Search Results

Search found 7288 results on 292 pages for 'streaming media'.

Page 97/292 | < Previous Page | 93 94 95 96 97 98 99 100 101 102 103 104  | Next Page >

• How to install Windows 7 From Network?

  - by George

  Hello SuperUser My question is that is it possible to install Windows 7 (Current RTM Version) on a computer without using removable media like DVD or USB. First thing that comes to my mind is network but i dont have experience of doing Fresh Install of Windows 7 via Network. How to install Windows 7 via network without any removable media? P.S. I know some may think that doing so, is just a waste of time and it's easier to do it with removable media, but in current situation the target PC neather has CD/DVD Drive nor supports booting from USB. And in addition to that, Target computer is connected to Network via Wireless Network (Dunno if it will make any problem with installation).

  Read the article

• Do you have any additions or alterations to this list of popular audio formats?

  - by roja

  All, I am trying to compile a list of common audio file formats used in both personal storage and peer transmission. I have compiled the following list, do you think that there are any significant formats missing? Are any of them not actually common formats? Any advice/alterations are highly useful. advanced audio coding, apple lossless audio file, atrac3 audio file, atrac audio file, audio interchange file format, core audio file, free lossless audio codec file, mpeg 1 audio layer 3, mpeg 2 audio, mpeg 4 audio book file, musical instrument digital interface, ogg vorbis compressed audio file, open media framework file, real audio, real audio media, waveform audio file format, windows media audio Kind regards, Roja

  Read the article

• What causes "All-in-one USB Card Reader" to create 6 drives that always appear in Disk Management?

  - by tim11g

  I installed a "All-in-one USB Card Reader" to read SD cards and other media. It has caused six new drives to appear in Disk Management with six new drive letter assignments. These drives and letters are always present, even when there are no cards in the reader. When unused, they are labeled "No Media". Why does this multifunction reader cause these phantom Disks to appear and consume drive letters? Every USB port can (and does) allow removable media to be mounted and assigned a drive letter, and the drive letter assignment "disappears" when the USB drive is removed. Why are these card reader's drives and letters staying allocated permanently? Is there anything that can be done to make the slots work like a typical USB drive? (The reader is in fact connected to USB).

  Read the article

• How do I concatenate a lot of files into one inside Hadoop, with no mapping or reduction

  - by Leonard

  I'm trying to combine multiple files in multiple input directories into a single file, for various odd reasons I won't go into. My initial try was to write a 'nul' mapper and reducer that just copied input to output, but that failed. My latest try is: vcm_hadoop lester jar /vcm/home/apps/hadoop/contrib/streaming/hadoop-*-streaming.jar -input /cruncher/201004/08/17/00 -output /lcuffcat9 -mapper /bin/cat -reducer NONE but I end up with multiple output files anyway. Anybody know how I can coax everything into a single output file?

  Read the article

• Video Recording on iPhone

  - by gn-mithun

  I have this iPhone app, which plays streaming video from a source(Just video, no audio). Is there any mechanism by which i can capture this streaming video or record them, for later playback?

  Read the article

• Can't install Parallels Tools on Debian 7.2.0

  - by jfm429

  (Parallels Desktop 9, latest version) As per instructions, I switch to root: $ su - root $ whoami root $ echo $EUID 0 and then execute the installer: $ cd /media/cdrom0 $ ./install and I get this error: sudo: unable to execute ./install: Permission denied What? I'm root! What's with this? I double check to make sure the execute bit is set: $ ls -lA | grep install$ -r-xr-xr-x 1 root root 17284 Oct 25 09:22 install Yep. People online are saying that you need to drag the install script to the terminal after typing sudo. So I do that, and this command is what's formed: $ sudo '/media/cdrom0/install' sudo: unable to execute /media/cdrom0/install: Permission denied What's the solution here?

  Read the article

• Sharing an external hard drive in Ubuntu using Samba

  - by cambraca

  /media/MYDISK is where my hard drive is mounted automatically. I created a symlink using: ln -s /media/MYDISK /home/camilo/MYDISK chmod 777 /home/camilo/MYDISK I'm setting up smb.conf like this: [myshare1] comment = external disk browsable = yes path = /home/camilo/MYDISK guest ok = yes read only = no create mask = 0775 Also, in the [global] section I tried adding the following lines: follow symlinks = yes wide links = yes unix extensions = no The problem is that when browsing the shared folder in Windows 7, I get a "\\etc\myshare1 is not accessible" error. When pointing the path to a regular folder it works fine. Also, when I point it directly to /media/MYDISK, it shows the same error. EDIT: to make it more interesting, I have no graphical interface, so I need to touch the config files directly..

