Search Results

Search found 4453 results on 179 pages for 'kernel parametes'.

Page 158/179 | < Previous Page | 154 155 156 157 158 159 160 161 162 163 164 165  | Next Page >

• Debian, 2 NICs load-balancing or agregating with one same gateway

  - by pouney

  Hi, I have one server, with double NICs connected to one switch with the same gateway. Behind the switch we have internet. |Debian| - eth0 - switch - internet - eth1 - same I don't understand how to load-balancing between eth0 and eth1. The inbound/outbound traffic always use eth1. This is the config: # The primary network interface allow-hotplug eth0 auto eth0 iface eth0 inet static address 192.168.248.82 netmask 255.255.255.240 network 192.168.248.80 broadcast 192.168.248.95 gateway 192.168.248.81 allow-hotplug eth1 auto eth1 iface eth1 inet static address 192.168.248.83 netmask 255.255.255.240 network 192.168.248.80 broadcast 192.168.248.95 gateway 192.168.248.81 Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.248.80 0.0.0.0 255.255.255.240 U 0 0 0 eth1 192.168.248.80 0.0.0.0 255.255.255.240 U 0 0 0 eth0 0.0.0.0 192.168.248.81 0.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.248.81 0.0.0.0 UG 0 0 0 eth0 Ips aren't real, it's just for the example. Anybody have an idea on correct routing to use eth0 on 192.168.248.82 and eth1 on 192.168.248.83 ? I have many example for multiple gateway but here it's the same. Thanks all. Regards

  Read the article

• datawind ubislate 9ci tablet computer hanging on boot

  - by user57924

  I am new to this forum. I purchased a new tablet Datawind Ubislate 9ci. It is a 9 inch no-bluetooth tablet. Details: Android 4.1.1 Rock chip RK2928 KERNEL linux version 3.0.36 I was trying to install CWM through mobile odin and ROM manager but my tablet was not supported so i downloaded build.prop editor from google play and changed it to some other cwm recognizable model viz. Samsung, nexus etc. When i was doing the above mentioned procedure, suddenly my tablet is coming up to bootloading and hanging there only and not opening i went to recovery and tried to do wipe data factory reset but failed to get opened after boot android system recovery(3e) has the following options 1)reboot system now 2)apply update from ADB 3)apply update from external storage 4)update rkimage from external storage 6)wipe data factory reset 7)wipe cache partition 8)recovery system from back up i tried to do wipe data factory reset 2-3 times but still hanging at boot i had not made any back up before this bootloop and also tried hard reset by pressing needle at the back please somebody help me to get rid of this problem and also tell me how to unlock bootloader thank you

  Read the article

• Understanding RedHats recommended tuned profiles

  - by espenfjo

  We are going to roll out tuned (and numad) on ~1000 servers, the majority of them being VMware servers either on NetApp or 3Par storage. According to RedHats documentation we should choose the virtual-guestprofile. What it is doing can be seen here: tuned.conf We are changing the IO scheduler to NOOP as both VMware and the NetApp/3Par should do sufficient scheduling for us. However, after investigating a bit I am not sure why they are increasing vm.dirty_ratio and kernel.sched_min_granularity_ns. As far as I have understood increasing increasing vm.dirty_ratio to 40% will mean that for a server with 20GB ram, 8GB can be dirty at any given time unless vm.dirty_writeback_centisecsis hit first. And while flushing these 8GB all IO for the application will be blocked until the dirty pages are freed. Increasing the dirty_ratio would probably mean higher write performance at peaks as we now have a larger cache, but then again when the cache fills IO will be blocked for a considerably longer time (Several seconds). The other is why they are increasing the sched_min_granularity_ns. If I understand it correctly increasing this value will decrease the number of time slices per epoch(sched_latency_ns) meaning that running tasks will get more time to finish their work. I can understand this being a very good thing for applications with very few threads, but for eg. apache or other processes with a lot of threads would this not be counter-productive?

