Search Results

Search found 3935 results on 158 pages for 'garreth 00'.

Page 97/158 | < Previous Page | 93 94 95 96 97 98 99 100 101 102 103 104  | Next Page >

• SSD and intel i5 lagging

  - by Marek Javurek

  my "new" notebook has some really wierd lags during work, youtube video etc etc... Sometimes it has bluescreen during booting, sometimes after reboot. All my drivers are updated and SSD firmware too. this is my notebook parameters: Operating System MS Windows 7 64-bit SP1 CPU Intel Core i5 @ 2.40GHz: 57 °C Sandy Bridge 32nm Technology RAM 8,00 GB Dual-Channel DDR3 @ 665MHz (9-9-9-24) Motherboard LENOVO 12985VG (CPU): 58 °C Graphics SyncMaster (1680x1050@60Hz) AMD Radeon HD 6630M Series (Lenovo) Hard Drives 125GB Crucial M4-CT128M4SSD1 ATA Device (SATA-SSD) full specs here: http://speccy.piriform.com/results/Khr265gWVgk6vKTMrhdfhlS

  Read the article

• Ubuntu with KVM guest VM and broken bridges

  - by MadPsy

  I have an Ubuntu box with a KVM guest VM running. They use bridging so the guest VM attaches to the physical network of its host. The guest VM has 2 NICs in 2 different bridges. First NIC of the VM is tap5 and is in bridge br0 br0 8000.46720f5c572e no eth0.500 tap5 Second NIC of the VM is tap2 and is in bridge br100 br100 8000.76ad2fc96661 no eth0.100 eth0.101 eth0.103 eth0.104 eth0.105 tap2 On the host, br0 has an IP and br100 does not 21: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 46:72:0f:5c:57:2e brd ff:ff:ff:ff:ff:ff inet 192.168.100.4/24 brd 192.168.10.255 scope global br0 inet6 fe80::d6ae:52ff:febe:777/64 scope link valid_lft forever preferred_lft forever On the guest, its eth0 and eth1 interfaces both have IP addresses 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:3e:61:fb:7a:da brd ff:ff:ff:ff:ff:ff inet 192.168.100.6/24 brd 192.168.100.255 scope global eth0 inet6 fe80::23e:61ff:fefb:7ada/64 scope link valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:3e:61:fb:7a:ea brd ff:ff:ff:ff:ff:ff inet 172.16.50.129/25 brd 172.16.50.255 scope global eth1 inet6 fe80::23e:61ff:fefb:7aea/64 scope link valid_lft forever preferred_lft forever On the guest VM, a tcpdump of its eth1 interface (tap2) shows traffic from its eth0 interface (tap5), as if the 2 bridges are themselves bridged. This means any interface on br100 is now bridged across to br0 - which is completely broken. root@chillispot:~# tcpdump -c 1 -n -v -i eth1 net 192.168.100.0/24 tcpdump: listening on eth1, link-type EN10MB (Ethernet), capture size 65535 bytes 16:31:24.175583 IP (tos 0x0, ttl 64, id 48054, offset 0, flags [DF], proto TCP (6), length 148) 192.168.100.6.22 > 192.168.100.4.59505: Flags [P.], cksum 0x6c2b (correct), seq 1056321648:1056321744, ack 398642983, win 1700, options [nop,nop,TS val 197473436 ecr 200655363], length 96 What could be bridging the 2 bridges, except the guest VM (which is a stock Ubuntu install)? I am at a complete loss! Thanks.

  Read the article

• mysql-proxy got error which cause it to crash

  - by nonus25

  I got that message and i dont know what it is means: Oct 21 12:24:26 lex mysql-proxy: 2013-10-21 12:24:26: ((error)) last message repeated 98 times Oct 21 12:24:26 lex mysql-proxy: 2013-10-21 12:24:26: ((error)) network-mysqld-packet.c.596: COM_(0x04) should not be (OK|ERR|NULL), got: 00 Oct 21 12:24:26 lex kernel: [4163416.207121] mysql-proxy[14271] trap int3 ip:7ff96e8a4313 sp:7fffb9086ad0 error:0 Any idea what can be the cause of it ?

  Read the article

• SPS 2007 backup webparts etc.

  - by elhombre

  Hi all I would like to backup my hole Share-point 2007 stuff. But as I read on http://searchwinit.techtarget.com/generic/0,295582,sid1_gci1319629,00.html Share-point isn't able to backup all content for an disaster restore. Following can't be backuped * Third-party or custom Web parts * SharePoint site definitions and XML files * SharePoint .aspx template pages * SharePoint script files Know I want to know how can I backup these items, especially web parts!

