to documentation regarding this, will be greatly appreciated. Thanks, MarianoC

  Read the article

• Windows 2003 - RAS service - VPN client can only connect to server, not internal network

  - by Gk

  Here is my diagram http://imageshack.us/photo/my-images/263/vpnt.png/ Server has two NIC: One connect to Internet, one connect to internal network. RAS service is configured with static IP pool on the same subnet of internal network (10.10.0.x). The problem is when a client connect to server, client can connect to server(10.10.0.10), but cannot connect to another host locate in internal network (10.10.0.11) even cannot ping to 10.10.0.50. RAS configured with IP routing enabled, client connect with options: Use default gateway on remote network. I'm messed up and can not figure out what wrong. Please help me T_T. TIA, giobuon

  Read the article

• VM clients can not access WAN

  - by Saariko

  I have a new VM host on my network, on a Dell R620. The dedicated iDrac is connected with static IP of: 192.168.3.x NIC #1 is connected to my router The eSXI 5.1 host is with IP of 192.168.3.250 The vSphere appliance has a static IP of 192.168.3.241 All the clients on the new host are in the same network 192.168.3.x All clients are Windows 2008 R2 My problem is that non of the clients can access the WAN. I can't ping anything which is beyond my router. I CAN ping anything within my router, even if it's on a different subnet - 192.168.0.x (Router rules are in tact and working) I can ping the gateway (192.168.3.254) One thing that I checked, and is bothering my (but don't know if it has any relevance) is that on the Host Networking properties, there is a vmnic0 (picture) that shows as if it only recognizes 192.168.0.x network - is that so? The command: route print shows me the following details, where I have a duplicate entry for 0.0.0.0 (and one is wrong) - which is probably also why it's not working

  Read the article

• Windows VPN - NO internet access

  - by sharru

  I host a network of servers behind a Fortigate 200a firewall in the DC. I connect to those servers via a VPN connection. The problem is that when i connect to the VPN, I lose my internet connection on the local PC (windows 7). I would like to be connected to the VPN and still surf the web. i guess this means to only forward a range of ip to the VPN connection. I've read other answers on serverfault, talking about "un-check the 'Use default gateway on remote network' option in your Windows 7 PPTP network connection settings". When i do that , i get internet access but no access to the servers in the VPN. Any idea how to get both working? Should i change something on the fortigate 200a config? Do i need two networks cards? Is there a place in windows to define ip range for the vpn connection?

  Read the article

• Unable to access internet if wireless enabled

  - by balki

  The following is my route output. eth0 is my wired network and eth1 is my wireless network. Only wired one has access to internet. If I enable wireless, I am not able to access internet, it tries to access via eth1 and I get 404 page of the wireless router. Why does eth1 have higher preference though default is eth0 (link)? [balakrishnan@mylap ~]$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.26.0.1 0.0.0.0 UG 0 0 0 eth0 10.26.0.0 * 255.255.192.0 U 1 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 192.168.1.0 * 255.255.255.0 U 9 0 0 eth1

  Read the article

• New power supply and now HDDs are not recognized

  - by Michael

  So I upgraded to a new X4 ULTRA power supply that was recommended to me by a local TigerDirect store. After installing it along with a new liquid cooling system, I booted it up and it automatically fried my CD Drive. After that I noticed that the OS wouldn't start and figured out that none of the 4 HDDs in my computer were being recognized by the BIOS. I feel them spool at a steady pace and have tried new cables and connections but to no avail. I triple checked all of the connections and cables and have no idea what is wrong. This isn't the first time I changed a PS or CPU cooling system but I am at a dead end. Any ideas, aside from buying a USB HDD reader and seeing if they are all fried? Also, this is a stock Gateway mobo with the mobo USB connections already dead. Could the new PS have fried the SATA connections??

  Read the article

• Remove a known network from Windows 8

  - by Edward Brey

  When Windows 8 detects a network based on the assigned IP address, netmask, default gateway, etc., it remembers the network along with the setting you give it as a public or private network. If you change the configuration of a network (e.g. reconfigure your router), Windows may determine you are on a new network and assign it a name of Network 2 or YourAPN 2. This less-than-friendly name shows up in many places in the Windows 8 UI, but unlike the good old days of Windows 7, there doesn't appear to be any UI to merge or delete these networks. What's the best way to merge or delete networks you don't want?