  Read the article

• nfs mount with nfs 3

  - by rahrahruby

  I am running CentOS 6.4 Kernel version 2.6.32-358.23.2.el6.x86_64 #1 SMP and have the following nfs info: nfs-utils-lib-1.1.5-6.el6.x86_64 nfs4-acl-tools-0.3.3-6.el6.x86_64 nfs-utils-1.2.3-36.el6.x86_64 and am trying to mount an nfs volume with nfs3. I have the following line in my fstab: 172.16.11.87:/volume1/web /home/nas nfsver=3 rsize=8192,wsize=8192,timeo=14,intr(no_root_squach) When I run nfsstat it still shows the client as nfs4 Server rpc stats: calls badcalls badauth badclnt xdrcall 0 0 0 0 0 Client rpc stats: calls retrans authrefrsh 1988817 6 1988818 Client nfs v4: null read write commit open open_conf 0 0% 36943 1% 21606 1% 401 0% 392369 19% 375986 18% open_noat open_dgrd close setattr fsinfo renew 0 0% 0 0% 387945 19% 22904 1% 3 0% 2914 0% setclntid confirm lock lockt locku access 1 0% 1 0% 0 0% 0 0% 0 0% 97856 4% getattr lookup lookup_root remove rename link 613996 30% 29888 1% 1 0% 1248 0% 253 0% 414 0% symlink create pathconf statfs readlink readdir 26 0% 226 0% 2 0% 3 0% 0 0% 3825 0% server_caps delegreturn getacl setacl fs_locations rel_lkowner 5 0% 0 0% 0 0% 0 0% 0 0% 0 0% exchange_id create_ses destroy_ses sequence get_lease_t reclaim_comp 0 0% 0 0% 0 0% 0 0% 0 0% 0 0% layoutget layoutcommit layoutreturn getdevlist getdevinfo ds_write 0 0% 0 0% 0 0% 0 0% 0 0% 0 0% ds_commit 0 0%

  Read the article

• debian 6 losing a large amount of packets

  - by Sc0rian

  I have a rather strange problem. We covered all the obvious hardware related issues (different nic, eth cable and switch) however I cannot seem to stop eth dropping packets. I have 4 servers all exactly the same. driver: e1000e version: 1.2.20-k2 firmware-version: 1.8-0 bus-info: 0000:06:00.0 They are all running the latest kernel(2.6.32-5-amd64). However they do this: RX packets:17073870634 errors:0 dropped:14147208 overruns:0 frame:0 another server: eth0 Link encap:Ethernet HWaddr e0:69:95:05:2f:cb inet addr:10.10.10.86 Bcast:10.10.10.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5455209277 errors:0 dropped:375445 overruns:0 frame:0 TX packets:3666134366 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6688414486673 (6.0 TiB) TX bytes:1611812171539 (1.4 TiB) Interrupt:20 Memory:d0600000-d0620000 eth1 Link encap:Ethernet HWaddr 00:1b:21:b7:7a:ce inet addr:10.10.0.86 Bcast:10.10.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15473695728 errors:0 dropped:5808325 overruns:0 frame:0 TX packets:20112364421 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9192378766434 (8.3 TiB) TX bytes:20216368266761 (18.3 TiB) Interrupt:17 Memory:d0280000-d02a0000 A massive amount of dropped packets. I have tried to load on the latest driver, 1.9.5. This did nothing. I'm not sure what else to do.

  Read the article

• windows 7 turns off itself everyday at about 9am

  - by Radek

  I was given this comp at work and after a week or so this strange thing started to happen in the middle of doing something :-( It turns off itself at about 9.10am every morning Just once a day and it works fine after it had it little nap. it happens both if the comp was on all night or I turned it off before leaving the office. I tried to swapped the memory as I was told that there was an issue with memory. But moving or removing any memory did not make any difference. I am not aware that I would install any program that could cause that. I installed AVG and set it up to do every day scan about 8am + if restart is needed it requires user confirmation. 'The Software Protection service has stopped' few minutes before it turned off itself but it happened also at other times without the computer turned off. I turned off Windows automatic updates as the first thing when I got the comp configuration Windows 7 Ultimate Intel Core2 Quad Q9550 at 2.8GH, 8GB RAM ST31000528AS Barracuda 7200.12 SATA 3Gb/s 1TB Update Below message are logged when I turn the comp on again. Message 1: The previous system shutdown at 9:08:54 AM on ?6/?29/?2010 was unexpected. Message 2: Level:Critical Source: Kernel Power EventID 41 Task Category (63) The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. Log after manual restart Update 2 (task scheduler)

  Read the article

• How to avoid sshfs freezing?