  Read the article

• SSL connection error during handshake on Windows Server 2008 R2

  - by Thomas

  I have a Windows 2008 R2 Server that runs a HTTPS Tunneling service. The software uses a certificate that is provided via the Windows certificate store. The certificate is located in the local computer private certificates. It supports server and client authentication with signing and keyencipherment. Cert chain The certificate chain looks fine. It's a Thawte SSL123 certificate. Thawte Premium Server CA (SHA1) [?e0 ab 05 94 20 72 54 93 05 60 62 02 36 70 f7 cd 2e fc 66 66] thawte Primary Root CA [?1f a4 90 d1 d4 95 79 42 cd 23 54 5f 6e 82 3d 00 00 79 6e a2] Thawte DV SSL CA [3c a9 58 f3 e7 d6 83 7e 1c 1a cf 8b 0f 6a 2e 6d 48 7d 67 62] Server certificate Issues Most browsers accept the certificate without any warning. But IE 7 on Windows XP SP3 and Opera 12 on OSX just report an connection error. Opera complains: Secure connection: fatal error (552) https://www.example.com/ Opera was not able to connect to the server, because the server does not communicate via any secure protocol known to Opera. A connection test using openssl s_client -connect www.example.com:443 -state says: CONNECTED(00000003) SSL_connect:before/connect initialization SSL_connect:SSLv2/v3 write client hello A 52471:error:140790E5:SSL routines:SSL23_WRITE:ssl handshake failure:/SourceCache/OpenSSL098/OpenSSL098-35.1/src/ssl/s23_lib.c:182: ssldump -aAHd host www.example.com during curl https://www.example.com/ reports: New TCP connection #1: localhost(53302) <-> www.example.com(443) 1 1 0.0235 (0.0235) C>SV3.1(117) Handshake ClientHello Version 3.1 random[32]= 50 77 56 29 e8 23 82 3b 7f e0 ae 2d c1 31 cb ac 38 01 31 85 4f 91 39 c1 04 32 a6 68 25 cd a0 c1 cipher suites Unknown value 0x39 Unknown value 0x38 Unknown value 0x35 TLS_DHE_RSA_WITH_3DES_EDE_CBC_SHA TLS_DHE_DSS_WITH_3DES_EDE_CBC_SHA TLS_RSA_WITH_3DES_EDE_CBC_SHA Unknown value 0x33 Unknown value 0x32 Unknown value 0x2f Unknown value 0x9a Unknown value 0x99 Unknown value 0x96 TLS_RSA_WITH_RC4_128_SHA TLS_RSA_WITH_RC4_128_MD5 TLS_DHE_RSA_WITH_DES_CBC_SHA TLS_DHE_DSS_WITH_DES_CBC_SHA TLS_RSA_WITH_DES_CBC_SHA TLS_DHE_RSA_EXPORT_WITH_DES40_CBC_SHA TLS_DHE_DSS_EXPORT_WITH_DES40_CBC_SHA TLS_RSA_EXPORT_WITH_DES40_CBC_SHA TLS_RSA_EXPORT_WITH_RC2_CBC_40_MD5 TLS_RSA_EXPORT_WITH_RC4_40_MD5 Unknown value 0xff compression methods unknown value NULL 1 0.0479 (0.0243) S>C TCP FIN 1 0.0481 (0.0002) C>S TCP FIN Thawte provides two Java based SSL Checkers. The Legacy Thawte SSL Certificate Installation Checker and the sslToolBox. Both validate the certificate under Windows XP but report connection errors under OSX and Windows 2008 R2.

  Read the article

• Linksys WiFi usb dongle and linux woes

  - by MrStatic

  I have a Linksys WUSB54GC usb dongle and I have exhausted every thing I know about making this thing work in linux. I am using Fedora 13. Since it is not ready I can not view any networks. Any ideas would be great. tail of the system log Jun 2 20:14:35 localhost kernel: usb 1-7: new high speed USB device using ehci_hcd and address 8 Jun 2 20:14:35 localhost kernel: usb 1-7: New USB device found, idVendor=1737, idProduct=0077 Jun 2 20:14:35 localhost kernel: usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Jun 2 20:14:35 localhost kernel: usb 1-7: Product: 802.11 g WLAN Jun 2 20:14:35 localhost kernel: usb 1-7: Manufacturer: Ralink Jun 2 20:14:35 localhost kernel: usb 1-7: SerialNumber: 1.0 Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::radio Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::assoc Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::quality Jun 2 20:14:35 localhost NetworkManager[1367]: <info> found WiFi radio killswitch rfkill3 (at /sys/devices/pci0000:00/0000:00:1d.7/usb1/1-7/1-7:1.0/ieee80211/phy3/rfkill3) (driver <unknown>) Jun 2 20:14:35 localhost kernel: rt2800usb 1-7:1.0: firmware: requesting rt2870.bin Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): driver supports SSID scans (scan_capa 0x01). Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): new 802.11 WiFi device (driver: 'rt2800usb' ifindex: 6) Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/4 Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): now managed Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): device state change: 1 -> 2 (reason 2) Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): bringing up device. Jun 2 20:14:35 localhost kernel: ADDRCONF(NETDEV_UP): wlan0: link is not ready Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): preparing device. Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): deactivating device (reason: 2). Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): supplicant interface state: starting -> ready Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): device state change: 2 -> 3 (reason 42) [root@localhost log]# iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg Mode:Managed Access Point: Not-Associated Tx-Power=8 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on

  Read the article

• Adaptec 5805 not recognized after reboot

  - by Rakedko ShotGuns

  After rebooting the system, the controller is not recognized. It only works if the computer is shut down and turned off. I have recently updated the firmware to "Adaptec RAID 5805 Firmware Build 18948". How do I fix the problem? Configuration summary --------------------------- 1. Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priority High Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1

