Search Results

Search found 7940 results on 318 pages for 'intel wireless'.

Page 20/318 | < Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >

  • Broadcom device 4365 wireless driver for 12.04

    - by NilPointer
    My laptop (Dell Inspiron 17R 5720) came with preinstalled Ubuntu 11.10. I removed it and installed 12.04. Now I can't find driver for wireless. Apparently, in 11.10 there was Broadcom-STA driver. But in 12.04 there is no additional drivers to install. I tried using: sudo m-a a-i broadcom-sta But building fails on 26%. How can I install driver According to lspci i got: Broadcom Corporation Device 4365 (rev 01)

    Read the article

  • Ubuntu, No wireless networks found after correctly installed madwifi

    - by Peter
    Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

    Read the article

  • Intel Extreme Tuning utility options are greyed

    - by Abhishek Sha
    I'm having a ASUS K55VM with Intel Core i7 3610QM (IvyBridge) with a NVIDIA GT630M. I'm trying to operate the Intel XTU, but as you can see in the screenshot, all the options are greyed out. Can you please help with this situation. Another are is the CPU Throttling (Intel SpeedStep) which is always shown as 0%. But in the Intel Turbo Monitor, the Speed keeps dynamically changing. Then why is the CPU Throttling always at 0%?:

    Read the article

  • Realtek/Intel NIC transfer speed

    - by thepurplepixel
    I have just purchased a Gigabyte GA-X58A-UD7 motherboard, and it has dual Realtek RTL8111D gigabit LAN ports. I also have an Intel PRO/1000 MT PCI gigabit network card lying around from an old desktop. I've heard that Intel PCI-E network cards will often outperform Realtek, Marvell, or other non-Intel on-board network adapters, but my question is will the PRO/1000 MT PCI card outperform a single Realtek RTL8111D gigabit network adapter in terms of transfer speed, or should I keep what I have/buy a PCI-E Intel network adapter?

    Read the article

  • Installing Intel Iris Drivers on Parallels 9

    - by Eren Yildirim
    I'm running windows 8.1 on Parallels 9 on Mac OS X 10.9.3 Mavericks. Before that I used to have VMWare and I could manage to install Intel Iris drivers for OpenCL SDK. But Parallels installs tools for virtualization I guess and in device manager I see Parallels Display Adapter (VDDM) instead of Intel Iris Graphics Processor. How can I see the device and be able to install latest Intel drivers so that I can Install Intel OpenCL SDK. Thank you.

    Read the article

  • 32-bit Ubuntu or 64-bit w/Intel Atom D510 w/4GB RAM?

    - by T.J. Crowder
    (I've seen this question and some related ones, and perhaps this is a duplicate although part of my question is specific to the Atom D510.) I'm going to be installing Ubuntu on a new silent desktop as my latest (and hopefully last) attempt to switch from Windows to Linux for at least most everyday tasks. The new machine is entirely passvely cooled, but as a consequence, not astonishingly powerful — an Atom D510 (dual-core, 1.6GHz, HT) on Intel's D510MO board. That's fine, I won't use it for gaming, (much) video editing, etc. It's a 64-bit processor and I'm maxing the board out at 4GB of RAM (hey, that 1.6 CPU needs all the help it can get), which naturally raises the question of whether to install Ubuntu 64-bit or 32-bit (and if the latter, either live with the missing RAM, or do the PAE kernel dance). Although I've used Linux on servers for years, I'm very nearly a Linux desktop newbie and am not currently in the mood to fight driver wars and such. So if I'm setting myself up for failure with 64-bit, I'll live with the missing ~0.8GB or fiddle with PAE. But if 64-bit is entirely "ready," great, I'm there. So: Do most mainstream apps (now) play nicely with 64-bit Linux? I can't help but notice the "AMD" in the ISO image filename ubuntu-10.04-desktop-amd64.iso and I know AMD lead the way on this stuff — does Ubuntu 64-bit play nicely with Intel processors? Just generally, would you recommend one or the other? (And if anyone has any experience with Ubuntu specifically on the D510 [32-bit or 64-bit] which might lead me one way or t'other, that would be useful.) Thanks in advance.