  - by Andreas Hagen

  So the issue is this: I've installed sshfs on Ubuntu 12.04 and I'm trying to connect to a couple of remote servers. So initially the mount seams successful. Sometimes Gnome even picks it up and displays the "new device found" box at the bottom of the screen. but from here on there is not much that works. Or at least not any more. The first couple of times i connected it seamed to work fine, and I was able to transfer some files, then i disconnected using fusermount -u <folder> and after reconnecting a little later the trouble started. Now after executing sshfs -o ServerAliveInterval=15 -o reconnect -C -o workaround=all -o idmap=user root@<host>:/ <folder>, when I change directory into the mount-point, the shell just freezes. Strangely ls -al <folder> works when listing just the root of the remote system, but nothing more. Also every file-explorer I've tried freezes just like cd <folder>. To me it seamed like there was some kind of zombie thread or something hanging around my system, due to the fact that it did work the first time, so I have tried rebooting but no luck. sshfs -V gives this: SSHFS version 2.3 FUSE library version: 2.8.6 fusermount version: 2.8.6 using FUSE kernel interface version 7.12 So yea, any ideas?

  Read the article

• How to determine the root cause of a system lockup on Ubuntu 8.04 LTS?

  - by jdt141

  I'm currently working a project that involves setting up a PC/104 stack and running Ubuntu 8.04 LTS. We need to use the PC/104 stack because its an embedded application - and we're required to use a DeviceNet peripheral card to communicate to other devices. (DeviceNet is just a protocol on top of CAN.) Anyway, the following hardware is on the stack: Kontron MOPSPM104 with a 1GHz Intel Celeron processor ConnectTech FlashDrive/104 4GB Industrial Temp (-40 to +85 C) Woodhead (Molex) PC104DVNIO DeviceNet card A run of the mill 104 power supply The Kontron Board offers two serial ports, one VGA out, and two USB ports. The DeviceNet card is an ISA card. Because of this (per the User's Guide for the Kontron Board), I have manually set the IRQs in the BIOS to be appropriately configured, and turned off ACPI in both the BIOS and passed the appropriate flag in GRUB. I've installed Ubuntu 8.04 desktop, 32 bit. The problem that I'm having is that, from time to time, the entire 104 stack locks up. This only seems to happen in two cases, both of which we're running GNOME. We have a custom application that uses the DeviceNet card, and the system will lock up, or (more frequently) when we're running Firefox and either surfing for some information or trying to test it - typically by streaming video from a IP-camera. The reason I ask this questions is I cannot determine the root cause of this lockup. The IRQs appear to correctly configured in the BIOS and as the Kernel sees them, and nothing is logged to dmesg. If you all could help me determine the root cause of this lockup, I would greatly appreciate it. Thanks.

  Read the article

• openvpn problem

  - by Jared Voronik

  I have a problem with openvpn. I have already setup openvpn sucessfully on some other servers in the past (basic configuration, nothing special). On this server, I used the same config file, but for setting up nat iptables -t nat -A POSTROUTING -s 10.4.0.0/24 -o eth0 -j MASQUERADE doesn't work. It gives error: iptables v1.3.5: can't initialize iptables table `nat': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. How do I fix this error? Also, if I can't fix this error, can I do bridging instead of routing? I have only 1 interface, and I can connect to remote server only via ssh (and need to avoid reboots if at all possible) so if briding means a whole ethernet card has to be devoted to the openvpn (and no other servers) then briding is out, otherwise I can use briding. Do you know of a simple, step by step guide to configure openvpn briding (just simple openvpn server and clients that can access internet through vpn server, nothing fancy)?

  Read the article

• Route all wlan0 traffic over tun0

  - by Tuinslak

  I'm looking for a way to route all wlan0 traffic (tcp and udp) over tun0 (openvpn). However, all other traffic originating from the device itself should not be routed through tun0. I'm guessing this could be realized using iptables or route, but none of my options seem to work. # route add -net 0.0.0.0 gw 172.27.0.1 dev wlan0 SIOCADDRT: No such process Info: This is because the VPN server is not redundant, and wlan users are not really important. However, all services running on the device are fairly important and having a VPN virtual machine with no SLA on it is just a bad idea. Trying to minimize the odds of something going wrong. So setting the VPN server as default gateway is not really an option. I also want all wlan0 user to use the VPN server's IP address as external IP. Edit with the script provided: root@ft-genesi-xxx ~ # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 172.27.0.17 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.13.37.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0 172.27.0.0 172.27.0.17 255.255.192.0 UG 0 0 0 tun0 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 root@ft-genesi-xxx ~ # ./test.sh RTNETLINK answers: No such process root@ft-genesi-xxx ~ # cat test.sh #!/bin/sh IP=/sbin/ip # replace with the range of your wlan network, or use fwmark instead ${IP} rule add from 10.13.37.0/24 table from-wlan ${IP} route add default dev tun0 via 127.72.0.1 table from-wlan ${IP} route add 10.13.37.0/24 dev wlan0 table from-wlan

