Search Results

Search found 19446 results on 778 pages for 'network printer'.

Page 290/778 | < Previous Page | 286 287 288 289 290 291 292 293 294 295 296 297  | Next Page >

  • Configure ubuntu 12.10 to share internet through second NIC with subnetwork

    - by Dan Smith
    I have an Ubuntu 12.10 box with 2 NICs. eth0 is connected to my 192.168.1.X network, which is connected to my home router and out to the internet. I want the other interface, eth1,to support 10.0.0.x and allow devices on that network to access the internet through my ubuntu box. I do not need dhcp on the 10.0.0.x network. Here's a schematic: Internet --- home router ---- ubuntu[eth0:192.168.1.x, eth1:10.0.0.x] --- [10.0.0.x device] How do I configure the ubuntu box to share the internet with devices on that subnetwork? Thanks!

    Read the article

  • Attempting to caue packet loss with netem doesn't work - possibly because of NAT (but delay does work)

    - by tomdee
    I have traffic from a WIFI access point routed via an Ubuntu box. I have two network interfaces which are NATed *filter :INPUT ACCEPT [11:690] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [37:6224] -A FORWARD -s 192.168.2.0/24 -i eth1 -o eth0 -m conntrack --ctstate NEW -j ACCEPT -A FORWARD -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT COMMIT # Completed on Thu Mar 15 13:37:21 2012 # Generated by iptables-save v1.4.10 on Thu Mar 15 13:37:21 2012 *nat :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -j MASQUERADE COMMIT If I run a ping app on an Android device connected to the WIFI network I can happily ping google. If I use netem to introduce some delay tc qdisc change dev eth0 root netem delay 100ms I can clearly see pings taking longer. If I use netem to introduce some packet loss tc qdisc change dev ifb0 root netem loss 50% then I see no change. Packet loss does work fine for locally generated traffic, just not for traffic coming in over the network that's being NATed. Any ideas how to sort this out?

    Read the article

  • iptables question

    - by RubyFreak
    i have a small network, with one valid IP and a firewall with 3 network interfaces (LAN, WAN, DMZ). I want to enable PAT on this valid IP to redirect http traffic to a server in my DMZ. (done) I want to enable MASQ on this ip from traffic that comes from my LAN (done) I want from my LAN as well to access my http server at DMZ. (partially) Question: in the above scenario, i cannot from my LAN, to access my http server in the DMZ, since it has the IP used by the MASQ (the only valid ip that i have). What would be the best option to solve this problem? network interfaces: eth0 (WAN) eth1 (DMZ) eth2 (LAN) /sbin/iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE /sbin/iptables -A FORWARD --o eth1 -d 2.2.2.2 -p tcp --dport 80 -j ACCEPT /sbin/iptables -t nat -A PREROUTING -i eth0 -d 1.1.1.1 -p tcp --dport 80 -j DNAT --to 2.2.2.2 /sbin/iptables -A FORWARD -i eth0 -o eth1 -m state --state RELATED,ESTABLISHED -j ACCEPT /sbin/iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT /sbin/iptables -A FORWARD -i eth2 -o eth0 -j ACCEPT

    Read the article

  • How do I remove/uninstall a corporate VPN?

    - by Metro Smurf
    I have a corporate VPN installed on one of my Windows XP systems that I'd like to completely uninstall. There are no programs listed in the add/remove programs dialog matching the corporate VPN name or similar. I can find the VPN being launched from here: C:\Documents and Settings\All Users\Application Data\Microsoft\Network\Connections\Cm\<Company Name> I can see the VPN connection under network connections: Name Type Device Name Connection Manager ------------------- Connection to <Company Name> Connection Manger WAM Miniport (PPTP) Do I just need to delete the connection from Network Connections? And delete the directory? Or?