    Read the article

  • Cannot find wireless driver for HP laptop

    - by rodey
    I have an HP laptop (model: dv7-1267cl, Windows 7 64-bit Home Premium) and I cannot find the wireless driver for the laptop. I am need of a different version because my wireless connection under Windows is flaky and unreliable. I have problems printing to my wireless printer and logging in to and using several sites like reddit.com, phoenix.edu and facebook.com - I get several "page cannot be displayed" messages while using my wireless connection. I disable my wireless adapter and use an ethernet cable and it all works fine. I also used an Ubuntu Live CD to confirm that there is not a problem with the hardware. This is software/driver issue. The drivers were auto installed by the OS. The Device Manager shows the wireless adapter as Atheros AR5009 802.11 a/g/n WiFi Adapter. I have checked the HP website for my laptop and they do not have wireless drivers listed for that model wireless adapter. I have also checked with atheros.com and I do not see my model adapter on their list of available hardware. Device Manager lists the Hardware ID's for my adapter as: PCI\VEN_168C&DEV_002A&SUBSYS_1381103C&REV_01 PCI\VEN_168C&DEV_002A&SUBSYS_1381103C PCI\VEN_168C&DEV_002A&CC_028000 PCI\VEN_168C&DEV_002A&CC_0280 A search for the first Hardware ID turned up this question from experts-exchange.com. tl;dr A driver does not exist for that model adapter.

    Read the article

  • how to get adobe flash fullscreen video fluid with an atom processor?

    - by Antoine Rodriguez
    My system has an atom N270 + intel i915 graphic card. Under Windows I can enjoy 720p bigbuckbunny youtube video fullscreen without any trouble. Under Ubuntu 12.04 I have laggy and choppy fullscreen video and choppy video when not fullscreen. I've seen that under ubuntu the cpu is almost always at 100% use. What I must do in order to have videos playing well under ubuntu ? I've already tried the following : Force flash gpu detection : (no result) : mkdir /etc/adobe echo "OverrideGPUValidation = 1" | sudo tee -a /etc/adobe/mms.cfg grub options (had results but not enough) : i915_enable_rc6=1 i915_enable_fbc=1 i915_lvds_downclock=1 pcie_aspm=force updated intel drivers (glasen ppa) Using chrome instead of firefox (had impact but not enough)

    Read the article

  • Wireless is detected, but not connecting. Ethernet works. How to correct the wireless address?