  Read the article

• Sharing an external hard drive in Ubuntu using Samba

  - by cambraca

  /media/MYDISK is where my hard drive is mounted automatically. I created a symlink using: ln -s /media/MYDISK /home/camilo/MYDISK chmod 777 /home/camilo/MYDISK I'm setting up smb.conf like this: [myshare1] comment = external disk browsable = yes path = /home/camilo/MYDISK guest ok = yes read only = no create mask = 0775 Also, in the [global] section I tried adding the following lines: follow symlinks = yes wide links = yes unix extensions = no The problem is that when browsing the shared folder in Windows 7, I get a "\\etc\myshare1 is not accessible" error. When pointing the path to a regular folder it works fine. Also, when I point it directly to /media/MYDISK, it shows the same error. EDIT: to make it more interesting, I have no graphical interface, so I need to touch the config files directly..

  Read the article

• S.M.A.R.T - Predictive Failure Count

  - by Bastien974

  I'm monitoring my IBM ServeRAID M5015 controller for RAID status with MegaCLI, I have this on one of the disk : Enclosure Device ID: 252 Slot Number: 6 Enclosure position: 0 Device Id: 14 Sequence Number: 2 Media Error Count: 32 Other Error Count: 0 Predictive Failure Count: 18 Last Predictive Failure Event Seq Number: 8119 PD Type: SAS Raw Size: 279.396 GB [0x22ecb25c Sectors] Non Coerced Size: 278.896 GB [0x22dcb25c Sectors] Coerced Size: 278.464 GB [0x22cee000 Sectors] Firmware state: Online, Spun Up SAS Address(0): 0x5000c50042c319c9 SAS Address(1): 0x0 Connected Port Number: 5(path0) Inquiry Data: IBM-ESXSST9300653SS B6336XN04HC10525B633 IBM FRU/CRU: 81Y9671 FDE Capable: Not Capable FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: 6.0Gb/s Link Speed: 6.0Gb/s Media Type: Hard Disk Device Drive: Not Certified Drive Temperature :33 Celsius What does this mean exactly ? I can't find an exact description, is there a way to have more details ? The RAID array has the Optimal state. Media Error Count: 32 Predictive Failure Count: 18 Is there a way through the CLI to power-on the front LED so I physically know which disk I need to replace ?

  Read the article

• problem in exporting a partition on a usb stick as nfs volume

  - by Bond

  I have a USB disk which has 2 partitions.I exported one of them (on NFS) and now I am trying to mount it at client machine. Each time it gets error mount -t nfs 192.168.1.19:/media/vol2 /mnt/nfs/ mount.nfs: access denied by server while mounting 192.168.1.19:/media/vol2 Here is the /etc/exports file entry showmount -e on nfs server gives Export list for bond: /media/vol2 */24 On the client machine nfs-client package is installed. What more I need to check? Is it logged some where?

  Read the article

• Nginx proxy to s3 bucket gets 400 Invalid Argument

  - by elssar

  I have a Django app in which I serve media files through an nginx proxy to s3. The relevant python code response = HttpResponse() response['X-Accel-Redirect'] = '/s3_redirect/%s' % filefield.url.replace('http://', '') response['Content-Disposition'] = 'attachment; filename=%s' % filefield.name return response The nginx block for the internal redirect is location ~* ^/s3_redirect/(.*) { internal; set $full_url http://$1; proxy_pass $full_url; And the request logged by s3 is. REST.GET.OBJECT <media file> "GET <media file>" 400 InvalidArgument 354 - 4 - "http://<referer>" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_3) AppleWebKit/537.1 (KHTML, like Gecko) Chrome/21.0.1180.89 Safari/537.1" - I, for the life of me, can't figure out what's wrong. The url send to nginx by the app is valid, it works in the browser. And nginx is sending a request to s3.

  Read the article

• How to execute programs on mounted partition

  - by DevNoob

  This is the aplication I want to run. -rwxr-xr-x 1 manuel manuel 582841 Nov 22 09:51 PromServerMain This is the fstab entry /dev/sda8 /media/data0 ext4 defaults,user 0 2 This is the mountpoint lrwxrwxrwx 1 manuel manuel 5 Nov 16 14:23 data -> data0 drwxrwxr-x 9 manuel manuel 4096 Nov 22 09:26 data0 This is what I get manuel@P5KC /media/data/Projekte/PromServer/src $ ./PromServerMain bash: ./PromServerMain: Keine Berechtigung manuel@P5KC /media/data/Projekte/PromServer/src $ sudo ./PromServerMain sudo: unable to execute ./PromServerMain: Permission denied Even as root. I have no clue whats wrong. Any suggestions? System is Debian Wheezy Xfce.