    Read the article

  • Track sales and commission with third-party tool

    - by Andrew
    I have a clothing website where I link to various clothing retailers. I have reached an agreement with one of the retailers whereby they will pay a commission to us for every sale they make from traffic that was referred by our site. I need a mechanism for tracking how much commission should be paid to us, that involves as little work as possible to implement from their side. We both have Google Analytics. Option 1: They record a goal in their GA account whenever someone makes a purchase on their site. They see how many completed goals are marked as referral traffic from our site and calculate commission accordingly. The problem with this is that the whole process of calculating and paying commission will be manual. They will need to frequently check how many sales were generated by referral traffic from our site, and probably we will have to chase them for commission payments. Also - since we won't have access to their GA data - we will need to trust that they report all sales accurately. Option 2: Sign them up to an affiliate network like Commission Junction or Google's Affiliate Network, and connect to them through this network. The problem with this solution is that it seems too heavyweight; ideally we don't want to ask a retailer to go through the whole sign up process just to deal with us and pay us commission. I am assuming that there must be some lightweight service that tracks the number of sales by one site and pays commission accordingly to the other site, where the sign up and installation procedure is simple and fast.

    Read the article

  • What are the advantages of OSPF vs nexthop self with iBGP?

    - by Matt Hamilton
    Assuming I have a fairly small network internally, but I have 4 routers each connected out to a different network. The routers are all sat next to each other connected via a switch. Each router uses BGP to speak to the outside networks. There is an iBGP mesh for each router to exchange the routes internally it knows about from each external network. The usual setup is to use OSPF to distribute the connected routes, as the routes via iBGP will still have the next hop set to their original value. What is the advantage of using OSPF in this scenario versus simply using 'set nexthop self' on the routes?

    Read the article

  • Not able to connect to internet in RHEL 5

    - by chankey007
    I just installed red hat enterprise 5 in my laptop and on desktop both. In desktop it is working fine but in laptop it is not showing the eth device. (I tried ifconfig only lo is there). I tried ifup eth0 still nothing happened. The network service in /etc/sysconfig/network-scripts/ifcfg-eth0 and in /etc/sysconfig/network are enable. I had ubuntu in my laptop before and I faced same problem with that too. Is there any problem with my laptop? I have my system on dual boot and in win7 networking is running fine. I am not able to connect to the internet only, other devices are working fine. System conf: Sony vaio E series. 3 GB RAM, intel core i3 2.13 GHZ.

    Read the article

  • Not able to connect to internet in RHEL 5

    - by chankey007
    I just installed red hat enterprise 5 in my laptop and on desktop both. In desktop it is working fine but in laptop it is not showing the eth device. (I tried ifconfig only lo is there). I tried ifup eth0 still nothing happened. The network service in /etc/sysconfig/network-scripts/ifcfg-eth0 and in /etc/sysconfig/network are enable. I had ubuntu in my laptop before and I faced same problem with that too. Is there any problem with my laptop? I have my system on dual boot and in win7 networking is running fine. I am not able to connect to the internet only, other devices are working fine. System conf: Sony vaio E series. 3 GB RAM, intel core i3 2.13 GHZ.

    Read the article

  • Windows VPN not authenticating from ADSL to Wireless link

    - by deanvz
    I have a normal windows VPN on a computer connecting to a 196.201.x.x/24 IP. If this VPN tries to connect from any address in the 41.x.x.x range it cant get there. The server is a normal windows 2008 server, running exchange with a PPPoE IP natted to a public IP on the public gateway of the wireless network as the server is on site and its connectivity is derived from Mikrotik RB's. The computer on the 41 range can traceroute and ping the server, but the VPN does not authenticate. When on the network or any other, the VPN works fine. Is there something that could be configured on the VPN client? All firewall settings of a standard ADSL router have been checked and found to block only ICMP's. Is this a VPN configuration problem or a network issue?

    Read the article

  • Windows user cannot connect via application, but can via Remote Desktop

    - by C. Ross
    I have an application (ASG-Zena) giving an 1385 error (Logon failure: the user has not been granted the requested logon type at this computer) when trying to run a batch job. I have checked on "Access this computer from the network" includes Everyone and Administrators and many others. "Deny access to this computer from the network" make sure that Guest is not listed there. If you still have problems, then maybe make sure that nothing is listed there. Administrative tools...local security policy..security options "Network access sharing and security model for local accounts" there are 2 options either classic or 'guest only'. Mine is set to classic. (These diagnostics come from this post) The account in question is added to the Administrator group on this computer. I know the login is valid because I regularly login to the server via remote Desktop. What other settings should I check?