    - by Lucas
    I am running Ubuntu 14.04 with cable internet, and my wireless is detected and connected, but I cannot connect to the internet. I know the problem is with my machine because other machines are connecting to the same router just fine. I can connect via ethernet just fine as well. Here are some notable tests: ping 192.168.0.105 works with 0% packet loss, but ping 192.168.0.1 has 100% packet loss. When I plug in my ethernet, ping 192.168.0.1 works with 0% packet loss. My wireless name is tg, and the router ip is 192.168.0.1 (where I can enter username and password). I suspect that I need to change my wireless address from 192.168.0.105 to 192.168.0.1. Any suggestions on how to proceed? extra info: [lucas@lucas-ThinkPad-W520]/home/lucas$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"tg" Mode:Managed Frequency:2.462 GHz Access Point: 00:02:6F:83:F8:F4 Bit Rate=1 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:52 Invalid misc:166 Missed beacon:0 [lucas@lucas-ThinkPad-W520]/home/lucas$ ifconfig eth0 Link encap:Ethernet HWaddr f0:de:f1:b2:53:53 inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f2de:f1ff:feb2:5353/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:980003 errors:0 dropped:0 overruns:0 frame:0 TX packets:498384 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1320506168 (1.3 GB) TX bytes:59780591 (59.7 MB) Interrupt:20 Memory:f3a00000-f3a20000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:21927 errors:0 dropped:0 overruns:0 frame:0 TX packets:21927 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1781719 (1.7 MB) TX bytes:1781719 (1.7 MB) wlan0 Link encap:Ethernet HWaddr 24:77:03:29:8f:dc inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::2677:3ff:fe29:8fdc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11828 errors:0 dropped:0 overruns:0 frame:0 TX packets:15444 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4855662 (4.8 MB) TX bytes:2250585 (2.2 MB) [lucas@lucas-ThinkPad-W520]/home/lucas$ lspci -nn | grep 0280 03:00.0 Network controller [0280]: Intel Corporation Centrino Ultimate-N 6300 [8086:4238] (rev 3e) [lucas@lucas-ThinkPad-W520]/home/lucas$ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no with ethernet unplugged: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 wlan0 with ethernet plugged in: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 [lucas@lucas-ThinkPad-W520]/home/lucas$ nm-tool NetworkManager Tool State: connected (global) - Device: wlan0 [tg] ---------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: no HW Address: 24:77:03:29:8F:DC Capabilities: Speed: 52 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) tatum: Infra, 40:8B:07:D8:A5:04, Freq 2437 MHz, Rate 54 Mb/s, Strength 42 W PA WPA2 ums: Infra, 00:20:A6:72:52:BF, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 Alpha 40: Infra, 28:CF:E9:86:59:5D, Freq 5260 MHz, Rate 54 Mb/s, Strength 30 W PA WPA2 thepromiselan: Infra, 58:6D:8F:51:E5:54, Freq 2452 MHz, Rate 54 Mb/s, Strength 34 $ PA WPA2 xfinitywifi: Infra, 06:1D:D5:84:27:A0, Freq 2437 MHz, Rate 54 Mb/s, Strength 52 *tg: Infra, 00:02:6F:83:F8:F4, Freq 2462 MHz, Rate 54 Mb/s, Strength 73 W PA2 ums: Infra, 00:20:A6:A1:9F:25, Freq 2452 MHz, Rate 54 Mb/s, Strength 44 BRIAN-PC_Network:Infra, 20:AA:4B:DD:93:D6, Freq 2462 MHz, Rate 54 Mb/s, Strength 35 W PA2 HOME-C0F8: Infra, 44:32:C8:D2:C0:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 40 W PA WPA2 abcsexy: Infra, 28:28:5D:27:5D:85, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 W PA WPA2 IPv4 Settings: Address: 192.168.0.105 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: e1000e State: connected Default: yes HW Address: F0:DE:F1:B2:53:53 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.0.100 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1

    Read the article

  • Unity 3D not Working on Acer D270 w/ Intel GMA 3600

    - by amol.kamath
    I recently bought myself an Acer Aspire One D270 with the GMA 3600 graphics chipset thinking I would get some lovely graphics. However, I am stuck using Unity 2D and I cant figure out how to enable 3D. None of the fixes I have found so far have worked. Another effect of this is that I cant change the backlight brightness. So whenever I open the lid, looking at the screen is like staring into the sun. Is there a driver for it in the works? Does the 3.4 kernel support the chipset and most of all is there a way to fix this? Please help

    Read the article

  • Ubuntu 12.04 wireless (wifi) not working, can not upgrade to 12.10, touchpad gestures not working. What to do?