  Read the article

• What are the ideal settings for a Belkin WiFi Router to connect to an iPhone? [closed]

  - by user34833

  The Belkin Router (F5D8235-4 v2000) has numerous options in the setup. These are the current settings: Wireless On SSID Buster's Special Security Type WPA Encryption Type TKIP WLAN MAC Address 00:22:75:B3:58:38 WPS Enabled Guest Access Disabled SSID Belkin_N+_Guest Password/PSK NotThatSillyYet :) The iPhone is a 3g with 16GB it has no problems connecting to public networks like libraries or restaurants. But currently it won't connect to my home WiFi. Thanks for your time and help. Paul

  Read the article

• OpenVPN bridged not pinging beyond openvpn server on Ubuntu/Windows 2003

  - by ani

  I set up an OpenVPN server using Ubuntu and a windows server 2003 client to interconnect two networks between two different offices. They can now ping each other, but the rest of the network cannot be contacted by the windows client. Office 1 has internal network of: 192.168.0.0 255.255.240.0 Office 2 has internal network of: 192.168.16.0 255.255.255.0 And the configuration files are: Server.conf port 1194 --script-security 2 up "/etc/openvpn/up.sh br0" down "/etc/openvpn/down.sh br0" # TCP or UDP server? ;proto tcp proto udp dev tap0 ;dev tun ca ca.crt cert openvpn.crt key openvpn.key dh dh1024.pem ifconfig-pool-persist ipp.txt server-bridge 192.168.0.59 255.255.240.0 192.168.6.72 192.168.6.75 push "route 192.168.0.0 255.255.240.0" push "dhcp-option DNS 192.168.0.2" push "dhcp-option DOMAIN testeers.local" keepalive 10 120 tls-auth ta.key 0 # This file is secret comp-lzo user nobody group nogroup persist-key persist-tun log /var/log/openvpn/openvpn.log status /var/log/openvpn-status.log verb 3 Client Config file client dev tap ;dev tun --script-security 2 ;proto tcp proto udp remote 1xx.2xx.xxx.124 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert admin-VAIO.crt key admin-VAIO.key ns-cert-type server tls-auth ta.key 1 comp-lzo verb 3 Ifconfig on the server now shows the following: br0 Link encap:Ethernet HWaddr 00:50:56:8b:1a:49 inet addr:192.168.0.59 Bcast:192.168.15.255 Mask:255.255.240.0 inet6 addr: fe80::250:56ff:fe8b:1a49/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1081860 errors:0 dropped:1358 overruns:0 frame:0 TX packets:242385 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:76600615 (76.6 MB) TX bytes:64474575 (64.4 MB) eth0 Link encap:Ethernet HWaddr 00:50:56:8b:1a:49 UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:1144125 errors:0 dropped:7172 overruns:0 frame:0 TX packets:252486 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:109893729 (109.8 MB) TX bytes:66372620 (66.3 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:67865 errors:0 dropped:0 overruns:0 frame:0 TX packets:67865 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5183276 (5.1 MB) TX bytes:5183276 (5.1 MB) tap0 Link encap:Ethernet HWaddr 32:4f:42:11:b7:c5 inet6 addr: fe80::304f:42ff:fe11:b7c5/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:3329 errors:0 dropped:0 overruns:0 frame:0 TX packets:215472 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:373205 (373.2 KB) TX bytes:17465832 (17.4 MB)

  Read the article

• Can't get my Raspberry Pi to keep a static IP

  - by JonnyIrving

  I recently got given a Raspberry Pi and I would like to be able to remote into it using puTTy from my laptop so I don't have to sit next to my tv with a keyboard and mouse to use it. I am able to get a puTTy session going when I know the IP address that my router has given the Pi on each session but it keeps changing on each reboot as I would expect. So I followed a number if instruction to go about configuring the RPi to keep a static IP address. This involved changing the file at '/etc/netwrok/interfaces' which now contains (password removed): auto lo iface lo inet loopback iface eth0 inet static address 192.168.1.82 netmask 255.255.255.0 gateway 192.168.1.254 auto wlan0 allow-hotplug wlan0 iface wlan0 inet dhcp wpa-ssid "BeBoxD304BF" wpa-psk "**********" Despite this however, each time I reboot my RPi it gives me a new dynamic IP address still. I also noticed that in the 'ifconfig' output below that the details of the eth0 doesn't contain IP details for inet addr, Bcast or Mask which have been present in all other examples I have seen online. eth0 Link encap:Ethernet HWaddr b8:27:eb:b5:95:da UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 00:87:c6:00:33:77 inet addr:192.168.1.83 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:918 errors:0 dropped:0 overruns:0 frame:0 TX packets:277 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 Also I'm not sure if this is relevant but it can't hurt! The file at '/etc/resolv.conf' contains: domain config search config nameserver 192.168.1.254 ..I heard it might mean something on one of the pages I was looking at. I would be very grateful for any help with this. I have tried everything I can think of and would really like to get this working this weekend so I can use it from work.

  Read the article

• Is memcache impacting my performence negatively?