  Read the article

• 100% CPU load on Ubuntu 10.04.3 LTS 64bit

  - by deadtired

  I have 2 days since I am trying to fix this issue, with no success. The server is a mysql database server. Hardware: DELL Poweredge 1950, 2x Intel Xeon Quad Core E5345 @ 2.33GHz, 16 Gb mem, 2x 146Gb SAS (software RAID1) Software: Ubuntu 10.04.3 LTS, MySQL 5.1.41 Issue: while mysql is not used and runs with no database, everything seems alright. As soon as I install a database, it has the reason to bring all 8 cores in 100% with low memory consumption. So, you can imagine the load average goes high (I saw 212 load average for the first time). The server doesn't become unresponsive, but you can see it's slow while browsing the project installed. Additional info: the database used is not more than 24MB and it was moved from a server with less resources and a lot more larger databases. So it's not the database/project. my.cnf is not a reason also, as I used both default one and the one I use on the same distribution on another server.What is interesting is that mysql doesn't close any process and runs to the limit of the max_connections. Logs are quiet. Nothing there. I switched to this Ubuntu version after I suspected some problems in the newly Ubuntu 11.10 server. This one worked alright for an hour after I made a kernel upgrade to 3.0.1 (it was using the memory also) I tested disk speed and seems alright. Some more output on the running server: dstat -cndymlp -N total -D total 3: htop command: Idea? Did anyone meet the same problem? Any fix you can think of?

  Read the article

• CentOS 6.3 Virtual under OpenVZ cannot ping, host lookups, outbound connections while postfix running

  - by Paul Cravey

  My best theory is that some kernel limit is being hit preventing outbound connections. We have tried basically everything from tcpdumps to provisioning an entirely new virtual server (we do not have this problem on any other virtuals), however the problem somehow carried over, even with new postfix build (working). Emails work, and outbound connections work, so long as postfix does not have too much going on. /proc/user_beancounters shows no limits being hit (show below). Nevertheless, pings fail even to IP addresses. TCP stack appears healthy. Load is low. No iowait. Flushed iptables already. Has anyone experienced anything like this? uid resource held maxheld barrier limit failcnt 3: kmemsize 166216365 170262528 9223372036854775807 9223372036854775807 0 lockedpages 0 0 9223372036854775807 9223372036854775807 0 privvmpages 285727 351885 9223372036854775807 9223372036854775807 0 shmpages 16933 17605 9223372036854775807 9223372036854775807 0 dummy 0 0 0 0 0 numproc 150 303 9223372036854775807 9223372036854775807 0 physpages 314156 326191 0 1280000 0 vmguarpages 0 0 9223372036854775807 9223372036854775807 0 oomguarpages 165355 165355 9223372036854775807 9223372036854775807 0 numtcpsock 89 172 9223372036854775807 9223372036854775807 0 numflock 22 76 9223372036854775807 9223372036854775807 0 numpty 1 2 9223372036854775807 9223372036854775807 0 numsiginfo 0 75 9223372036854775807 9223372036854775807 0 tcpsndbuf 2733472 4371752 9223372036854775807 9223372036854775807 0 tcprcvbuf 1798336 5427296 9223372036854775807 9223372036854775807 0 othersockbuf 491120 1000760 9223372036854775807 9223372036854775807 0 dgramrcvbuf 0 238728 9223372036854775807 9223372036854775807 0 numothersock 361 505 9223372036854775807 9223372036854775807 0 dcachesize 135941831 136114679 9223372036854775807 9223372036854775807 0 numfile 2905 4990 9223372036854775807 9223372036854775807 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 numiptent 8 9 9223372036854775807 9223372036854775807 0 [root@bni /]# ping 4.2.2.1 PING 4.2.2.1 (4.2.2.1) 56(84) bytes of data. --- 4.2.2.1 ping statistics --- 9 packets transmitted, 0 received, 100% packet loss, time 8493ms [root@bni /]# service postfix stop [root@bni /]# ping 4.2.2.1 PING 4.2.2.1 (4.2.2.1) 56(84) bytes of data. 64 bytes from 4.2.2.1: icmp_seq=1 ttl=53 time=8.63 ms 64 bytes from 4.2.2.1: icmp_seq=2 ttl=53 time=8.62 ms 64 bytes from 4.2.2.1: icmp_seq=3 ttl=53 time=8.63 ms 64 bytes from 4.2.2.1: icmp_seq=4 ttl=53 time=8.66 ms Outbound connections of all sorts fail when postfix is running.