  Read the article

• How to elegantly selectively exclude FreeBSD network traffic from OpenVPN interface by port

  - by Polygonica

  inexperienced sysadmin here. I'm planning on running a net daemon inside a FreeBSD jail through OpenVPN, but want to be able to SSH directly into the jail and use the daemon's web interface daemon without going through the VPN. As I understand it, an OpenVPN tunnel is normally set up as a default virtual internet interface, and so incoming traffic will go out on the OpenVPN interface by default (which is problematic, as this incurs latency). I thought "well, obviously, since all of this traffic is leaving on a handful of ports, I'll just redirect those to the non-VPN gateway." I've tried to look for solutions, but almost all of them involve iptables instead of ipfw (which is default for FreeBSD) and solve slightly different problems. And alternate solutions like using multiple default routes to ensure that incoming traffic on any interface is always sent out on the same interface seem far-reaching and require deep knowledge of all tools involved. Is there an elegant way of ensuring that traffic leaving on specific ports exits on a specified non-default interface using ipfw?

  Read the article

• A can ping B, B can ping C but A cant ping C. How do i connect A to C (ethernet)?

  - by user16654

  I have a computer at home with ip 192.168.221.xxx I have another computer at work that I can ping and it has 2 ip addresses: 192.168.1.xxx and 192.168.0.xxx. Those last 2 addresses have the same gateway ie 192.168.1.1 . The computer at work is connected to a hub. That hub also has an embedded device connected to it with address 192.168.0.xxx Now from my home computer I cannot ping this embedded device. How would I connect to it without changing the subnetwork it connects to? I can ping the embedded device from my work computer and I can ping the work computer from my home computer. So I am trying to connect to the embedded device from my home computer through my work computer. Port forwarding? how would I establish that on Ubuntu?

  Read the article

• Attempted hack on VPS, how to protect in future, what were they trying to do?

  - by Moin Zaman

  UPDATE: They're still here. Help me stop or trap them! Hi SF'ers, I've just had someone hack one of my clients sites. They managed to get to change a file so that the checkout page on the site writes payment information to a text file. Fortunately or unfortunately they stuffed up, the had a typo in the code, which broke the site so I came to know about it straight away. I have some inkling as to how they managed to do this: My website CMS has a File upload area where you can upload images and files to be used within the website. The uploads are limited to 2 folders. I found two suspicious files in these folders and on examining the contents it looks like these files allow the hacker to view the server's filesystem and upload their own files, modify files and even change registry keys?! I've deleted some files, and changed passwords and am in the process of trying to secure the CMS and limit file uploads by extensions. Anything else you guys can suggest I do to try and find out more details about how they got in and what else I can do to prevent this in future?

  Read the article

• XenServer 5.6.1-fp1. Can't get network working

  - by casey_miller

  I have a PC where XenServer 5.6.1 fp-1 has been successfully installed. I've manually set the network settings: 192.168.1.50 255.255.255.0 192.168.1.1 but it's set to xenbr0 iface. While eth0 is empty. When I click on "Configure Management Inteface" it shows that eth0 is connected. But when I ping a default gateway (which is 100% should be accessible) it fails. I used to another shell (Alt+F3) and logged as root. I also failed to ping. with both: ping -I eth0 192.168.1.1 and ping -I xenbr0 192.168.1.1 Be assured that: Cable works Ethernet adapter is 100% functional (prev OS was Ubuntu it was working) There is no firewall rule to deny anything. (everything is allowed) So the question is: What is a problem???

  Read the article

• How to route traffic from VM (Parallels) over an Open VPN connection on the host (OS X)

  - by withakay

  Scenario: I have a Mac running Lion that is connected to an OpenVPN server I have a Windows XP VM (running on parallels, but I don't think this is important) I want to be able to route traffic from the XP VM via the host Mac's OpenVPN connection so that I can log on to a domain. The remote network is 172.16.0.0/23 (255.255.254.0) Open VPN is configured to supply address in the 10.100.101.0/24 range and sets up the routing to 172.16.0.0 using the gateway 10.100.101.1/32 My local network is 192.16.1.0/24 NOTE: I do not want to install OpenVPN into the XP virtual machine as I would have to use a passwordless key in order for OpenVPN to connect before logon. Anyone got any ideas?

  Read the article

• How do I change the Admin password on a Ubee DVW3201B?