  - by iTech

  I am using pressflow 6 and NewRelic seems to suggest that memcache is infact hurting performance as shown below : My settings.php file : # Varnish reverse proxy on localhost $conf['reverse_proxy'] = TRUE; $conf['reverse_proxy_addresses'] = array('127.0.0.1'); # Memcached configuration $conf['cache_inc'] = './sites/all/modules/memcache/memcache.inc'; $conf['memcache_servers'] = array( '127.0.0.1:11211' => 'default', ); ### END Mercury settings written on 2011-11-01T07:12:49-04:00

  Read the article

• Calculate the sum of numbers in column G of MS Excel sheet

  - by rohit

  When I calculate the sum of numbers in the column G of a Microsoft Excel spreadsheet by using the formula =SUM(G1,G31) ,column G32 prints the date (0-Jan-00). Is there any way in which the sum of numbers in the column G can be calculated? I am using MS excel 2003 SP3.

  Read the article

• Suspected network performance issue on VirtualBox Ubuntu guest on Win7 host

  - by Adam

  I set up Ubuntu 12.04 in VirtualBox on the Win7 machine I was allocated on my new project. I am running Java, Eclipse, Tomcat to develop a large data-intensive application and I noticed that this application runs at half the speed of my colleague's identical machine, where he runs it all under Windows. I think I have narrowed down the performance issue to the network, after comparing and equalising all the Java VM settings with my colleague. Is there a ping test I can do or some other network diagnostic test to flag up any problems? To give some background, the network performance is confusing. Running a network speed test to my colleague's machine with iperf shows speeds of 6 Mb/s from my Ubuntu guest, and 90 Mb/s from the win7 host. Large downloads, e.g. the Java SDK, come down at about 1.2 MB/s on both the guest and the host. Pings are sub-1ms on the host, but 1.5ms on the guest. I also did a broadband speed test, and got 10Mb/s download speed on both, but the host has an upload speed of 10Mb/s but the guest only uploads at 3Mb/s. I've been trying to diagnose any MTU problems with ping -M do to identify any kind of packet fragmentation problem but it's progressing very slow because I don't have much experience in this area. From what I read on other people's networking issues with VB and Linux guests on Win7 hosts, I should be able to get the speed on the guest up to the same level as the host. I installed a fresh VM with Ubuntu again to see if I'd foobar'd it somehow, but I'm getting the same readings with iperf on the virgin installation. My setup is: Adapter 1: Intel PRO/1000 MT Desktop (NAT) Adapter 2: ditto (host-only adapter) eth0 Link encap:Ethernet HWaddr 08:00:27:0b:76:bf inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe0b:76bf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:86236 errors:0 dropped:0 overruns:0 frame:0 TX packets:49369 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:69163946 (69.1 MB) TX bytes:3530535 (3.5 MB) eth2 Link encap:Ethernet HWaddr 08:00:27:a3:26:b8 inet addr:192.168.56.101 Bcast:192.168.56.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fea3:26b8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:59 errors:0 dropped:0 overruns:0 frame:0 TX packets:57 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9148 (9.1 KB) TX bytes:7648 (7.6 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:701 errors:0 dropped:0 overruns:0 frame:0 TX packets:701 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:66321 (66.3 KB) TX bytes:66321 (66.3 KB)

  Read the article

• Routing table with two NIC adapters in libvirt/KVM

  - by lzap

  I created a virtual NAT network (192.168.100.0/24 network) in my libvirt and new guest with two interfaces - one in this network, one as bridged (10.34.1.0/24 network) to the local LAN. The reason for that is I need to have my own virtual network for my DHCP/TFTP/DNS testing and still want to access my guest externally from my LAN. On both networks I have working DHCP, both giving them IP addresses. When I setup NAT port forwarding (e.g. for ssh), I can connect to the eth0 (virtual network), everything is fine. But when I try to access the eth1 via bridged interface, I have no response. I guess I have problem with my routing table - outgoing packets are routed to the virtual NAT network (which has access to the machine I am connecting from - I can ping it). But I am not sure if this setup is correct. I think I need to add something to my routing table. # ifconfig eth0 Link encap:Ethernet HWaddr 52:54:00:B4:A7:5F inet addr:192.168.100.14 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:feb4:a75f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16468 errors:0 dropped:27 overruns:0 frame:0 TX packets:6081 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:22066140 (21.0 MiB) TX bytes:483249 (471.9 KiB) Interrupt:11 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 52:54:00:DE:16:21 inet addr:10.34.1.111 Bcast:10.34.1.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fede:1621/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:189 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4911 (4.7 KiB) TX bytes:9 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.34.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1003 0 0 eth1 0.0.0.0 192.168.100.1 0.0.0.0 UG 0 0 0 eth0 Network I am trying to connect from is different than network the hypervisor is connected to: 10.36.0.0. But it is accessible from that network. So I tried to add new route rule: route add -net 10.36.0.0 netmask 255.255.0.0 dev eth1 And it is not working. I thought setting correct interface would be sufficient. What is needed to get my packets coming through?