  Read the article

• Two DHCP interfaces asigned to two default gateways to OS

  - by user140600

  I have a Ubuntu box that has two networking interfaces (eth0 and wlan0). They are both configured for DHCP in /etc/network/interfaces, but they both assign a default gateway: /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto wlan0 iface wlan0 inet dhcp wireless-essid test Result of route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 172.16.1.1 0.0.0.0 UG 100 0 0 wlan0 0.0.0.0 10.0.0.1 0.0.0.0 UG 100 0 0 eth0 10.0.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 172.16.1.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0 How can I set up /etc/network/interfaces to have only one default gateway, on the interface I want? Worst case scenario, how can I at least control which one gets on top on the route -n command, each boot? Note: This box will travel a lot, and will be connected to different networks, so I don´t know in advance the IP addresses/ranges it will have. Sometimes the default gw interface will be eth0. Sometimes it will be wlan0 ... So, this needs to be kind of automatic ...

  Read the article

• How to configure a large mtu (linux)

  - by Somejan

  I have a gigabit ethernet connection from my laptop to my router, and a working ipv6 connection to the internet. I can receive very large packets from sites on the internet, with sizes up to at least 10000 bytes (according to wireshark). (edit: turns out to be linux's 'generic receive offload') However, when trying to send anything, my local computer fragments at just below 1500 bytes for ipv6. (On ipv4, I can send tcp packets to the internet of at least 1514 bytes, I can ping with packets up to the configured mtu of 6128 but they are blackholed.) I'm on ubuntu 12.04. I have configured an mtu for my eth0 of 6128 (the maximum it accepts), both using ip link set dev eth0 mtu 6128 and in the NetworkManager applet gui, and restarted the connection. ip link show eth0 shows the 6128 mtu is indeed set. ip -6 route shows that none of the paths the kernel knows about have an mtu set. I can ping over ipv4 with packets up to 6128 bytes (though I don't get responses), but when I do ping6 myrouter -c3 -s1500 -Mdo I get error replies from my own computer saying that the packets are too large and the mtu is 1480. I have confirmed with Wireshark that nothing is put on the wire, and the replies are indeed generated by my own computer. So, how do I get my computer to use the larger mtu?

  Read the article

• linux container bridge filters ARP reply

  - by Dani Camps

  I am using kernel 3.0, and I have configured a linux container that is bridged to a tap interface in my host computer. This is the bridge configuration: :~$ brctl show bridge-1 bridge name bridge id STP enabled interfaces bridge-1 8000.9249c78a510b no ns3-mesh-tap-1 vethjUErij My problem is that this bridge is dropping ARP replies that come from the ns3-mesh-tap-1 interface. Instead, if I statically populate the ARP tables and ping directly everything works, so it has to be something related to ARP. I have read about similar problems in related posts, and I have tried with the solutions explained therein but nothing seems to work. Specifically: ~$ grep net.bridge /etc/sysctl.conf net.bridge.bridge-nf-call-arptables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-filter-vlan-tagged = 0 net.bridge.bridge-nf-filter-pppoe-tagged = 0 arptables and ebtables are not installed. iptables FORWARD is all set to accept: Chain FORWARD (policy ACCEPT) target prot opt source destination The bridged interfaces are set to PROMISC: ~$ ifconfig ns3-mesh-tap-1 Link encap:Ethernet HWaddr 1a:c7:24:ef:36:1a ... UP BROADCAST PROMISC MULTICAST MTU:1500 Metric:1 vethjUErij Link encap:Ethernet HWaddr aa:b0:d1:3b:9a:0a .... UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 The macs learned by the bridge are correct (checked with brctl showmacs). Any insight on what I am doing wrong would be greatly appreciated. Best Regards Daniel