  - by Iszi

  I must admit that I feel rather foolish having to ask this. I recently switched ISPs, and the new one gave us a Ubee DVW3201B as our home gateway. I want to change the Administrator username/password from the defaults, but I've been having some difficulty. Every time, after I save the new username and password, I'm prompted to re-authenticate to the administration interface. It fails no matter what I try. I've tried using: New username / New password Default username / New password Default username / Default password None of the above works. This has happened twice now, with my only recourse after failure being to do a reset to factory defaults (press and hold the hard reset button for 10 seconds). Is there something I'm missing?

  Read the article

• ubuntu server in a vm, can't connect to internet

  - by jessh

  I'm attemtping to host my own development web server in a virtual box guest, Ubuntu Server. I would like this virtual machine to be accessible from not only my home network, but outside the LAN as well. As such, I've set up a static IP (so I can later forward ports to this static IP.) My virtual box settings have this vm only using one adapter -- in bridged mode. Here's what my /etc/network/interfaces looks like: iface eth0 inet static address 10.0.1.203 /*this is outside the DHCP range*/ netmask 255.255.255.0 gateway 10.0.1.1 network 10.0.1.0 broadcast 10.0.1.255 dns-nameservers: 8.8.8.8 8.8.8.4 Here's what the output of ifconfig looks like: https://dl.dropbox.com/u/2241201/locker/ubuntu.png My Host is a mac mini, running OS X 10.7. From within the guest, if I ping google.com: $ ping google.com # outputs 'ping: unknown host google.com' immediately Why am I unable to access the web?

  Read the article

• NSD reply from unexpected source

  - by Ximik

  I have server with NSD. There are MAIN_IP and ADD_IP. When I try to get IP of my site from server I have right output dig @localhost my_site.com But when I try to make this from my PC, I have dig @my_ns_server.com my_site.com ;; reply from unexpected source: MAIN_IP#53, expected ADD_IP#53 (ADD_IP is IP of my_ns_server.com) What should I do? UPD: My interfaces conf auto eth2 allow-hotplug eth2 iface eth2 inet static address xxx.xxx.xxx.234 netmask 255.255.255.252 network xxx.xxx.xxx.232 broadcast xxx.xxx.xxx.235 gateway xxx.xxx.xxx.233 dns-nameservers MY_ISP_IP dns-search MY_ISP_DOMAIN auto eth2:0 iface eth2:0 inet static address xxx.xxx.xxx.124 netmask 255.255.255.0 xxx.xxx.xxx is the same for all IPs

  Read the article

• Failover NIC with Windows 7 running Apache Server

  - by Benjamin Jones

  I have a Apache Server running on a Windows 7 Desktop for a internal website (Intranet). I am trying to figure out how I can make this system as failover safe as possible. One thing I want to do is use the 2nd NIC card that is currently disable. I only have one gateway address to my router. I do not have any computer running a Server O/S. If NIC1 crashes by chance(just humor me!), how could NIC2's IP take on the host name (I have mapped in host file) . I don't really care if the static IP of NIC2 changes seeing that the host name is the only thing I need. Could I add two IP's to the host file, with same host email and maybe create some script that will run IF NIC 1 fails? OR is there any failover software that will do this for me?

  Read the article

• Setting up WiFi extenders... is it possible to daisy-chain them?

  - by Bigbio2002

  At a location with limited cabling, I've had to set up WiFi signal extenders to cover the whole area. Here is a crude diagram... Internet - WiFi/Gateway - Extender 1 - Extender 2 | | PC (ethernet) WiFi device I was able to successfully daisy-chain three together, and I can access the internet from WiFi devices connected to the farthest extender. Is this a supported configuration? If not, what kind of issues can arise from it? The reason why I ask is that the PC keeps reporting IP address conflicts, and I'm wondering if that's caused because of the way this is configured. Additionally, I noticed that the extenders named their own SSID similar to the one they are connected to, but with a suffix. Would there be any issue in naming them all with the same SSID, to enable seamless roaming as you would with multiple standalone APs?

  Read the article

• Accessing VMware Player across the network

  - by Tiffany Walker

  My network: 192.168.2.2 (computer) 255.255.255.0 (mask) 192.168.2.254 (gateway) The VMplayer is: 192.168.233.129 (ip) 255.255.255.0 (mask) 192.168.233.255(bcast) It's obvious the player can't be access from other systems because of the wrong network settings. However, I am not sure as to how to change that. Obviously I have to edit the ifcg-eth0 but I know I also need to edit it on the host system to make it accessably. Is this done from inside VMware Player? Or do I need to edit the network devices? The host box is Windows. Inside VMware is Linux.