  Read the article

• Determine hostname of connected ethernet switch

  - by Beastcraft

  I've a bonding on two interfaces. I'd like to monitor wether they are connected to different switches (the switches have hostnames). ethX should be connected to switchX and ethY to switchY. Currently I'm checking this with following command: tcpdump -vv -s0 -i ethX ether host 01:00:0c:cc:cc:cc After a minute it prints out the hostname (and much more information) from the switch. Are there any other solutions to monitor this? Greeting

  Read the article

• Unable to connect to Linux (Virtual OS-vmware) through Putty on Windows

  - by RBA

  Hi, I want to access my Linux box (Virtual OS) through Putty on Windows using Run command: putty -ssh -P 22 192.168.171.130,,, but it is returning an error message, not able to connect. But few days back I was able to connect it today. But not now. Why?? Windows IP Configuration Host Name . . . . . . . . . . . . : rba7791fd466 Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet1 Physical Address. . . . . . . . . : 00-50-56-C0-00-01 Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.234.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Dell Wireless 1395 WLAN Mini-Card Physical Address. . . . . . . . . : 00-24-2B-60-A0-88 Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 10.0.0.2 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.0.0.1 DHCP Server . . . . . . . . . . . : 10.0.0.1 DNS Servers . . . . . . . . . . . : 10.0.0.1 Lease Obtained. . . . . . . . . . : Friday, August 28, 2009 4:11:09 AM Lease Expires . . . . . . . . . . : Saturday, August 29, 2009 4:11:09 AM Ubuntu Configuration eth0 inet addr:192.168.171.130

  Read the article

• Can only bring up one of two interfaces

  - by mstaessen

  I'm having a bizarre issue with my HP Proliant DL 360 G4p server. It has two gigabit ethernet interfaces but I can bring up only one of them. This is starting to freak me out and that's why I turned here. I'm running the x64 ubuntu 11.10 server edition. lshw -c network shows that the second interface is disabled. I have no idea why ans how to enable it. $ sudo lshw -c network *-network:0 description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 logical name: eth0 version: 10 serial: 00:18:71:e3:6d:26 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=5704-v3.27b, ASFIPMIc v2.36 ip=10.48.8.x latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:25 memory:fdf70000-fdf7ffff *-network:1 DISABLED description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2.1 bus info: pci@0000:02:02.1 logical name: eth1 version: 10 serial: 00:18:71:e3:6d:25 capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=5704-v3.27b latency=64 link=no mingnt=64 multicast=yes port=twisted pair resources: irq:26 memory:fdf60000-fdf6ffff If I try to ifup eth1, then I get $ sudo ifup eth1 Ignoring unknown interface eth1=eth1. I figured that's what happens when there is no eth1 listed in /etc/network/interfaces. But when I add the configuration for eth1, I still can't ifup. $ sudo ifup eth1 RTNETLINK answers: File exists Failed to bring up eth1. I've also tried ifconfig eth1 up but without any result. For clarity, I have added a masked version of /etc/network/interfaces. I don't think it is the cause of the problem though. $ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.48.8.x netmask 255.255.255.y network 10.48.8.z broadcast 10.48.8.t gateway 10.48.8.u auto eth1 iface eth1 inet static address 193.190.253.x netmask 255.255.255.y network 193.190.253.z broadcast 193.190.253.t gateway 193.190.253.u I really need some help fixing this. It's driving me crazy. Thanks.

  Read the article

• PHP ssh2_fingerprint() does not match ssh-keygen -lf id_rsa.pub

  - by Justin

  I am using the lib ssh2 module with PHP and calling the function ssh2_fingerprint() to get the keys fingerprint. According to all resources on the internet, I can get the fingerprint of a public key by executing: ssh-keygen -lf id_rsa.pub Which outputs something like: 2048 d4:41:3b:45:00:49:4e:fc:2c:9d:3a:f7:e6:6e:bf:e7 id_rsa.pub (RSA) However, when I call ssh2_fingerprint($connection, SSH2_FINGERPRINT_HEX) in PHP with the same public key I get: dddddba52352e5ab95711c10fdd56f43 Shouldn't they match? What am I missing?

  Read the article

• Can not get sound over hdmi in kubuntu 9.10

  - by user32509

  I have used a hdmi cable to connect my lcd (which is connected with my speakers) with my nvida 275 gtx grafic card. I can not get the sound output to work. The hardware itself is working probably - I tested it under windows. Currently I am running Kubuntu 9.10 64 with Nvidia 190.53. The sound output worked fine before I installed the hdmi connection. (German output - i can change it, if you tell me how :)) aplay -l **** Liste von PLAYBACK Geräten **** Karte 0: Intel [HDA Intel], Gerät 0: ALC889A Analog [ALC889A Analog] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 Karte 0: Intel [HDA Intel], Gerät 1: ALC889A Digital [ALC889A Digital] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 aplay -L front:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog Front speakers surround40:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers iec958:CARD=Intel,DEV=0 HDA Intel, ALC889A Digital IEC958 (S/PDIF) Digital Audio Output null Discard all samples (playback) or generate zero samples (capture) pulse Playback/recording through the PulseAudio sound server And i disabled mute in kmix an all channels :) Edit: lspci -v ... 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) Subsystem: Giga-byte Technology Device a022 Flags: bus master, fast devsel, latency 0, IRQ 22 Memory at ea400000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel <?> Capabilities: [130] Root Complex Link <?> Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel ... cat /proc/asound/version Advanced Linux Sound Architecture Driver Version 1.0.20. lsmod | grep snd_hda_intel snd_hda_intel 31880 2 snd_hda_codec 87584 2 snd_hda_codec_realtek,snd_hda_intel snd_pcm 93160 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss snd 77096 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device snd_page_alloc 10928 2 snd_hda_intel,snd_pcm I think I am missing the something-hdmi module? Is there such a thing?