  Read the article

• VMWare web UI intermittent access on CentOS

  - by PeteWilliams

  Hiya, I've got a CentOS 5.2 server that I'm trying to get set up as a development environment. As part of this, I planned to install VMWare Server 2 and set up several virtual development servers. I've got as far as installing VMWare Server 2 but access to the remote control panel is only working intermittently. If I access it through Firefox at https://127.0.0.1:8333/ui/# it usually says either: "Connection intterupted: connection was reset before the page loaded" Or "Firefox can't establish a connection to the server at 127.0.0.1" But every now and then it lets me in and I'll manage a few clicks in the web UI before it kicks me out with the following error: "The server could not complete a request (HTTP 0 ). The server encountered an unexpected condition that prevented it from fulfilling the request. If this problem persists, please contact your system administrator." I've done all the updates available in CentOS except one OpenOffice one that is causing a conflict, and I re-ran wmware-config.pl after updating the kernel. Though I went with all the defaults as I don't really know what I'm doing! I've since rebooted and nothing changed. I've also tried accessing the control panel remotely from another machine in the network and the results are the same. Does anyone have any ideas what might be causing this and how I can resolve it? I'm afraid I'm a developer playing at sys-admin, so I may be missing something obvious! Many thanks Pete Update I have now reinstalled both the operating system and VMWare and I'm still getting the same issue. I wonder if it's a result of the settings I'm putting in on the config.pl script..?

  Read the article

• Windows recovery partition with GRUB2

  - by Actorclavilis

  So I recently got a new Toshiba laptop and installed Ubuntu 12.04 on it. Since it is a "Windows 7 Enabled" machine or some other proprietary nonsense like that, a few hardware features are designed only to work with W7. Eventually I found a way to enable these hardware functions by booting into the W7 recovery disc; however, they sporadically stop working. I'm moderately surprised that I was able to get anything to work at all, so I don't especially want to spend more time fixing the problems in a different fashion. Now I don't actually own the recovery disc; it's my father's. Since it's a pain to have to go asking for the disc every time the features stop working, I made an image of the disc and was hoping to make a 'recovery' partition like some computers have. However, unetbootin and GRUB2 both want a kernel and initrd to point to on startup, and something like set root=(hd0,1) loopback lo /w7r.iso set root=(lo) chainloader +1 in the spirit of the makeactive/ chainloader +1 commands that I used to use to dual-boot Linux and Windows simply gives me a file-not-found error. My question, therefore, is: Is it possible to, having written a Windows iso to a partition (such as with dd if=w7r.iso of=/dev/sda4) to a partition, convince GRUB2 to boot from it? Thanks in advance.

  Read the article

• Lion MacBook Pro will not load webpages with DNS just after wake

  - by NReilingh

  I'm working with a 2011 MacBook Pro running Lion (10.7.2), that after waking from sleep (i.e. opening the lid) takes an inordinately long amount of time (2-3 minutes or more) to get a usable internet connection. Upon waking, the wi-fi icon signifies it is negotiating a network connection, and completes one a few seconds later. At this point, network diagnostics will not show any issues, and everything in Network preferences looks as normal: I'm connected to the proper network, have the right IP address and gateway, and DNS settings are correct. However, any site accessed with a domain name (like http://www.google.com) in Safari will return the "You are not connected to the Internet." error. Accessing a site directly, say, with Google's 74.125.226.212, is successful. Yet, Network Diagnostics will insist that DNS is functioning properly. After a few minutes, the following lines will be printed to the Console log, and regular behavior will be restored. 11/18/11 8:11:31.288 PM airportd: _doAutoJoin: Already associated to “Wireless”. Bailing on auto-join. 11/18/11 8:11:32.000 PM kernel: en1: BSSID changed to 00:25:9c:63:91:bd This behavior occurs only when waking from sleep--not when turning wi-fi on and off. This problem also occurs when using a wired Ethernet connection. As per this thread, I have tried flushing the DNS cache and wiping the wireless network from memory (it's not a protected network). Neither have worked.