  Read the article

• Cannot get Backup Exec to backup Exchange.

  - by Shawn Gradwell

  I have a media server, Windows Server 2008 SP2 running Backup Exec 2010 R2. The SQL and other Windows agents work but I cannot backup the Exchange 2010 server running Windows Server2008 R2. I have the correct license for the Exchange agent - installed on the media server, and I installed Exchange Management tools on the media server. The 'Microsoft Exchange Database Availability Group' option is greyed out and if I select the server under a new backup job I can expand the 'Microsoft Information Store' option and see the mail database name but showing 0Kb. When I try to back it up it gives an error displaying: The job failed with the following error: Backup Exec attempted to back up an Exchange database according to the job settings. The database was not found, however. Update the selection list and run the job again.

  Read the article

• Crossover LAN connection between Ubuntu And Windows 7 is not working

  - by brett

  my question is closely related to: How do I connect Ubuntu 10.04 and Windows 7 with an Ethernet cable? What I am after is: Windows 7-------wireless-----\ Wifi router Ubuntu 10.04----wireless-----/ Windows 7-------wireless-----\ | cross_over_cable Wifi router | Ubuntu 10.04----wireless-----/ What I did was On Windows edit system32\drivers\etc\hosts Add the following line: 192.168.253.2 my_ubuntu_computer_name_&-wired //?not sure if this is right On Ubuntu: sudo gedit /etc/hosts Add the following line: 192.168.253.1 my_pc_computer_name&-wired //?not sure if this is right and then Ubuntu 12.04 as the host Right click on the Network Manager applet, click Edit Connections... In the Wired tab, click Auto eth0, then click Edit... In the IPv4 Settings tab, change Method: to Shared to other computers. Click Apply and enter your password when it asks you. Close everything and reboot. Plug the Ethernet cable into both computers. But, I can connect to my windows network folders from ubuntu via wifi I can't connect to my ubuntu network folders from windows via wifi(in fact this bit was working before - so my wifi connection is worse) my ubuntu Auto Ethernet seems to be on From Ubuntu eth0 Link encap:Ethernet HWaddr 00:11:2f:f3:43:8d inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:2fff:fef3:438d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:172 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:27279 (27.2 KB) Interrupt:19 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1147 errors:0 dropped:0 overruns:0 frame:0 TX packets:1147 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94380 (94.3 KB) TX bytes:94380 (94.3 KB) wlan0 Link encap:Ethernet HWaddr 00:03:c9:e9:6f:bf inet addr:10.1.1.7 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::203:c9ff:fee9:6fbf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13186 errors:0 dropped:0 overruns:0 frame:0 TX packets:12187 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1598882 (1.5 MB) TX bytes:1189555 (1.1 MB) From Windows: Windows IP Configuration Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : BoB Link-local IPv6 Address . . . . . : fe80::ecf7:c445:3725:b9c1%12 IPv4 Address. . . . . . . . . . . : 10.1.1.4 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.1.1.1 Tunnel adapter Local Area Connection* 15: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:1423:3ae3:f5fe:fefb Link-local IPv6 Address . . . . . : fe80::1423:3ae3:f5fe:fefb%23 Default Gateway . . . . . . . . . : :: Tunnel adapter isatap.BoB: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : BoB Tunnel adapter isatap.{D0C8EBA1-335D-4620-8570-6C36E8786D72}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . :

  Read the article

• RHEL kickstart with external DVDrom drive

  - by AndyM

  HI I've an old Dell poweredge server with an CDROM drive. I've attached a USB DVDROM and USB stick with my ks.cfg on so I can install RHEL from DVD not loads of CDs :-) I can boot from the RHEL media in DVDROM and point the installer to the USB ks.cfg. This works but the ks.cfg script has the cdrom keyword in it. The install then stops and asks for the RHEL media to be in the CDROM drive not the DVDROM. How can I change the ks.cfg so it uses the external DVDROM for the install media not servers builtin cdrom drive ? I know I can go and rebuild my DVD image to include the ks.cfg , but this is an extra step I dont want to do if I have to. Regards Andy