    Read the article

  • Windows 7 PPTP VPN problem

    - by Marco Martins
    Hi, I'm currently using an win 7 as an network server at my home. I've created some shared folders wich can be accessed easily from any pc on my network (win and mac computers) recently I decided to turn on the win 7 pptp to access remotely to my server from anywhere. the problem is with that on, on my router my server ip change, acording to my ipconfig on the cmd my router gets the ip from a "PPP adapter RAS (dial in)". when that happens I cannot access to the shared files over the lan on my mac, but i can connect to the vpn but again can't access to my files. (i've tried connecting to the vpn from another network and it worked, even the file share) anyone can help me? thanks

    Read the article

  • How do I access an Ubuntu VirtualBox guest at a static IP from an OS X host?

    - by David Siegel
    How does one configure an Ubuntu guest to use a static IP that's visible to an OS X host, and ensure that the static IP is independent of the host's network configuration? I previously used bridged networking for my guest, but I'm constantly moving my host between networks so the guest IP is always different. First, I tried setting the guest network configuration to NAT and forwarding host port 1022 to guest port 22, so I could at least ssh to a fixed address (localhost:1022): $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/Protocol" "TCP" $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/GuestPort" 22 $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/HostPort" 1022 Then, $ ssh localhost -p 1022 ssh: connect to host localhost port 1022: Connection refused But this didn't work (guest has no network access with NAT and OS X refused the connection, as you can see). I'd love a general solution that would let me communicate with my guest at a fixed IP.

    Read the article

  • recent unreliable wireless connection

    - by gabkdlly
    Recently, my internet connection over wireless ( via a Netgear KWGR614 router ) has become unreliable, on both a Dell laptop running Ubuntu 10.04 as well as my Desktop running Ubuntu 10.10 . The problem does not seem to occur on a laptop running Windows Vista, nor on a Desktop running Windows 7 ( this machine is connected with an ethernet cable ). The problem does not seem to occur on my Openmoko Freerunner ( running Android 1.5 ), though I hardly ever use this device to connect over WLAN, so the problem may have just slipped by. On my main Ubuntu Desktop, I have tried the following wireless devices: a Longshine PCI card ( an old device with an RTL8180L chip ) a D-Link DWL-510 PCI card ( this device threw warnings in dmesg ) a USB device from MSI ( US54EX ). Usually my wireless network shows up in the network manager with a normal signal strength, even when the connection speed is slow or the connection gets reset ( asking me to click connect to re-authenticate my wireless connection ). I have observed this problem with a Netgear KWGR614 Router ( with the manufacturers firmware ), as well as with a TP-LINK TL-WR741ND router running OpenWrt. Taking a look at my routers logs, I find many instances of the following line: Tuesday,04 Jan 2011 03:53:01 [TCP SYN Flood][Deny access policy matched, dropping packet] I know that the Netgear router is susceptible to denial of service attacks, as I have previously been able to disrupt its operation by putting an nmap scan into a while loop. I use WEP or WPA to encrypt the wireless network. Is it possible that someone is jamming my signal ?

    Read the article

  • Tunneling over HTTP

    - by Morgan
    Hello, I have a network at work that is locked behind a firewall and Internet connection is available only by using a proxy server. At work, I can connect to databases that are distributed across the network. However, at home, I cannot connect to the proxy server or the databases. How can this be done? I can access my workstation via LogMeIn, so I can install anything on it. I thought of installing some kind of tunneling mechanism in my workstation. Then, at home, I could connect to this mechanism, which would in turn do the required connections. So essentially, what I'd like to do can be represented by the following diagram: Home = Workstation = Database. For example, whenever I connect to, say, 10.140.0.1:1234 at home, this would be redirected to 10.140.0.1:1234 of my Workstation, because 10.140.0.1:1234 is only available through the corporate network. NOTE: I'm using Windows XP.