  Read the article

• Looking for way to log process terminations on OS X (Mac)

  - by Stan Sieler

  I'm looking for a way to log all process terminations on my Mac (OS X 10.6.8). (And see pid, timestamp, process name) I've implemented something similar for HP-UX, but it required a kernel-level driver and intercepting several variations of "exit()" (the normal one, and the one invoked on behalf of a process while it's aborting). Why do I want the info? I've been seeing messages in my system log file (dmesg) like: CODE SIGNING: cs_invalid_page(0x1000): p=91550[GoogleSoftwareUp] clearing CS_VALID CODE SIGNING: cs_invalid_page(0x1000): p=92088[GoogleSoftwareUp] clearing CS_VALID Although dmesg lacks timestamps, apps/Utilities/Console : Database : all : search for CS_VALID shows that the messages appears about once every 58 1/2 minutes. I suspect the number after "p=" is a process id (pid) ... but for a process that has long since terminated by the time I see the message. So, if there was a process termination log mechanism that recorded the pid, the time of termination, the reason for termination, and the process name (at time of termination), that would probably allow me to determine who's causing those errors to be logged! (No, I'm not running Chrome on my Mac, and "ps -ef | grep -i goog" gets no hits either ... I'm not consciously running any Google apps on the Mac) thanks, Stan [email protected]

  Read the article

• Spotlight has stopped indexing/returning anything in /Applications

  - by pra

  After a recent kernel panic & restart, Spotlight no longer seems to know anything about the files under my /Applications folder. I used to launch Safari.app, Opera.app, Textedit.app, etc via Spotlight as a matter of routine. Now, I get "No results found" for all of them (except Textedit.app, which launches a demo text editor from a Qt installation). The programs are still there & still launch directly from Finder. I've already run disk utility & verified the disk, no issues. I repaired disk permissions, which made several changes, but to no effect. Is there anything else I can do, short of re-installing MacOS? Update: I already verified that "Applications" was still checked in my Spotlight preferences. It was still returning applications located elsewhere (the Qt textedit sample app), so that shouldn't have been the issue. A few hours later it resolved itself; I guess there's a background process running on some interval.

  Read the article

• Random and Selective ARP blindness in VMWare ESXi 4.1

  - by Peter Grace

  We have multiple VMWare ESX servers spread out amongst our company, doing various tasks. One particular ESXi host is exhibiting very peculiar behavior. We detect it when our monitoring system (Orion) notifies us that it can no longer ping the box. Upon jumping on the local console of the guest in question, we see that it cannot ping any new addresses that aren't already in its ARP table. At first we thought that the problem was just related to one of our guests, as the problem seemed to always happen to another guest, DevRedis. However, this afternoon the problem swapped and started happening on ApacheBox rather than DevRedis. When I have been fortunate to catch the problem, I have run tcpdump on both sides of the connection (one side being vmware, the other side being a physical webserver) and have noticed the following course of events: Guest ApacheBox sends an ARP request for the physical address of server WindowsBeast WindowsBeast tenders an ARP is-at back to the network indicating its physical mac address. ApacheBox never sees the ARP is-at response. The ESX host in question is running VMware ESXi, 4.1.0, 348481 The two guests (DevRedis and ApacheBox) are both running CentOS 6.3, however they are running two separate kernel versions ( 2.6.32-279.9.1.el6.x86_64 and 2.6.32-279.el6.x86_64 ) so I'm not entirely sure it's a CentOS problem. Does anyone have any thoughts on what might cause this? Has anyone run into it before?

  Read the article

• Linux Live CD only works when Windows is in Legacy mode?

  - by Vee

  I have asked a similar question before and no one was able to help me but I think it was because I wasn't phrasing it properly. This is a better restatement of the question. I have Windows 8 and Linux Mint dual booted on my pc. When I tried to boot the Linux from a CD ROM only, it would give me the following error: error: failure reading sector 0x0 from 'hd1' error: you need to load the kernel first. Press any key to continue... The Linux Mint works fine but otherwise, but it gives this error when I try to boot from CD. The boot Linux from CD only worked when I changed the Windows to Legacy mode in the BIOS settings. When I changed it back to UEFI, it would give the same error. Why is this? How can I fix it? I am somewhat new so is there anything else I should know about all of this? NOTE: I changed the Linux into UEFI mode using boot-repair but that still did not solve the problem when I tried to boot from CD ROM.