  Read the article

• UUID in Mountain Lion

  - by Naji

  I am trying to find my external HDD UUID in Mountain Lion but diskutil info /dev/disk1s1 returns: Najis-MacBook-Air:~ ****$ diskutil info disk1s1 Device Identifier: disk1s1 Device Node: /dev/disk1s1 Part of Whole: disk1 Device / Media Name: Untitled 1 Volume Name: My Book Escaped with Unicode: My%FF%FE%20%00Book Mounted: Yes Mount Point: /Volumes/My Book Escaped with Unicode: /Volumes/My%FF%FE%20%00Book File System Personality: NTFS Type (Bundle): ntfs Name (User Visible): Windows NT File System (NTFS) Partition Type: Windows_NTFS OS Can Be Installed: No Media Type: Generic Protocol: USB SMART Status: Not Supported Total Size: 2.0 TB (2000364240896 Bytes) (exactly 3906961408 512-Byte-Blocks) Volume Free Space: 212.5 GB (212506509312 Bytes) (exactly 415051776 512-Byte-Blocks) Device Block Size: 512 Bytes Read-Only Media: No Read-Only Volume: Yes Ejectable: Yes Whole: No Internal: No And there is no UUID. What is wrong exactly? Thank you.

  Read the article

• A "region code" restriction for a custom created video dvd file

  - by user180820

  I want to create a video dvd ( no menus, just "plug and play" ) from a few video files. I`m doing it like this: ffmpeg -i sample-media/hellboy-2.wmv -y -target ntsc-dvd sample-media-to-mpeg/hellboy-2.vob dvdauthor -o sample-dvd -x dvdauthor-settings.xml mkisofs -dvd-video -o hellboy-2-trailers.iso sample-dvd/ where "dvdauthor-settings.xml" is: link. But when I try to play the iso file in windows it says: Windows Media Player cannot play the DVD because the disc prohibits playback in your region of the world. You must obtain a disc that is intended for your geographic region. When I open the *.IFO file with IfoEdit it says that all world regions are unabled. Can someone tell me why is this happening? ( maybe the whole process of creating the *.iso file is wrong? )

  Read the article

• Is there anything that can be done to make X forwarding over LAN less painful?

  - by Earlz

  I have two *nix machines that I like to remotely do graphical things sometimes with. One of those machines is my Arch Linux media server, and another is my OpenBSD router/general server. My current task was installing a Windows XP over virtual box on my media server. I preferred to do the installation from my main workstation so that I could continue to watch TV from my media server on it's "actual" display. I soon noticed that X forwarding is quite painful though, even over low-latency LAN connections. Are there any settings I can tweak to make it a bit less painfully slow, jittery, and laggy? My LAN is rather small, 100Mbit, and ping times to the other box average at about 0.15ms. Also, I know Virtualbox has a VNC mode it can use instead of doing X forwarding, but this particular task was just an example

  Read the article

• Can a switch consume bandwidth?

  - by aashiq

  I have a network with a router and a switch. At first my ISP's optical fiber is connected with media converter input port. Than Ethernet cable (output port of Media converter) is connected with the switch. Then an output Ethernet cable is connected with our inner Microtik router. Then this router is connected with another LAN switch. From this switch we have got every connection other switch. It is our total network structure. Our bandwidth is 2 Mbps. From the 11th of March our MRTG graph shows high all the time even when my all switch is switched off except LAN switch. That's why our line is breaking up (Voice call). How could be it possible? My all PC's bandwidth is limited but when connected PC with media converter directly then the graph shows normal. That's why I can't blame my ISP.

  Read the article

• Is it Secure to Grant Apache User Ownership of Directories & Files for Wordpress

  - by Oudin

  I'm currently setting up WordPress on an Ubuntu server 12 everything runs fine but there is an issue when it comes to automatically updating and uploading media via WP as Apache "www-data" user does not have permissions to write to the directories. "user1" has full permission All my directories have permissions of 0755 and files 644 my directories setup is as follows: /home/user1/public_html All WP files and directories are in "public_html" In order to work around the auto updating and uploading media I've granted Apache user ownership to the following directories sudo chown www-data:www-data wp-content -R sudo chown www-data:www-data wp-includes -R sudo chown www-data:www-data wp-admin -R I would like to know security wise how secure this is and if it is not secure what would be the best solution? That will allow me to keep all files and directories owned by user1 and still allow wp to be able to automatically update and uploading media

  Read the article

• Easier way to create floppy disk images?