  Read the article

• Restart works like shutdown (Windows 7).

  - by Cogito84

  I have a problem with restarting my PC, it happend couple days ago, and now restart works same as shutdown, even when I tried to make my own shortcut(Shutdown.exe -r -t 00), it just shutdowns. Any idea how to fix that ?

  Read the article

• How to add a font to the Cmd window choices in Windows 7 64-bit?

  - by Mark Ransom

  I tried following the procedure outlined in this previous answer and it doesn't work: http://superuser.com/a/5079/2366 Specifically I'm trying to add Lucida Sans Typewriter Regular to the choices of Consolas and Lucida Console that the Cmd window currently allows. Lucida Console is in registry key "0" and Consolas is in registry key "00", so I'm adding key "000" but it's not affecting the available choices in the Font tab under Properties, even after rebooting the system. P.S. I also tried adding Courier New to the choices and it shows up, but appears to select Italic instead.

  Read the article

• ffmpeg - join / merge on top of each other

  - by AisIceEyes

  I'm trying to join together two videos on top of each other. I already did these two ffmpeg commands ffmpeg -i 2_Out_of_Control.VOB -aspect 16:9 \ -vf "yadif=0:-1:0,crop=w=714:h=476:x=6:y=0,scale=1280:720,boxblur=lp=13" \ -c:v libx264 -preset medium \ -c:a copy \ '2(blurred)Out_of_Control.mp4' ffmpeg -i 2_Out_of_Control.VOB \ -vf "yadif=0:-1:0,crop=w=714:h=476:x=6:y=0,scale=1080:720" \ -c:v libx264 -preset medium \ -c:a copy \ '2(clear)Out_of_Control.mp4' I'm currently stuck on making the "clear" version on top of the "blurred" version. I'm not sure how to do that. Can anybody help please? Been googling for around 2 days already. Only achieved it by using OpenShot but yeah, would prefer if there is an ffmpeg command to merge the two videos on top of each other. Edit: I want the "clear" video to be at the center at the top of the "blurred" video Edit2: console output would be the same as above: ffmpeg -i 2(blurred)Out_of_Control.mp4 \ -i 2(clear)Out_of_Control.mp4 \ -aspect 16:9 \ -vf <just something that will join the two together: the blurred at the bottom, clear at top that is centered> \ -c:v libx264 -preset medium \ -c:a copy \ '2_Out_of_Control_VOB.mp4' Edit3: here is the output when I used ffmpeg -i 2_Out_of_Control.VOB $ ffmpeg -i 2_Out_of_Control.VOB ffmpeg version git-2013-10-03-c7fe2a3 Copyright (c) 2000-2013 the FFmpeg developers built on Oct 4 2013 05:22:06 with gcc 4.6 (Ubuntu/Linaro 4.6.3-1ubuntu5) configuration: --prefix=/home/username/ffmpeg_build --extra-cflags=-I/home/username/ffmpeg_build/include --extra-ldflags=-L/home/username/ffmpeg_build/lib --bindir=/home/username/bin --extra-libs=-ldl --enable-gpl --enable-libass --enable-libfdk-aac --enable-libmp3lame --enable-libopus --enable-libtheora --enable-libvorbis --enable-libvpx --enable-libx264 --enable-nonfree --enable-x11grab libavutil 52. 46.100 / 52. 46.100 libavcodec 55. 34.100 / 55. 34.100 libavformat 55. 19.100 / 55. 19.100 libavdevice 55. 3.100 / 55. 3.100 libavfilter 3. 88.101 / 3. 88.101 libswscale 2. 5.100 / 2. 5.100 libswresample 0. 17.103 / 0. 17.103 libpostproc 52. 3.100 / 52. 3.100 Input #0, mpeg, from '2_Out_of_Control.VOB': Duration: 00:05:00.01, start: 0.500000, bitrate: 4574 kb/s Stream #0:0[0x1e0]: Video: mpeg2video (Main), yuv420p(tv, smpte170m), 720x480 [SAR 8:9 DAR 4:3], max. 9334 kb/s, 29.97 fps, 29.97 tbr, 90k tbn, 59.94 tbc Stream #0:1[0x80]: Audio: ac3, 48000 Hz, stereo, fltp, 384 kb/s At least one output file must be specified $

  Read the article

• What is the best way to slide a panel in WPF?

