Search Results

Search found 19446 results on 778 pages for 'network printer'.

Page 292/778 | < Previous Page | 288 289 290 291 292 293 294 295 296 297 298 299  | Next Page >

• What are good and bad jitter times for a LAN

  - by garyb32234234

  Ive just ran jperf (frontend to iperf) on our network between 2 workstations, its recorded jitter between 0.033ms and 0.048ms. Is this good or bad? Are there more variables that i would need to consider to make the decision? EDIT: TCP/IP Ethernet LAN 43 PCs 1 server, 100Mbits main switch, various small 8 port switches, test was done using UDP, Its a Windows Domain. I want to instal a few voip softphones on the workstations, see how many i can use that reliably work, im testing a few different workstations around the network to see where the best quality network paths are. Will also change some equipment if i identify bad connections.

  Read the article

• How do I 'see' an external USB drive connected directly to my Broadband Router?

  - by The Cougar Kid

  This is a very frustrating problem! I have a small home network with several dual boot Ubuntu / Windows computers. I have recently upgraded my Broadband connection and the new router permits the direct attachment of an external USB drive which can back up all of the household's computers. There are no problems when booted under Windows, and there were no problems with older versions of UBUNTU, but since upgrading to 11.10 I can no longer "see" the drive. I used to find it via Network / Windows Network / Home / name of Router, but under 11.10 the same method yields an error message Unable to mount location Failed to retrieve share list from server. Can anyone help please? Starting Nmap 5.21 ( http://nmap.org ) at 2011-12-21 10:06 GMT Stats: 0:02:02 elapsed; 0 hosts completed (1 up), 1 undergoing Service Scan Service scan Timing: About 50.00% done; ETC: 10:10 (0:01:56 remaining) Nmap scan report for 192.168.1.254 Host is up (0.0097s latency). Not shown: 998 filtered ports PORT STATE SERVICE VERSION 554/tcp open rtsp? 7070/tcp open realserver? Service detection performed. Please report any incorrect results at http://nmap.org/submit/ . Nmap done: 1 IP address (1 host up) scanned in 152.38 seconds sudo tail -n 30 /var/log/syslog [sudo] password for alaric: Dec 21 10:05:42 UPSTAIRS2U wpa_supplicant[882]: WPA: Group rekeying completed with 00:01:3b:8b:63:1a [GTK=TKIP]

  Read the article

• Using Hamachi VPN to connect to Linux VM at home

  - by Cameron Verotti

  I have a CentOS 5.10 Linux box at home running on VMWare, with Windows 2008 as the host. I have set up a Hamachi VPN so that I can connect to the Host server from work, I attempted to add a second VNIC to the VM and bridged it to the hamachi Network Interface. I spun up the VM and checked eth1 with ifconfig and its throwing me a ipv6 address not a ipv4. I want to hook this VM up so that I can run a ssh command from work to the VM. MY network at home is all on Local 198.168.. hence the need to make a VPN network like Hamachi. I cannot seem to find anything that tells me or helps me with tunneling my Linux VM via Hamachi. Any help would be fantastic!

  Read the article

• Can Squid 2.7 proxy gzipped content

  - by Tom Styles

  We have a forward proxy for our network which is Squid 2.7. This is managed for us by a third party. We noticed recently that http requests going from our network to the web were having the Accept-Encoding header removed. This was resulting in all web traffic across our network (approx 8000+ PCs) being uncompressed even though the browsers and server on each end were capable. We have asked the third party to look into this and they have said it is because Squid 2.7 does not support compression. I understand this to be true but I was under the impression that the compression happened on the webserver rather than the proxy. So... Can Squid 2.7 proxy and/or cache content that is gzipped? If it can, how/why might it be configured such that the Accept-Encoding header is being removed?

  Read the article

• How can I make the NetworkManager work?

  - by Yang Jy

  I am running a version of RHCE6 on my laptop, and lately I've been trying various stuff about network configuration through command line. Last night, I tried removing the NetworkManager using "yum remove NetworkManager" from the system, so that I could have more control of the network through the command line. But the result is, I didn't manage to configure the wireless connection through wpa_supplicant, and I need wireless connection during my travel to another place. So I need the wireless function back as soon as possible. I typed " yum install NetworkManager", some version installed, but I don't get to have an icon on the taskbar, and of course, the network doesn't work. The package I previously removed(about 24MB) was much larger that the one I just installed(about 2MB), so I think some dependencies must be missing. How could I install all these dependencies? Please help!