  Read the article

• aufs user permissions

  - by user56395

  Anyone know why this doesn't work? Is this user error, AUFS feature or bug maybe: rac@tecraS1:~/tmp$ mkdir orig tmp au rac@tecraS1:~/tmp$ sudo mount -t tmpfs none tmp rac@tecraS1:~/tmp$ sudo chown -R rac tmp rac@tecraS1:~/tmp$ echo hello > orig/hello rac@tecraS1:~/tmp$ sudo mount -t aufs -o br=tmp:orig none au rac@tecraS1:~/tmp$ ls -al au total 8 drwxrwxrwt 4 rac root 100 2011-01-06 13:53 . drwxr-xr-x 5 rac rac 4096 2011-01-06 13:52 .. -rw-r--r-- 1 rac rac 6 2011-01-06 13:53 hello rac@tecraS1:~/tmp$ rm au/hello rm: cannot remove `au/hello': Operation not permitted rac@tecraS1:~/tmp$ Seems the aufs files were created as root and user has no access to them: rac@tecraS1:~/tmp$ sudo rm au/hello rac@tecraS1:~/tmp$ ls -al tmp total 4 drwxrwxrwt 4 rac root 120 2011-01-06 13:53 . drwxr-xr-x 5 rac rac 4096 2011-01-06 13:52 .. -r--r--r-- 2 root root 0 2011-01-06 13:53 .wh.hello -r--r--r-- 2 root root 0 2011-01-06 13:53 .wh..wh.aufs drwx------ 2 root root 40 2011-01-06 13:53 .wh..wh.orph drwx------ 2 root root 40 2011-01-06 13:53 .wh..wh.plnk rac@tecraS1:~/tmp$ OS is the latest Lucid with 2.6.35-23 stock kernel. No idea about aufs version. Using sudo chown -R rac tmp/.wh* fixes the problem. Thanks for looking.

  Read the article

• VMWare web UI intermittent access on CentOS

  - by PeteWilliams

  I've got a CentOS 5.2 server that I'm trying to get set up as a development environment. As part of this, I planned to install VMWare Server 2 and set up several virtual development servers. I've got as far as installing VMWare Server 2 but access to the remote control panel is only working intermittently. If I access it through Firefox at https://127.0.0.1:8333/ui/# it usually says either: "Connection intterupted: connection was reset before the page loaded" Or "Firefox can't establish a connection to the server at 127.0.0.1" But every now and then it lets me in and I'll manage a few clicks in the web UI before it kicks me out with the following error: "The server could not complete a request (HTTP 0 ). The server encountered an unexpected condition that prevented it from fulfilling the request. If this problem persists, please contact your system administrator." I've done all the updates available in CentOS except one OpenOffice one that is causing a conflict, and I re-ran wmware-config.pl after updating the kernel. Though I went with all the defaults as I don't really know what I'm doing! I've since rebooted and nothing changed. I've also tried accessing the control panel remotely from another machine in the network and the results are the same. Does anyone have any ideas what might be causing this and how I can resolve it? I'm afraid I'm a developer playing at sys-admin, so I may be missing something obvious! Many thanks Pete Update I have now reinstalled both the operating system and VMWare and I'm still getting the same issue. I wonder if it's a result of the settings I'm putting in on the config.pl script..?

  Read the article

• Disable or remove filter driver for single HID device

  - by snoopen

  Running Windows XP in a corporate setting here. I have an issue where a filter driver is interfering with the functionality of different USB HIDs. For example graphics tablets do not respond while the filter driver is in place. I've also had the issue with foot pedals used with transcription software. My question is really two fold: A) what makes Windows use a filter driver on one HID but not another? B) when a filter driver is causing conflicts how can I disable it on the affected devices? Background I've previously narrowed down the issue to the filter driver by uninstalling the software (Funk Proxy Host) responsible for the filter driver. The software is a type of RDP we use here at work. (I might have even booted into safe mode and renamed the file, I forget). I believe the filter driver is present to disable or modify the use of the local keyboard and mouse while admin staff are assisting users. Either way I don't have the authority to just go uninstalling this software. As far as I can tell the software versions are the same, however I'm not sure if the device driver definitions are all the same as I don't know where these things would be located. To check for the presence of the filter driver I locate the hardware device in Device Manager, click Properties Driver tab Driver Details.... It shows up as ph32ihid.sys. Even though all machines are meant to have the same SOE and do have Funk Proxy Host installed I don't always have issues with the same HIDs. A few machines here the foot pedals without any issues. I've not had any machines work with the graphics tablet without uninstalling Funk software. Driver details I've just read up a bit more about filter drivers and found the drivers description in the registry under "HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\ProxyHostHIDFilter" There it's called "Kernel-mode HID filter driver for the Proxy Host". Presumably I could also disable it here but that would be system wide which is probably not desirable?

  Read the article

< Previous Page | 154 155 156 157 158 159 160 161 162 163 164 165  | Next Page >