    Read the article

  • Brother DR350

    The Brother DR350 is a great toner cartridges that has several features that make it stand out from the rest of the printer cartridges available in the market today. The dedicated drum unit of the Br... [Author: Noah Houde - Computers and Internet - May 09, 2010]

    Read the article

  • setting up bridged adapter for VPN server

    - by B. VB.
    I have an Ubuntu linux Linode server that I am trying to install OpenVPN on. I'm following the tutorials (which, it turns out, are quite incomplete). auto br0 iface br0 inet static address 192.168.0.10 network 192.168.0.0 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off When I add this chunk in my /etc/network/interfaces, and I restart networking, my eth0 interface does not have an IP and I cannot get on the network (I need to use a buggy, slow, and annoying AJAX term to do damage repair). Why does adding this screw everything up? Any tips on how to set up this bridged adapter?? Thanks in advance!

    Read the article

  • Impacting the Future through Collaboration at Alliance 14

    - by Jeb Dasteel-Oracle
    We’re hearing good things about the Alliance 14 conference held in Las Vegas by the Higher Education Users Group (HEUG) back in March. For those of you who aren’t familiar with Alliance 14 conferences, they are global events dedicated to enhancing and educating its members and the world on how higher educational institutions can utilize Oracle applications to change how they do business. The HEUG is an all-volunteer organization made up of individuals who collaborate with Oracle as part of the evolving higher education industry. Conference participants network with peers from other institutions (regionally and globally) to share the challenges; discuss solutions and ideas, and collaborate on HEUG strategic initiatives. The HEUG enables each institution to be a part of the ever-changing Oracle landscape. Watch the video below and hear directly from the attendees about their experience with Oracle and how being part of the HEUG has allowed them to  collaborate with one of their most importance resources... and with each other. Oracle is committed to fostering a strong and independent network of user groups worldwide. Currently over 900+ groups provide dynamic forums for customers to share information, experiences and expertise. If you’re interested in more information or joining an Oracle User Group, click and become part of a vibrant network of engaged users finding the best ways to get the most value from their Oracle investment and collaborating to provide a unified feedback voice to Oracle. Catch you next time, Jeb

    Read the article

  • Asus EEE PC 1005HA (XP Home) refuses to connect to Virgin Mobile MiFi

    - by Dennis Wurster
    My client has an Asus EEE PC model 1005HA, and we're attempting to connect it to the WiFi network created by a VirginMobile MiFi unit. They also have a MacBook Pro with Snow Leopard that has absolutely no issue connecting to the MiFi. The specific symptom is that the netbook fails to lease an IP address from the MiFi unit. I supply the 12-digit numerical password (WPA) to the netbook, it throws a 'waiting for network' dialog with an indeterminate progress indicator, and then times out. Update: We've determined that this behavior has stopped when the EEE PC and the MiFi unit were taken out of the client's home, and to a different home that didn't have an existing wifi network. Similarly, when taken to a third location that didn't have wifi, the EEE PC and MiFi got along swimmingly. My current theory is that the existing wifi networks and the wifi leg of the MiFi unit are on the same channel and competing with one another. Perhaps the MacBook Pro has the capability to overcome this interference, while the EEE PC doesn't.

    Read the article

  • What is a SIP 'Gateway' and how is different from a SIP Proxy/Registrar?

    - by Shrey
    Recently I started looking at SIP implementation for a future work. I was reading (Googling) about what SIP means and how to go about implementing a end-to-end SIP enabled VoIP network. What I did not get is what use does a SIP Gateway is for? How different is it with respect to SIP proxy servers or a SIP DNS/Locator like server? I understand probably QoS would be one primary factor - like dedicating a set bandwidth for SIP/VoIP specific I/O over a network. Anything else? Can anyone help me with any other hints/pointers? I fully understand that is quite a basic question - but I really couldn't find any text which could clear my doubt about what 'Gateway' would mean in SIP context and what differentiates it from other SIP based network components (like Softphones, Proxies etc). Thanks a lot.