  Read the article

• Routing between two subnets. (Need Solution)

  - by rehanplus

  Need help according to scenario given: Client end PCs: 400 + Network : Server 1 (Linux) : 192.168.2.0/24 (For Application, Internet not working) GW: 192.168.2.1 Clients: 192.168.2.1 - 254 Server 2 (Linux) : 192.168.3.0/24 (For Internet users) GW: 192.168.3.1 Clients: 192.168.3.2 - 254 Server 2 is connected to DSL Broadband. Server 1 and Server 2 both are on same physical network i.e. Same switches. Current issue: i have to deploy a file and print server but this server will be accessed by both (192.168.2.x and 192.168.3.x) one same workgroup. as both subnets are on same switched network. Limitations: Currently there is no hardware routers and firewall. Need to complete this task with Linux / Windows / AD. Tested / Worked so far: Configured one PC with two NIC's With the IPS: NIC 1 : 192.168.3.2 GW: 192.168.3.1 Subnet: 255.255.255.0 NIC 2 : 192.168.2.2 GW: Empty Subnet: 255.255.255.0 Kindly provide any solution what should i do to get sharing enable on both Subnets. Thank you All

  Read the article

• Can only connect to IIS site through localhost

  - by Rembrandt Q. Einstein

  I'm building a web service for my company's iPhone application, and everything's been working smoothly by running tests through localhost on the development machine. I'm now in the phase where I need to test connections from other computers within the network, and any connection other than localhost gives me a 404. My internal IP, 127.0.0.1, and computername all get 404 when connecting from any computer, either the one the site's hosted on or any others on the network. Telnet can get through to port 80, and I've temporarily disabled all firewalls on this machine (I do not have control over the external firewall, but I'm only testing connections within the network) Does anyone have a clue why this is happening? I was able to connect to the web service from other computers when hosted on a Mac via Apache, but because I'm now using a SQL Server connection I'm restricted to using IIS for Windows Authentication. Googling only provided answers related to firewalls, and mine is disabled note: I cannot use Anonymous Authentication, but even in testing that it did not affect the issue.

  Read the article

• ubuntu server in a vm, can't connect to internet

  - by jessh

  I'm attemtping to host my own development web server in a virtual box guest, Ubuntu Server. I would like this virtual machine to be accessible from not only my home network, but outside the LAN as well. As such, I've set up a static IP (so I can later forward ports to this static IP.) My virtual box settings have this vm only using one adapter -- in bridged mode. Here's what my /etc/network/interfaces looks like: iface eth0 inet static address 10.0.1.203 /*this is outside the DHCP range*/ netmask 255.255.255.0 gateway 10.0.1.1 network 10.0.1.0 broadcast 10.0.1.255 dns-nameservers: 8.8.8.8 8.8.8.4 Here's what the output of ifconfig looks like: https://dl.dropbox.com/u/2241201/locker/ubuntu.png My Host is a mac mini, running OS X 10.7. From within the guest, if I ping google.com: $ ping google.com # outputs 'ping: unknown host google.com' immediately Why am I unable to access the web?

  Read the article

• Rate of UDP packet loss over WLAN

  - by Martin

  While testing something with TFTP I noticed lots of timeouts (and slow speed as result) when I used my WLAN - and no problems when using a network cable. A quick test program sending/receiving UDP revealed that there are about 3-5% packets lost. While it's obvious that WLAN has to be less reliable than LAN, I have no knowledge what loss rates are considered 'normal' - and when there is a need to further investigate the network infrastructure. Are there 'typical' packet loss rates on WLAN (and other network technologies e.g. PowerLAN, WAN, ...? Thanks

  Read the article

• Able to send, but not receive from gmail.com within Outlook 2003 (0x800CCC0F)

  - by matt_tm

  In my home network, I'm able to access my @gmail.com and @otherdomain.com accounts via POP3 from Outlook 2003. When accessing from my office network, I'm not able to receive, but am able to send. I get the following error: Task '[email protected] - Receiving' reported error (0x800CCC0F) : 'The connection to the server was interrupted. If this problem continues, contact your server administrator or Internet service provider (ISP).' The POP3 is set to 995 (using SSL), SMTP to 465 (using SSL), Logon using SPA is NOT enabled. There is NO change I make on my system from the office to home network, except my local, internal IP address changes.

  Read the article

• Wifi doesn't connect if I'm upstairs

  - by user11233

  Hello there, I'm finding that Wifi connects when I'm in the living room, where the internet router etc is. But if I try to connect upstairs it is a no go. Booting in Windows 7 (dual boot :D ) I find that Wifi connects. I find this very confusing and have it since the install. Please help! Kind regards. #sudo lshw -c network *-network description: Wireless interface product: PRO/Wireless 5100 AGN [Shiloh] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 00:21:5d:1a:63:58 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=2.6.35-26-generic firmware=8.24.2.12 ip=10.0.0.4 latency=0 link=yes multicast=yes wireless=IEEE 802.11abg resources: irq:49 memory:de200000-de201fff Hope it helps! Hello guys, just tried to connect internet upstairs and to my surprise it does connect. Don't know exactly why. Only thing I've done recently is input the codes said bij Oli. Two things I've done on my own 1: installed Jupiter and 2: installed laptop-mode-tools. I really don't know if this can effect my internet but it's the only thing I can think of. Thanks for all the help, really appreciate it :) PS If someone thinks it might be helpful for others I would like to help find a 'real' solution to this problem. Just post down what I need to post here and I will try my best to help.