  - by Kris Erickson

  I have a fairly simple UserControl that I have made (pardon my Xaml I am just learning WPF) and I want to slide the off the screen. To do so I am animating a translate transform (I also tried making the Panel the child of a canvas and animating the X position with the same results), but the panel moves very jerkily, even on a fairly fast new computer. What is the best way to slide in and out (preferably with KeySplines so that it moves with inertia) without getting the jerkyness. I only have 8 buttons on the panel, so I didn't think it would be too much of a problem. Here is the Xaml I am using, it runs fine in Kaxaml, but it is very jerky and slow (as well as being jerkly and slow when run compiled in a WPF app). <UserControl xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" Width="1002" Height="578"> <UserControl.Resources> <Style TargetType="Button"> <Setter Property="Control.Padding" Value="4"/> <Setter Property="Control.Margin" Value="10"/> <Setter Property="Control.Template"> <Setter.Value> <ControlTemplate TargetType="Button"> <Grid Name="backgroundGrid" Width="210" Height="210" Background="#00FFFFFF"> <Grid.BitmapEffect> <BitmapEffectGroup> <DropShadowBitmapEffect x:Name="buttonDropShadow" ShadowDepth="2"/> <OuterGlowBitmapEffect x:Name="buttonGlow" GlowColor="#A0FEDF00" GlowSize="0"/> </BitmapEffectGroup> </Grid.BitmapEffect> <Border x:Name="background" Margin="1,1,1,1" CornerRadius="15"> <Border.Background> <LinearGradientBrush StartPoint="0,0" EndPoint="0,1"> <LinearGradientBrush.GradientStops> <GradientStop Offset="0" Color="#FF0062B6"/> <GradientStop Offset="1" Color="#FF0089FE"/> </LinearGradientBrush.GradientStops> </LinearGradientBrush> </Border.Background> </Border> <Border Margin="1,1,1,0" BorderBrush="#FF000000" BorderThickness="1.5" CornerRadius="15"/> <ContentPresenter HorizontalAlignment="Center" Margin="{TemplateBinding Control.Padding}" VerticalAlignment="Center" Content="{TemplateBinding ContentControl.Content}" ContentTemplate="{TemplateBinding ContentControl.ContentTemplate}"/> </Grid> </ControlTemplate> </Setter.Value> </Setter> </Style> </UserControl.Resources> <Canvas> <Grid x:Name="Panel1" Height="578" Canvas.Left="0" Canvas.Top="0"> <Grid.RenderTransform> <TransformGroup> <TranslateTransform x:Name="panelTranslate" X="0" Y="0"/> </TransformGroup> </Grid.RenderTransform> <Grid.RowDefinitions> <RowDefinition Height="287"/> <RowDefinition Height="287"/> </Grid.RowDefinitions> <Grid.ColumnDefinitions> <ColumnDefinition x:Name="Panel1Col1"/> <ColumnDefinition x:Name="Panel1Col2"/> <ColumnDefinition x:Name="Panel1Col3"/> <ColumnDefinition x:Name="Panel1Col4"/> <!-- Set width to 0 to hide a column--> </Grid.ColumnDefinitions> <Button x:Name="Panel1Product1" Grid.Column="0" Grid.Row="0" HorizontalAlignment="Center" VerticalAlignment="Center"> <Button.Triggers> <EventTrigger RoutedEvent="Button.Click" SourceName="Panel1Product1"> <EventTrigger.Actions> <BeginStoryboard> <Storyboard> <DoubleAnimation BeginTime="00:00:00.6" Duration="0:0:3" From="0" Storyboard.TargetName="panelTranslate" Storyboard.TargetProperty="X" To="-1000"/> </Storyboard> </BeginStoryboard> </EventTrigger.Actions> </EventTrigger> </Button.Triggers> </Button> <Button x:Name="Panel1Product2" Grid.Column="0" Grid.Row="1" HorizontalAlignment="Center" VerticalAlignment="Center"/> <Button x:Name="Panel1Product3" Grid.Column="1" Grid.Row="0" HorizontalAlignment="Center" VerticalAlignment="Center"/> <Button x:Name="Panel1Product4" Grid.Column="1" Grid.Row="1" HorizontalAlignment="Center" VerticalAlignment="Center"/> <Button x:Name="Panel1Product5" Grid.Column="2" Grid.Row="0" HorizontalAlignment="Center" VerticalAlignment="Center"/> <Button x:Name="Panel1Product6" Grid.Column="2" Grid.Row="1" HorizontalAlignment="Center" VerticalAlignment="Center"/> <Button x:Name="Panel1Product7" Grid.Column="3" Grid.Row="0" HorizontalAlignment="Center" VerticalAlignment="Center"/> <Button x:Name="Panel1Product8" Grid.Column="3" Grid.Row="1" HorizontalAlignment="Center" VerticalAlignment="Center"/> </Grid> </Canvas> </UserControl>