    - by Ritwik
    I installed ubuntu 12.04 LTS 3 days ago and since then wireless feature and touchpad gestures are not working. Tried everything on internet but still unsuccessful. I cant upgrade to ubuntu 12.10. These are the following comments I tried. Please help me. EDIT: just realized usb 3.0 is also not working. COMMAND lsb_release -r OUTPUT ----------------------------------------------------------------- Release: 12.04 ----------------------------------------------------------------- COMMAND lspci OUTPUT ------------------------------------------------------------------ 00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller (rev 06) 00:01.1 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x8 Controller (rev 06) 00:02.0 VGA compatible controller: Intel Corporation 4th Gen Core Processor Integrated Graphics Controller (rev 06) 00:03.0 Audio device: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller (rev 06) 00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 05) 00:16.0 Communication controller: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 (rev d5) 00:1c.1 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #2 (rev d5) 00:1c.2 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #3 (rev d5) 00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM86 Express LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05) 00:1f.3 SMBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller (rev 05) 07:00.0 3D controller: NVIDIA Corporation GF117M [GeForce 610M/710M / GT 620M/625M/630M/720M] (rev a1) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 07) 09:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5229 PCI Express Card Reader (rev 01) 0f:00.0 Network controller: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter (rev 01) ------------------------------------------------------------------ COMMAND sudo apt-get install linux-backports-modules-wireless-lucid-generic OUTPUT ------------------------------------------------------------------- Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package linux-backports-modules-wireless-lucid-generic ------------------------------------------------------------------- COMMAND cat /etc/lsb-release; uname -a OUTPUT ------------------------------------------------------------------- DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.5 LTS" Linux ritwik-PC 3.2.0-67-generic #101-Ubuntu SMP Tue Jul 15 17:46:11 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux ------------------------------------------------------------------- COMMAND lspci -nnk | grep -iA2 net OUTPUT ------------------------------------------------------------------- 08:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 07) Subsystem: Hewlett-Packard Company Device [103c:225d] Kernel driver in use: r8169 -- 0f:00.0 Network controller [0280]: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter [168c:0036] (rev 01) Subsystem: Hewlett-Packard Company Device [103c:217f] ------------------------------------------------------------------- COMMAND lsusb OUTPUT ------------------------------------------------------------------- Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:8008 Intel Corp. Bus 002 Device 002: ID 8087:8000 Intel Corp. ------------------------------------------------------------------- COMMAND iwconfig OUTPUT ------------------------------------------------------------------- lo no wireless extensions. eth0 no wireless extensions. ------------------------------------------------------------------- COMMAND rfkill list all OUTPUT ------------------------------------------------------------------- 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: hp-bluetooth: Bluetooth Soft blocked: no Hard blocked: no ------------------------------------------------------------------- COMMAND lsmod OUTPUT ------------------------------------------------------------------- Module Size Used by snd_hda_codec_realtek 224215 1 bnep 18281 2 rfcomm 47604 0 bluetooth 180113 10 bnep,rfcomm parport_pc 32866 0 ppdev 17113 0 nls_iso8859_1 12713 1 nls_cp437 16991 1 vfat 17585 1 fat 61512 1 vfat snd_hda_intel 33719 3 snd_hda_codec 127706 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 17764 1 snd_hda_codec snd_pcm 97275 2 snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61929 2 snd_seq_midi,snd_seq_midi_event nouveau 775039 0 joydev 17693 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq ttm 76949 1 nouveau uvcvideo 72627 0 snd 79041 15 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device videodev 