  - by Bryan

  I'm using Vyatta routers with KVM and want to attach a floppy drive with a config file for Vyatta when I boot the image. I'll be doing this over and over again, and as such am looking for an automated way of creating the floppy images. Right now, I'm doing the following: Create floppy image with qemu-img create Format floppy image with mkdosfs Mount floppy image with mount -t fat /tmp/floppy.img /media/floppy Populate floppy image with cp -r /tmp/configs/ /media/floppy/ Unmount floppy image with umount /media/floppy Save floppy image with mv /tmp/floppy.img ~/floppies/ Any chance there's an easier way to do this?! Perhaps a shortcut application that I can give a directory to and it will do all this for me w/out having to mount the image?

  Read the article

• RewriteRule applying pattern even though 1 of the RewriteCond's failed

  - by BHare

  #www. domain . tld RewriteCond %{HTTP_HOST} (?:.*\.)?([^.]+)\.(?:[^.]+)$ RewriteCond /home/%1/ -d RewriteRule ^(.+) %{HTTP_HOST}$1 RewriteRule (?:.*\.)?([^.]+)\.(?:[^.]+)/media/(.*)$ /home/$1/client/media/$2 [L] RewriteRule (?:.*\.)?([^.]+)\.(?:[^.]+)/(.*)$ /home/$1/www/$2 [L] Here is rewritelog output: #(4) RewriteCond: input='tfnoo.mydomain.org' pattern='(?:.*\.)?([^.]+)\.(?:[^.]+)$' [NC] => matched #(4) RewriteCond: input='/home/mydomain/' pattern='-d' => not-matched #(3) applying pattern '(?:.*\.)?([^.]+)\.(?:[^.]+)/media/(.*)$' to uri 'http://www.mydomain.org/files/images/logo.png' #(3) applying pattern '(?:.*\.)?([^.]+)\.(?:[^.]+)/(.*)$' to uri 'http://www.mydomain.org/files/images/logo.png' #(2) rewrite 'http://www.mydomain.org/files/images/logo.png' -> '/home/mydomain/www/logo.png' If you note on the 2nd 4 it failed the -d (if directory exists) pattern. Which is correct. mydomain does not have a /home/. Therefore it should never rewrite, atleast according to my understanding that all rewriterules are subject to rewriteconds as logical ANDs.

  Read the article

• backing up ntfs disk using rsync on ubuntu

  - by user70366

  For a long time I was using windows. I have a separate drive I use to keep copies of my media files, photos etc. on, which I periodically backup to an external drive. In Windows I used SyncToy to do this. After my Windows stopped booting, I decided to switch to Linux (Ubuntu 10.10). That seems to be going fine, but now I want to backup my drive to the external drive like before. Mostly the two drives will be already the same with maybe about 10GB of extra files added. So I try to use rsync to synchronise the two drives like this: rsync --dry-run -rvlt --modify-window=1 /media/Antonio1TB/Backup /media/FREECOM\ HDD/Backup The problem is the dry run indicates that every file on the drive will be copied. Not just the files I have recently added. What is the correct command to synch two NTFS drives under Ubuntu so that files that already exist don't get copied again? Thanks.

  Read the article

• How can I share data from a Samsung Wave Mobile phone with the Mac OS?

  - by M. Bedi

  This is driving me up the wall just a bit. I have a new Samsung Wave mobile phone. It is running the Bada OS. The mobile phone does not come with anyone software for the Mac. The Kies desktop interface is only available for Windows. I did try installing the Kies software in a VM with Parallels 5 but it did not detect the phone connected via USB. I tried using Bluetooth file exchange on the Mac; it lets me browse the file system on the Wave phone but not actually see any of the media files; I just get empty directory views. But I am able to access files using media sharing with the Wave phone and my PS3. So what would be a Mac desks top app that can be used a media sharing browser?

  Read the article

• Using Shell32 to extract Mimes on Windows Server 2008

  - by Léon Pelletier

  In a desktop app, I'm using Shell32 to extract Mime infos and ID3 tags. I want to do the same in ASP.Net on server side with http posted files, plus fetch some other infos, but as a Windows Server 2008, there are not several media applications installed, so I wonder if it will still retrieve a lot of informations from the files. Will it be possible to do it from server side? If yes, will it fetch several Mimes without media app installed. If not, is there some Mime pack to get some file informations without the app being installed. [EDIT] I installed VLC player and Windows Media Player on the server, which provide all MP3s / movies infos (Duration, Artist, Album, Width, Height, etc.), but I don't know if this is a good practice.

  Read the article

< Previous Page | 93 94 95 96 97 98 99 100 101 102 103 104  | Next Page >