  Read the article

• MSBuild cannot find SGen when compiling a solution

  - by Jaxidian

  I've looked at several other SGen-related questions on here and either their answers don't apply or their answers don't fix this for me. I have installed several SDKs to fix this issue with no luck. Reference types should not be changed since this is the only place this is a problem. Once suggestion is to put SGen.exe into the C:\Windows\Microsoft.NET\Framework\v3.5 folder, but that's not been done on the box where this is not a problem. In this scenario, SGen.exe actually exists and is right where it's supposed to be, but MSBuild still is having issues with finding it for some reason! Background: We have a NAnt script that automates our builds. In this scenario, NAnt is calling MSBuild and MSBuild is generating the error claiming to be unable to find SGen. The project is .NET 3.5-based. I have my primary dev environment (64-bit Vista Ultimate) where the script works perfectly and I am attempting to duplicate it in a VM (64-bit Win 7 Ultimate). I THINK I have everything to the point where I should be good-to-go but this fails on the Win7 box (works perfectly on the Vista box). I have done some comparisons between the two boxes and they both look identical in this regard, but it still fails. For example, the HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\.NETFramework's sdkInstallRootv2.0 value is set to C:\Program Files\Microsoft.NET\SDK\v2.0 64bit\ on both machines. In both machines, SGen.exe is in that path's bin subdirectory. NAnt Script: <target name="report-installer" depends="fail-if-environment-not-set"> <exec program="MSBuild.exe" basedir="${framework35.directory}"> <arg value="${tools.directory.current}\ReportInstaller\ReportInstaller.sln" /> <arg value="/p:Configuration=${buildconfiguration.current}" /> </exec> </target> The error message I get is this: report-installer: [exec] Microsoft (R) Build Engine Version 3.5.30729.4926 [exec] [Microsoft .NET Framework, Version 2.0.50727.4927] [exec] Copyright (C) Microsoft Corporation 2007. All rights reserved. [exec] [exec] Build started 4/8/2010 11:28:23 AM. [exec] Project "C:\Projects\Production\Tools\ReportInstaller\ReportInstaller.sln" on node 0 (default targets). [exec] Building solution configuration "Release|Any CPU". [exec] Project "C:\Projects\Production\Tools\ReportInstaller\ReportInstaller.sln" (1) is building "C:\Projects\Production\Tools\ReportInstaller\ReportInstaller.csproj" (2) on node 0 (default targets). [exec] Could not locate the .NET Framework SDK. The task is looking for the path to the .NET Framework SDK at the location specified in the SDKInstallRootv2.0 value of the registry key HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\.NETFramework. You may be able to solve the problem by doing one of the following: 1.) Install the .NET Framework SDK. 2.) Manually set the above registry key to the correct location. [exec] CoreCompile: [exec] Skipping target "CoreCompile" because all output files are up-to-date with respect to the input files. [exec] C:\Windows\Microsoft.NET\Framework\v2.0.50727\Microsoft.Common.targets(1902,9): error MSB3091: Task failed because "sgen.exe" was not found, or the .NET Framework SDK v2.0 is not installed. The task is looking for "sgen.exe" in the "bin" subdirectory beneath the location specified in the SDKInstallRootv2.0 value of the registry key HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\.NETFramework. You may be able to solve the problem by doing one of the following: 1.) Install the .NET Framework SDK v2.0. 2.) Manually set the above registry key to the correct location. 3.) Pass the correct location into the "ToolPath" parameter of the task. [exec] Done Building Project "C:\Projects\Production\Tools\ReportInstaller\ReportInstaller.csproj" (default targets) -- FAILED. [exec] Done Building Project "C:\Projects\Production\Tools\ReportInstaller\ReportInstaller.sln" (default targets) -- FAILED. [exec] [exec] Build FAILED. [exec] [exec] "C:\Projects\Production\Tools\ReportInstaller\ReportInstaller.sln" (default target) (1) -> [exec] "C:\Projects\Production\Tools\ReportInstaller\ReportInstaller.csproj" (default target) (2) -> [exec] (GenerateSerializationAssemblies target) -> [exec] C:\Windows\Microsoft.NET\Framework\v2.0.50727\Microsoft.Common.targets(1902,9): error MSB3091: Task failed because "sgen.exe" was not found, or the .NET Framework SDK v2.0 is not installed. The task is looking for "sgen.exe" in the "bin" subdirectory beneath the location specified in the SDKInstallRootv2.0 value of the registry key HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\.NETFramework. You may be able to solve the problem by doing one of the following: 1.) Install the .NET Framework SDK v2.0. 2.) Manually set the above registry key to the correct location. 3.) Pass the correct location into the "ToolPath" parameter of the task. [exec] [exec] 0 Warning(s) [exec] 1 Error(s) [exec] [exec] Time Elapsed 00:00:00.24 [call] C:\Projects\Production\Source\reports.build(15,4): [call] External Program Failed: C:\Windows\Microsoft.NET\Framework\v3.5\MSBuild.exe (return code was 1) What am I doing wrong here that is causing MSBuild to STILL be unable to find SGen?

  Read the article

• How to send mails through php script?

  - by Zeeshan Rang

  Hello everyone. How can i send mails through the php script?? I am trying to do somthing like this: for($k=0;$k<=$x->length-1;$k++) { for($l=0;$l<=$j-1;$l++) { if($y->item($k)->nodeValue==$JobNoArr[$l] && $AcceptanceDateArr[$l]=='0000-00-00') { //echo $v->item($k)->nodeValue ; $email = $v->item($k)->nodeValue . ","; $to = $email; $subject = "My subject"; $txt = "Hello world!"; $headers = "From: [email protected]" . "\r\n" . "CC: [email protected]"; mail($to,$subject,$txt,$headers); } } } Please help me in this issue. Best Zeeshan

  Read the article

< Previous Page | 93 94 95 96 97 98 99 100 101 102 103 104  | Next Page >