98259 1 uvcvideo drm_kms_helper 46978 1 nouveau psmouse 98051 0 drm 241971 3 nouveau,ttm,drm_kms_helper i2c_algo_bit 13423 1 nouveau soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm v4l2_compat_ioctl32 17128 1 videodev hp_wmi 18092 0 serio_raw 13211 0 sparse_keymap 13890 1 hp_wmi mxm_wmi 13021 1 nouveau video 19651 1 nouveau wmi 19256 2 hp_wmi,mxm_wmi mac_hid 13253 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62190 0 ------------------------------------------------------------------- COMMAND sudo su modprobe -v ath9k OUTPUT ------------------------------------------------------------------- insmod /lib/modules/3.2.0-67-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_hw.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_common.ko insmod /lib/modules/3.2.0-67-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k.ko ------------------------------------------------------------------- COMMAND do-release-upgrade OUTPUT ------------------------------------------------------------------- Err Upgrade tool signature 404 Not Found [IP: 91.189.88.149 80] Err Upgrade tool 404 Not Found [IP: 91.189.88.149 80] Fetched 0 B in 0s (0 B/s) WARNING:root:file 'quantal.tar.gz.gpg' missing Failed to fetch Fetching the upgrade failed. There may be a network problem. ------------------------------------------------------------------- COMMAND sudo modprobe ath9k dmesg | grep ath9k NO OUTPUT FOR THEM COMMAND dmesg | grep -e ath -e 80211 OUTPUT ------------------------------------------------------------------- [ 13.232372] type=1400 audit(1408867538.399:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=975 comm="apparmor_parser" [ 13.232615] type=1400 audit(1408867538.399:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=975 comm="apparmor_parser" [ 15.186599] ath3k: probe of 3-4:1.0 failed with error -110 [ 15.186635] usbcore: registered new interface driver ath3k [ 88.219329] cfg80211: Calling CRDA to update world regulatory domain [ 88.351665] cfg80211: World regulatory domain updated: [ 88.351667] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 88.351670] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 88.351671] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 88.351673] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 88.351674] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 88.351675] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) ------------------------------------------------------------------- COMMAND sudo apt-get install touchpad-indicator OUTPUT ------------------------------------------------------------------- Reading package lists... Done Building dependency tree Reading state information... Done The following extra packages will be installed: gir1.2-gconf-2.0 python-pyudev Suggested packages: python-qt4 python-pyside.qtcore The following NEW packages will be installed: gir1.2-gconf-2.0 python-pyudev touchpad-indicator 0 upgraded, 3 newly installed, 0 to remove and 0 not upgraded. Need to get 84.1 kB of archives. After this operation, 1,136 kB of additional disk space will be used. Do you want to continue [Y/n]? Y Get:1 http://ppa.launchpad.net/atareao/atareao/ubuntu/ precise/main touchpad-indicator all 0.9.3.12-1ubuntu1 [46.5 kB] Get:2 http://archive.ubuntu.com/ubuntu/ precise/main gir1.2-gconf-2.0 amd64 3.2.5-0ubuntu2 [7,098 B] Get:3 http://archive.ubuntu.com/ubuntu/ precise/main python-pyudev all 0.13-1 [30.5 kB] Fetched 84.1 kB in 2s (31.6 kB/s) Selecting previously unselected package gir1.2-gconf-2.0. (Reading database ... 169322 files and directories currently installed.) Unpacking gir1.2-gconf-2.0 (from .../gir1.2-gconf-2.0_3.2.5-0ubuntu2_amd64.deb) ... Selecting previously unselected package python-pyudev. Unpacking python-pyudev (from .../python-pyudev_0.13-1_all.deb) ... Selecting previously unselected package touchpad-indicator. Unpacking touchpad-indicator (from .../touchpad-indicator_0.9.3.12-1ubuntu1_all.deb) ... Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for desktop-file-utils ... Processing triggers for gnome-menus ... Processing triggers for hicolor-icon-theme ... Processing triggers for software-center ... INFO:softwarecenter.db.update:no translation information in database needed Setting up gir1.2-gconf-2.0 (3.2.5-0ubuntu2) ... Setting up python-pyudev (0.13-1) ... Setting up touchpad-indicator (0.9.3.12-1ubuntu1) ... ------------------------------------------------------------------- Not able to find ( drivers/net/wireless/ath/ath9k/hw.c ) or ( drivers/net/wireless/ath/ath9k/hw.h )