  Read the article

• Internet connection sharing windows server 2008 R2

  - by This is it

  I have one windows server 2008 r2, and that server has 4 network interfaces (3 private, 1 internet connection). I would like to share internet connection with other 3 networks. Windows server firewall should make logs of data that is transfered. It should not be possible to connect directly to private networks from internet. How could I do it? Edit: I tried with NAT in RRAS, but it doesn't work. Here is the configuration: Server: IP private:192.168.0.1 IP public: xx.xx.xx.xx client IP:192.168.0.2 Default gateway: 192.168.0.1 Public and private interface added in NAT section of RRAS.

  Read the article

• Connecting guest OS to host os internet connection hyper-v

  - by autrevo

  Hyper-V internal switch and VM OS interfacing with Guest OS and IP Cofiguration When configuring hyper-v internal switch, Apart from physical lan adapter (say adapter 1), I see another LAN adapter (say adapter 2) added in host os. And we already have one virtual lan adapter in guest os, (say adapter 3) . adapter 1 is connected to internet with defaulty gateway say, 192.168.0.254 and uses class C IP. By con configuring adapter 2 and 3, I need to acheive two purpose - Access internet in guest os. seemlessly share files & folders between guest and host OS. Please, suggest, What is the best way to configure IP of these three adapters ?

  Read the article

• Simple secured SFTP tunnel?

  - by babonk

  I'd like to setup an sftp tunnel so that I can connect to an IP-secured SFTP server through a gateway computer from anywhere, and download the files to anywhere. I was thinking of using a combination with netcat, having it listen to either WinSCP or PuTTY sFTP (doesn't matter which). Not sure how I would download the files to the connecting computer though. I would like the tunnel to be secured, preferably, with a username/password. I'm open to using alternative software but I'm looking for unintrusive, simple command line stuff because I don't want to install a lot on this computer. Thanks

  Read the article

• Troubles doing transparent proxy for virtual machines

  - by Dan H

  Hi iptables gurus. First here is the basic topology: Internet | Gateway | Workstation---eth0---virbr0 | +-----+-----+ | | | vm1 vm2 vm3 I need to test a traffic analyzer running on my workstation, listening on some port (say 8990) on eth0. The rule [I think] I want is "any packets leaving virbr0 going anywhere to port 80 must instead go to port 8990 on eth0". My software running on port 8990 does its own check of the NAT packet mangling to push the packets through after it inspects them. I've been banging my head on this, with different variants of: iptables -t nat -A PREROUTING -i virbr0 -p tcp --dport 80 -j DNAT \ --to 10.0.0.10:8990 And I've tried the more generic method of using the mangle table with --set-mark and ip rule add fwmark, but I'm not getting it. I guess what's confusing me is that everything runs on the same box. Thanks for any guidance.

  Read the article

• Network Monitoring Tool Recommendation

  - by user42801

  Hello, My company is looking for a monitoring app/tool that would allow us to capture and graph statistics on network performance. As a starting point, we would like to ping remote host(s) and gateway(s) from several of our servers, grab an average of the ping times from each of our servers to the remote host(s), and then graph it (preferably in a central location). Also, we would like to be able to graph the results for time frames as short as a week to as long as 6 months. It is reasonable to expect that we would ask more of the selected monitoring app/tool as we come up with other key network performance indicators in the future. So an app with great flexibility and features would be ideal. Upon first glance, Cacti looks like it might be a fit. Any other recommendations? Thanks in advance for any input.

  Read the article

• Python: how to calculate data received and send between two ipaddresses and ports [closed]

  - by ramdaz

  I guess it's socket programming. But I have never done socket programming expect for running the tutorial examples while learning Python. I need some more ideas to implement this. What I specifically need is to run a monitoring program of a server which will poll or listen to traffic being exchange from different IPs across different popular ports. For example, how do I get data received and sent through port 80 of 192.168.1.10 and 192.168.1.1 ( which is the gateway). I checked out a number of ready made tools like MRTG, Bwmon, Ntop etc but since we are looking at doing some specific pattern studies, we need to do data capturing within the program. Idea is to monitor some popular ports and do a study of network traffic across some periods and compare them with some other data. We would like to figure a way to do all this with Python....

  Read the article

< Previous Page | 76 77 78 79 80 81 82 83 84 85 86 87  | Next Page >