    Read the article

  • From Co-op to fulltime help with salary negotation [closed]

    - by Peter
    Hey I'm a coop student that worked at a particular medium size printing company for 8 months. I had a good time it was lax, sometimes insufficiently challenging but none the less I learned a whole lot. I stuck with them for another 5 months (including this month) at the same rate I was paid then, doing testing work, tool development, taking care of emergencies when the lead developers were away, and other smaller projects and now bigger projects and problem handling (bad printer output etc.). I know their website inside out (ecommerce), and I know their printing software inside out and have made many changes to them both without a hitch. I have also done a lot of refactoring of the existing code base which as far as Im concerned, I believe am the only one to do those sorts of restructuring even though there is constant talk about it. I guess the unit testing paid off and lets me see the value in modularity if even a tad more. Never the less I have faith in my skill and the restructuring I did turned out better than I had imagined . Now the problem is that I finish school next month and so I asked for a full time spot the month after. They have been expanding and have hired a new guy a few months after my coop spot, and just now they hired a new guy to deal with the CRM application. The lead developer who wrote all of the software had left 5 months ago so it was up to all of us to learn what he had done over 4 years (including db, networking). So now I'm afraid that if I assert myself for a salary similar to the other guys, which I believe I am certainly on par with, that I would be seen as ingrateful. It's hard to flip a switch and say, hey double my pay, although when I'm working with their bread and butter (printers) and writing new features, refactoring the whole application for extensibility. I love it regardless of pay. I also feel maybe I'm replaceeble, although nobody knows the website better than myself and the lead web dev (not by a long shot), and nobody knows the printer software/drivers better than myself. I just thought they would have brought up a raise earlier on, and now it feels like they don't value my work. I'm also tired of worrying about it. I think my question is, well what do I do next?

    Read the article

  • Week in Geek: Google Finds 9,500 New Malicious Websites Per Day

    - by Asian Angel
    Our last edition of WIG for June is filled with news link goodness covering topics such as a new printer bomb malware that wastes reams of paper, Google bars a website that converts YouTube songs into MP3s, Ubuntu plans to drop GRUB 2 to implement UEFI SecureBoot compatibility, and more. Image courtesy of Google Online Security Blog. How to Make Your Laptop Choose a Wired Connection Instead of Wireless HTG Explains: What Is Two-Factor Authentication and Should I Be Using It? HTG Explains: What Is Windows RT and What Does It Mean To Me?

    Read the article

  • Solution for lightweight LAN peer discovering?

    - by DevilWithin
    I built a library for purely cross-platform programming. My games made with it run fine in Android , Pc, Linux, Mac etc. The networking capabilities are provided by ENET library, therefore all communication between my apps is not TCP or UDP compatible, but only in the custom protocol, even tough its based on the UDP ultimately. I don't think its possible to do what i want with ENET, thats why I ask here for help! Lets say I have the same game running in my Android phone, my laptop and my pc. They are all in the same wifi network, and therefore in a LAN, whether its Wifi hotspot(?) or the household router. I need each of those 3 peers to discover the other two in the network. This is meant only to find the IP of alive apps in the LAN network, to be able to host multiplayer games between them. I can only think of one effective way to do this, UDP broadcast, wait responses, but if that is the solution, i need something small, since its the only purpose of the implementation. Other way could be to try to connect to all IPs in the LAN address subrange, but I don't think the OS would be with me on this one :p Sorry for the long question!

    Read the article

  • Remote Control Home PC from Corporate Work PC

    - by muncherelli
    Here is my situation: I am currently on a Windows XP workstation at work. I have an android tablet that I use to splashtop into my home PC. I would like to be able to use my work keyboard and mouse to control my home PC while I am splashtop'd into it using my tablet. My work PC is on a corporate LAN, and not on the same network as my tablet. The company I work for provides wifi for personal devices, but they are not accessable to the internal network. I thought about going the Synergy route, however that would require my home PC to be able to connect to my work PC which isn't really possible. The opposite would work though, if I could reverse connect the server to the client, but the Synergy software doesn't really support that. I do have a couple linux boxes running at home, so I can ssh into my home network and tunnel ports via SSH if needed. With what I have, how can I accomplish seamless keyboard and mouse sharing between my work PC and either my home PC or my android tablet?

    Read the article

< Previous Page | 286 287 288 289 290 291 292 293 294 295 296 297  | Next Page >