    Read the article

  • Ubuntu 12.04 Hp G72 Problem Installing proprietary wireless driver

    - by user69402
    I have a fresh Ubuntu 12.04 installed on HP G72 machine. In order for my wireless to work I need the proprietary driver installed - Broadcom STA wireless driver. Trying to install it from the System Settings gives me the error: "Sorry, installation of this driver failed. Please have a look at the log file for details: /var/log/jockey.log". So far I suspect the error to be caused by the bad "bcmwl-kernel-source" installation. What i tried: 1. remove "bcmwl-kernel-source" 2. install "bcmwl-kernel-source" installation through the terminal ends with "error code (1)". I would greatly appreciate any help Here is everything that the terminal returns: Reading package lists... Done Building dependency tree Reading state information... Done The following NEW packages will be installed: bcmwl-kernel-source 0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded. Need to get 0 B/1,151 kB of archives. After this operation, 3,514 kB of additional disk space will be used. Selecting previously unselected package bcmwl-kernel-source. (Reading database ... 170331 files and directories currently installed.) Unpacking bcmwl-kernel-source (from .../bcmwl-kernel-source_5.100.82.38+bdcom-0ubuntu6.1_amd64.deb) ... Setting up bcmwl-kernel-source (5.100.82.38+bdcom-0ubuntu6.1) ... Loading new bcmwl-5.100.82.38+bdcom DKMS files... /usr/sbin/dkms: line 467: unset: POST_REMOVE$PRE_BUMLD': not a valid identifier /usr/sbin/dkms: line 467: unset:BUILD_E\CLUWIVE_ARCH': not a valid identifier /usr/sbin/dkms: line 467: unset: $': not a valid identifier /usr/sbin/dkms: line 467: unset:$': not a valid identifier /usr/sbin/dkms: line 467: unset: modules_conf_arra}': not a valid identifier /usr/sbin/dkms: line 467: unset:$': not a valid identifier /usr/sbin/dkms: line 467: unset: $': not a valid identifier /usr/sbin/dkms: line 467: unset:$': not a valid identifier /usr/sbin/dkms: line 467: unset: $': not a valid identifier /usr/sbin/dkms: line 467: unset:$': not a valid identifier /usr/sbin/dkms: line 467: unset: `$': not a valid identifier /usr/sbin/dkms: line 419: ${!POST_REMOVE$PRE_BUMLD[@]}: bad substitution /usr/sbin/dkms: line 419: ${!BUILD_E\CLUWIVE_ARCH[@]}: bad substitution /usr/sbin/dkms: line 419: ${!$[@]}: bad substitution /usr/sbin/dkms: line 419: ${!$[@]}: bad substitution /usr/sbin/dkms: line 419: ${!$[@]}: bad substitution /usr/sbin/dkms: line 419: ${!$[@]}: bad substitution /usr/sbin/dkms: line 419: ${!$[@]}: bad substitution /usr/sbin/dkms: line 419: ${!$[@]}: bad substitution /usr/sbin/dkms: line 419: ${!$[@]}: bad substitution /usr/sbin/dkms: line 419: ${!$[@]}: bad substitution malloc: ../bash/subst.c:3671: assertion botched free: start and end chunk sizes differ Aborting.../tmp/tmp.pEXTnftUfI: line 4: modules_conf_arra}[[@]}]=[[@]}]}: command not found dkms.conf: Error! No 'DEST_MODULE_LOCATION' directive specified for record #0. dkms.conf: Error! Directive 'DEST_MODULE_LOCATION' does not begin with '/kernel', '/updates', or '/extra' in record #0. dkms.conf: Error! No 'PACKAGE_VERSION' directive specified. Error! Bad conf file. File: /usr/src/bcmwl-5.100.82.38+bdcom/dkms.conf does not represent a valid dkms.conf file. dpkg: error processing bcmwl-kernel-source (--configure): subprocess installed post-installation script returned error exit status 8 Errors were encountered while processing: bcmwl-kernel-source E: Sub-process /usr/bin/dpkg returned an error code (1)

    Read the article

  • Ubuntu 11.10 to 12.04 results in loss of N network capability - how to restore?

    - by user74273
    On Ubuntu 11.10, I had zero issues with N network detection and speed. I cannot remember whether the old driver was iwlagn or iwlwifi. This was with Ubuntu repository Linux kernel 3.0.0-22. Upon upgrading to Ubuntu 12.04, iwlwifi is the available driver and while it detects N networks, upon connection, the speed is cripplingly low and DNS look-ups do not occur (impossible to browse). This is with Ubuntu repository Linux kernel 3.2.0-26. Please note that the 11n_disable flag for the iwlwifi module cannot work for me as I require N network access. Is there another solution? Perhaps, is there a way to easily patch the new kernel with the old wireless module (just copy-and-paste the iwlagn module into the new kernel source and re-compile)? Relevant hardware specs: Dell Inspiron N5110 Network Adapter: Intel® Centrino® Wireless-N 1030

    Read the article

  • Intel Graphic card problem

    - by user10406
    Hello, I am facing a problem in installing the right driver for my computer "HP dv4 2154ca" The problem that I tried to install it couple of times but the xorg.conf file is still empty no matter what So my question is why is this file empty and how could I generate it correctly for my device The problem that I think this thing is causing is that when I maximize flash to full screen it lags the video will go slower while the sound will go smooth Thanks in advance

    Read the article

  • Install Intel USB 3.0 eXtensible Host Controller Driver for Windows Server 2008 R2 x64