  Read the article

• Can't Remote into Windows Server

  - by Brian

  Hello, I have a Dell server wired into the router. I was able to connect to it with my laptop (laptop is wireless) before my router died. My verizon router went kaput, and I got everything else back up and running on the wireless network other than the remoting in feature, even though I can access the server through windows explorer just fine. Any ideas why? What do I need to check? UPDATE: Interesting scenario, Network Discovery is off; I turn it on and save, but for some reason, even after that, network discovery is turning itself off... no idea why that is happening? Thanks.

  Read the article

• Clustering Strings on the basis of Common Substrings

  - by pk188

  I have around 10000+ strings and have to identify and group all the strings which looks similar(I base the similarity on the number of common words between any two give strings). The more number of common words, more similar the strings would be. For instance: How to make another layer from an existing layer Unable to edit data on the network drive Existing layers in the desktop Assistance with network drive In this case, the strings 1 and 3 are similar with common words Existing, Layer and 2 and 4 are similar with common words Network Drive(eliminating stop word) The steps I'm following are: Iterate through the data set Do a row by row comparison Find the common words between the strings Form a cluster where number of common words is greater than or equal to 2(eliminating stop words) If number of common words<2, put the string in a new cluster. Assign the rows either to the existing clusters or form a new one depending upon the common words Continue until all the strings are processed I am implementing the project in C#, and have got till step 3. However, I'm not sure how to proceed with the clustering. I have researched a lot about string clustering but could not find any solution that fits my problem. Your inputs would be highly appreciated.

  Read the article

• Simple server status page hosted externally available for users

  - by Chris

  I am looking for any kind of script - can be asp or php or any other web language - that gives me the ability to log outages and the current state of the network for our organisation. This would be similar to any major Telco's "Network Status" page, but I just want to tell the user's out there if the systems are up and running and have a history of recent outages. This would be for our remote user's so they could go to a webpage (externally hosted from our main site) and see that we are currently having problems with our network. What are other people out there using?

  Read the article

• Making document storage in Sharepoint a breeze (leave the Web UI behind)

  - by deadlydog

  Hey everyone, I know many of us regularly use Sharepoint for document storage in order to make documents available to several people, have it version controlled, etc.  Doing this through the Web UI can be a real headache, especially when you have multiple documents you want to modify or upload, or when IE isn’t your default browser.  Luckily we can access the Sharepoint library like a regular network drive if we like. Open Sharepoint in Internet Explorer (other browsers don’t support the Open with Explorer functionality), navigate to wherever your documents are stored, choose the Library tab, and then click Open with Explorer. This will open the document storage in Explorer and you can interact with the documents just like they were on any other network drive J  This makes uploading large numbers of documents or directory structures super easy (a simple copy-paste), and modifying your files nice and easy. As an added bonus, you can drag and drop that location from the address bar in Explorer to the Favorites menu so that it’s always easily accessible and you can leave the Sharepoint Web UI behind completely for modifying your documents.  Just click on the new favorite to go straight to your documents.   You can even map this folder location as a network drive if you want to have it show up as another drive (e.g N: drive). I hope you found this as useful as I did

  Read the article

• Does my DLink DNS-323 need to reside on a "192.168.0.0/24" subnet?

  - by Raymond

  I've installed two brand new 2-tib drives in the DLink and plugged it in to my network. I set my router's static address table to include the MAC address of the device; however it doesn't ever "show up." Do I need to use the custom software to administer this device? Do I need to use a "192.168.0.0/24" network in order for this device to work (asking because it states that if DHCP isn't detected, it will default to an address in that range; and my network is not in that range).

  Read the article

• Is it possible to pick out what applications that should run through a VPN in Ubuntu 9.10

  - by user31257

  Hi, I'm using Ubuntu 9.10 and I'm wondering if it is possible to pick out what applications that should use a VPN. Say for example that I want to route Transmissions connection through a VPN, but I also want to be able to access my computer over SSH via my usual static IP-adress ( running the SSH- deamon over my normal internet connection) . Is there anyway to do this? As I've been searching the web I found that at least it is possible to set whether you want both your internet connection and your "local network" to go through the VPN or if you want just the "local network" to go through it. I'm using the network-manager-pptp with the pptp- protocol.

  Read the article

• ubuntu 11.10 can't find wireless after waking from sleep

  - by Colleen

  I've tried a lot of proposed solutions, most of them adding files to /etc/pm/config.d, as well as WiFi stops working after waking from suspend and nothing has worked. hardware info: [colleen@colleen-HP ~]$ sudo lshw -C network [sudo] password for colleen: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 06 serial: 2c:27:d7:b1:ea:67 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:41 ioport:4000(size=256) memory:c1404000-c1404fff memory:c1400000-c1403fff *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:0d:00.0 logical name: wlan0 version: 00 serial: 8c:a9:82:99:48:8c width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-21-generic-pae firmware=39.31.5.1 build 35138 ip=192.168.0.4 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:48 memory:c5500000-c5501fff Is anyone else still having this problem? The two solutions I haven't tried are installing wicd and upgrading because I've heard both are kind of unstable/buggy and wicd frankly scares me.

  Read the article

• Is looking for Wi-Fi access points purely passive?

  - by Aric TenEyck

  Say I carry a Wi-Fi enabled phone or laptop through an area where there are WAPs. Assuming that I don't actively try to connect to them or otherwise interact with them, is it possible for the owner of that WAP to know that I was there? I'm asking this in the context of my earlier question: Looking for MACs on the network I was talking with a friend about my newfound ability to detect phones (and other devices with MAC addresses) on the network, and he pointed out that it might be useful to detect unknown phones on the network; I could use that data to track down anyone who was in my house and brought a Wi-Fi phone with them. So, if I set up a logging fake WAP with no security or encryption, can I glean any useful information about the devices that come into the house? Assuming that the thief doesn't actively try to connect...

  Read the article

• Installer script removed a buch of 64-bit files and replaced them with 32-bit ones, how do I get them back?

  - by ILikePizza555

  I ran this installer script to get some drivers for my printer, however I noticed that it started removing some of my programs, as well as 64-bit system files, and started replacing them with 32-bit ones! Luckily, I managed to cancel the operation before it did any serious damage. I also noticed that offical PPA's for 32-bit files were added. Should I remove them? So how do I get these files back?

  Read the article

• Wireless Connection unstable with multiple devices connected

  - by KingIsulgard

  My wireless network works perfectly when only 1 device is connected. Super fast, full strength. But as soon as multiple devices are connected to the wireless network the connections become unstable (constantly losing connection with the internet, not the network itself). It's quite annoying. I have a Sitecom Wireless 300N XR Gigabit Router WL-306, which should be a decent router so I'm guessing there must be something wrong with my configuration. Does any of you know what might cause this? Thanks

  Read the article

• Windows Vista Backups?

  - by skaz

  I am trying to configure a Windows Backup on Vista but don't see some capabilities I would expect to be there. For one, it looks like I can only select a Local Drive or a network share. I want to use a local drive, but I want to use a sub folder of one of the drives. Must I really pick the root? As a work-around, I made a network share to the local drive, thinking I could then pick network share. However, when I do this, I am prompted for credentials to hit the share, and none work. However, the share works Explorer, and it works from other computers, so the access is configured correctly. Is there any way to do what I am trying to do? Thanks.

  Read the article

• what are the vulnerabilities installing openvpn client on a customer's unattended server?

  - by senorsmile

  We run Pfsense as our primary firewall. We also have OpenVPN server running on that box to allow us to remotely connect to our network. My question is: if we have a customer's mostly unattended server that we want to access remotely, what security vulnerabilities are there to installing openvpn on the customer's server as a client connecting to our network. Presumably, we would want to limit/restrict that server's access to the rest of our network. How do we lock openvpn down and are there ways to detect abnormal activity coming from an openvpn client?

  Read the article

• Multiple IPs from one router

  - by ergoen

  I would like to know if it is possible (and if so, how) to configure a router running dd-wrt (or openwrt) to supply connected devices with two ip addresses. The network looks like this: [Internet] | [Router] | | [Comp1] [Comp2] ... My ISP provides me with enough public IP adresses to give all devices on my network one each. The easiest way to set that up is to just use the router as a switch. This will however lead to problems with some LAN based applications. I would still like to use Samba-shares between the computers as well as a vpn server. What I am looking for basically is if it is possible to use the router as a DHCP server for a local network (let's say giving IP adresses 192.168.1.xx to connected computers) while at the same time passing through public IP addresses to each as well?

  Read the article

• How can I disable internet for a specific interface in Windows 7?

  - by MGSoto

  I have two NICs on my machine, one which connects to my network and has my internet connection. The other connects to a buddy next doors network with his internet connection. I don't want Windows magically deciding which internet connection to use, I want it to use mine. I've had some success by blanking out DNS servers for his connection, but then I also lose hostname resolution on his network and I realize this doesn't solve everything 100%. How can I force Windows to use only my connection while avoiding the use of a router?

  Read the article

< Previous Page | 288 289 290 291 292 293 294 295 296 297 298 299  | Next Page >