    - by ffrugone
    According to Intel and Dell, by board is technically a 'desktop' board and they therefore do not support Intel USB 3.0 eXtensible Host Controller drivers for Windows Server 2008 (R2 x64). I'm trying to find a workaround. I found an entry on someone who tried to tackle this, but I can't make his fix work for me. Below, I have copied both his entry, and my reply. I'm a loyal stackoverflow user, and hopefully the people here at serverfault can help me: anyforumuser Re: GA-Z77X-UD5H USB3 Drivers not installing? « Reply #6 on: July 05, 2012, 04:12:59 am » Thanks to JoeMiner , his process for the network drivers gave me the clues to figure out to get the USB3 drivers working. I have got the intel USB3 drivers working at full speed in win server 2008r2 you have to edit the following file : 1. mup.xml in change the "Windows7" to "W2K8" 2. in setup.if2 under [groups] line starting with "HSCSDRIVER " change the "IsOS( ... )" entry to "IsOS(WIN2008_R2,WIN2008_R2_MAXSP)" inf files for all copy the content of the [Intel.NTAMD64.6.1] group to the [Intel.NTAMD64.6.2] group driver folders. here i am not entirely sure which is correct so there are some double up's. in the drivers folder copy the "Win7" folder to "win2008" , "win2008_r2" and "x64" ie your drivers folder should now contain the "win2008" , "win2008_r2" and "x64" folders and they contain contents of the win7 folder (the inf files should of already been fixed) Run install , It should install properly and work now. You will have to reboot If it doesn't work remove the intel usb3 controllers from device manager and get it to "scan for hardware changes" Good luck !!! benevida Re: GA-Z77X-UD5H Intel Network Drivers not installing? « Reply #7 on: August 13, 2012, 02:21:14 pm » Thank you anyforumuser! A process for getting this driver installed was exactly what I needed. However, I've hit a snag. I believe I've followed every step exactly as written, but I'm getting an error during installation. I get the message "One or more files that are required for installation are either missing or corrupted. Setup will exit." Behind the error, the 'Setup Progress' shows the current step as "Copying File: C:\Program Files (x86)\Intel\Intel(R) USB 3.0 eXtensible Host Controller Driver\Drivers\iusb3xhc.man". I've checked the installation files, and iusb3xhc.man seems to be a viable file in all of the Windows 2008 sub-directories of the Drivers folder. Therefore I don't see how the file could be missing and I doubt that it is corrupted, (although it does NOT exist in the \Drivers\HCSwitch folder). I opened 'Setup.if2', and there are two aspects to the step of copying iusb3xhc.man that caught my eye. First, the steps immediately preceding are set to 'error=ignore'. If they hadn't completed successfully, this is the first step where we'd hear about it. Second, this is the first step where the relative path '%source%\drivers\%_os%\%_ia%\' is used. If I haven't named the Windows 2008 sub-directories correctly, I could see where things are fouling up. In any event, if someone could take a look and make suggestions I'd appreciate it. Thank you.

    Read the article

  • Proper Drivers for 10.10 Realtek RTL8176 Wireless and Synaptic V7.2 Touchpad Devices

    - by av7000
    I have a new Toshiba Satellite L645-S4059. This is an Intel i3 64 bit machine. Two problems have occurred that I would like to fix before transferring my work from my old compaq laptop. First I can't get the wireless driver to work properly. I went to the realtek driver site and couldn't find the 8176. Instead I was shuttled to the 8188 which uses a 8192 software release. I am not sure if the kernel is just missing the name. Second I have a synaptics V7.2 touchpad which is just flaky. It eventually freezes up so I am just using a USB mouse. Appreciate anybody's experience on this.

    Read the article

  • Wireless card disappeards when restart ubuntu

    - by Kristian Jones
    I used 'additional drivers' to install 'Broadcom STA wireless driver' and it returns an error. WIthin jockey.log it says the following numerous times. 2011-02-14 21:24:06,945 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted After it returns the error the network card will work temporarily until I restart the laptop. When I restart I got to go through the procedure again of trying to activate the driver, returns an error however it works temporarily. The network card is as follows on a Dell Inspiron 1545: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] Rev 01 I have been trying to solve this myself for many hours. Any help is appreciated/

    Read the article

  • Wireless device not working...supposed problem with b43 driver

    - by Francesco
    I just installed Xubuntu 11.10 onto an old Acer Aspire 3003wlmi. The wireless card is not working. I did all the passages illustrated in the troubleshooting guide but I came up with nothing. It says that driver is b43, but when I booted from the installation cd I noted down some messages saying "Error - b43/ucode " and "Error b43/phy_...something". I had Ubuntu 10.10 installed before and I remember I had similar problems but I don't remember how to solve it. If you please can help me. thanks a lot. Francesco

    Read the article

  • Broadcom wireless card disappeards on restart

    - by Kristian Jones
    I used 'additional drivers' to install 'Broadcom STA wireless driver' and it returns an error. WIthin jockey.log it says the following numerous times. 2011-02-14 21:24:06,945 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted After it returns the error the network card will work temporarily until I restart the laptop. When I restart I got to go through the procedure again of trying to activate the driver, returns an error however it works temporarily. The network card is as follows on a Dell Inspiron 1545: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] Rev 01 I have been trying to solve this myself for many hours. Any help is appreciated/

    Read the article

  • Ubuntu 12.10 64bit fresh install, wireless issue!

    - by Dave
    Just installed a fresh Ubuntu 12.10 64bit on my laptop, run the update manager, restarted and suddenly I can't use my wifi anymore. Ubuntu software center installed automatically the wifi additional driver as you can see in my screenshot. If I mark the option "Do not use the device" and apply changes, restarting Ubuntu my wifi is back and I can use it. If I run iwconfig my terminal is showing this Now if I use Ubuntu for more than 20 minutes surfing the web my wifi it keeps to be connected but I don't receive any signal from it. Any page I try to open it simply don't open (just waiting icon). If I disconnect my wifi and connect it again, same issue, it doesn't work. The only way to make it work again is to restart Ubuntu. And the same story it happens again after aprox. 20, 30 minutes. WIFI device details: 03:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Thanks, Dave

    Read the article

  • Wireless speed drops over time and doesn't get up if not reconnected

    - by Vili Lehto
    I am using Ubuntu 12.10 64bit and I have a Asus PCE-N15 wireless card(in PCI-E slot). The problem is that first when I connect to my WiFi network the speed is just fine, and actually my link speed never drops, it shows a solid 150mb/s+ link speed and good signal. But the download and upload speeds drop dramatically after couple minutes of use and I have to reconnect to fix this. Network is type IEEE 802.11bgn and uses WPA2/AES encryption. I don't have similar problems on the windows side, and the network is working fine on every other device. iwconfig shows this: wlan0 IEEE 802.11bgn ESSID:"WLAN-AP" Mode:Managed Frequency:2.412 GHz Access Point: 00:1E:AB:05:EF:31 Bit Rate=300 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr=2347 B Fragment thr:off Encryption key:off Power Management:off Link Quality=61/70 Signal level=-49 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:2 Missed beacon:0 So the question is: Is there a way to fix this? Thanks in advance.

    Read the article

  • Installing wireless drivers without internet access [closed]

    - by Lucas Jones
    Possible Duplicate: How can I install and download drivers without internet? (This is related to my other question; my approach there didn't work.) My friend has (I'm quite sure) a Broadcom wireless chipset. However, he doesn't have any wired internet access on the machine, so his only option is to boot into Windows (he is using Wubi) and download packages there. This means we can't use the Hardware Drivers dialog to install the drivers. He can't fetch the repository information, so the Broadcom driver packages aren't showing up in Synaptic. Is there any way to get Wi-Fi working?

    Read the article

  • how to find available wireless networks

    - by Quinn
    I'm using an HP Pavilion dv6000 I've looked at other answers similar to this question how ever when I look at my network symbol it doesn't say anything that the answer below says "Make sure that your wifi hardware switch is on or not. It is either F2 or F12 or near to it. Once the switch is enabled, there is a small fan-like applet on the top panel (Gnome Network Manager), fourth from the right. Click on it and if there is no tick mark on the option 'Enable Wireless', enable it. Wait till your wifi connection name appears." it how says 'Enable Networking' my wi-fi switch is on and I've tried using terminal to kill the applet as another answer suggests trying. Does anyone have any other ideas that might help? Just in case anybodies curious as to how I'm posting this I'm on my other ubuntu laptop that's running an older version.

    Read the article

< Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >