Search Results

Search found 13947 results on 558 pages for 'television shows'.

Page 41/558 | < Previous Page | 37 38 39 40 41 42 43 44 45 46 47 48  | Next Page >

  • Is there an audio recording application/tool that has Tivo-like functionality?

    - by Bob
    I do a lot of live speech recording that requires me to quickly jump back and then transcribe a particular piece of the audio, then go back to recording again, while still maintaining the full audio file. So Far I've done this by splitting the audio and running one line to a recorder (for the whole audio), and one to my computer. Then I use something like Audacity to record, and then stop/go back whenever I hear something worth transcribing. This requires me to stop the recording, then start it up again and I end up missing chunks of the speech I'm listening to. Is there a tool that would let me rewind, then listen again and continue listening at a buffered distance from the audio recording, the way Tivo does with television shows?

    Read the article

  • Can enabling a RAID controller's writeback cache harm overall performance?

    - by Nathan O'Sullivan
    I have an 8 drive RAID 10 setup connected to an Adaptec 5805Z, running Centos 5.5 and deadline scheduler. A basic dd read test shows 400mb/sec, and a basic dd write test shows about the same. When I run the two simultaneously, I see the read speed drop to ~5mb/sec while the write speed stays at more or less the same 400mb/sec. The output of iostat -x as you would expect, shows that very few read transactions are being executed while the disk is bombarded with writes. If i turn the controller's writeback cache off, I dont see a 50:50 split but I do see a marked improvement, somewhere around 100mb/s reads and 300mb/s writes. I've also found if I lower the nr_requests setting on the drive's queue (somewhere around 8 seems optimal) I can end up with 150mb/sec reads and 150mb/sec writes; ie. a reduction in total throughput but certainly more suitable for my workload. Is this a real phenomenon? Or is my synthetic test too simplistic? The reason this could happen seems clear enough, when the scheduler switches from reads to writes, it can run heaps of write requests because they all just land in the controllers cache but must be carried out at some point. I would guess the actual disk writes are occuring when the scheduler starts trying to perform reads again, resulting in very few read requests being executed. This seems a reasonable explanation, but it also seems like a massive drawback to using writeback cache on an system with non-trivial write loads. I've been searching for discussions around this all afternoon and found nothing. What am I missing?

    Read the article

  • mount error 5 = Input/output error

    - by alharaka
    I am running out of ideas. After a long period of testing this morning, I cannot seem to get this to work, and I have no idea why. I want to mount a Windows SMB/CIFS share with a Debian 5.0.4 VM, and it is not cooperating. This the command I am using. debianvm:/home/me# whoami root debianvm:/home/me# smbclient --version Version 3.2.5 debianvm:/home/me# mount -t cifs //hostname.domain.tld/share /mnt/hostname.domain.tld/share --verbose -o user=SUBADDOMAIN.ADDOMAIN.DOMAIN.TLD/username mount.cifs kernel mount options: unc=//hostname.domain.tld\share,ip=10.212.15.53,domain=SUBADDOMAIN.ADDOMAIN.DOMAIN.TLD,ver=1,rw,user=username,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,pass=*********mount error 5 = Input/output error Refer to the mount.cifs(8) manual page (e.g.man mount.cifs) debianvm:/home/me# The word on the nets has not been very specific, and unfortunately it is almost always environment-specific. I receive no authentication errors. I have tried mount -t smbfs and mount -t cifs, along with smbmount and such. I get the same error before. I doubt it is a problem with DNS resolution, because logging shows the correct IP address. dmesg | tail -f no longer shows authentication errors when I format the domain and username accordingly. I have played a little with iocharset=utf8, file_mode, and dir_mode as described here. That did not help either. I have also tried ntlm and ntlmv2 assuming it might be a minimum auth method problem, but not forcing sec=ntlmv2 it can still authenticate without errors anymore. smbclient -L hostname.domain.tld -W SUBADDOMAIN.ADDOMAIN.DOMAIN.TLD -U username correctly lists all the shares and shows it as the following. Domain=[SUBADDOMAIN] OS=[Windows 5.0] Server=[Windows 2000 LAN Manager] Sharename Type Comment --------- ---- ------- IPC$ IPC Remote IPC ETC$ Disk Remote Administration C$ Disk Remote Administration Share Disk Connection to hostname.domain.tld failed (Error NT_STATUS_CONNECTION_REFUSED) NetBIOS over TCP disabled -- no workgroup available I find the last line intriguing/alarming. Does anyone have any pointers!? Maybe I misread the effin manual.

    Read the article

  • apache: can't renew ssl certificate

    - by Caballero
    I have Godaddy SSL certificate for one website on my dedicated server running Centos 5.3 / Apache 2.2.3. I have renewed certificate on Godaddy recently, however now it's showing as expired on my website. I've re-keyed certificate since and reuploaded domain.key, domain.crt and bundle.crt (example file names) files to the server, restarted apache, but the sertificate still shows as expired. I'm running out of clues. I've tried replacing content of .crt files with jiberish and restart apache - it's still showing that certificate is expired, even though it shouldn't be picked up at all. I eventually rebooted dedicated server, still no luck. I'm using free SSL check tool http://www.digicert.com/help/ which clearly shows all the green checks except one - certificate is expired. Has someone any idea what might be causing this? Could there be some kind of caching going on here? UPDATE: after running openssl x509 -in domain.crt -noout -enddate I'm getting this output: notAfter=Jun 2 08:16:51 2013 GMT So I asume this means I have the right certificate on the server and yet the old expired one shows on the web...

    Read the article

  • Winamp playing sound but no video

    - by Greg Sansom
    I am having problems playing video in Winamp (the movie I am trying to play is an AVI - not sure if other formats work). I have installed the K-Lite Codec Pack, and the video does work in Winamp Classic. I can also play the video in Winamp on another machine (although I can't remember the exact configuration details of that machine - and I don't think they're relevant). There are a few symptoms: The content of the Video view is either empty, transparent, or displays rendering from other programs. Opening the Visualization view shows the following error: MILKDROP ERROR DirectX initialization failed (GetDeviceCaps). This means that no valid 3D-accelerated display adapter could be found on your computer. If you know this is not the case, it is possible that your graphics subsystem is unstable; please try rebooting your computer and then try to run the plugin again. Otherwise, please install a 3D-accelerated display adapter. Trying to open streams via the SHOUTCast TV plugin shows Error opening video output, and the video does not open. Opening the file with WMC causes the following error (although the movie still plays): Error creating DX9 allocation presenter CreateDevice failed D3DERR_NOTAVAILABLE There are no warnings displayed in Device Manager, although the display adapter is the standard Windows one. Running DxDiag shows no problems (codec for Video listed as XviD 1.1.2 Final). GSpot reports that codecs are installed. System specs: - Windows Server 2008 r2 Standard 64-bit, with latest updates; - .NET 3.5.1 installed; - Winamp v5.6.01 (latest version); - DirectX 11 (Latest version); - K-Lite Codec Pack 7.0.0 (Full); - Machine is HP DC7600 - full specs here. Please comment if there is any more information which will help to diagnose the problem.

    Read the article

  • How do I get 480i resolution for an external monitor in Windows 7?

    - by Carson Myers
    I'm trying to get a laptop video signal to my really old television, so that I can play movies on it. But the TV won't accept the video signal. I found the manual online, and apparently the output has to be 480i. But I don't know how to do that -- Windows 7 will only let me set the resolution down to 800x600. Even if I get it down to 640x480- is that 480i or 480p? How do I tell the difference? How do I switch between them? How do I get the resolution down so low in the first place?

    Read the article

  • getent passwd fails, getent group works?

    - by slugman
    I've almost got my AD integration working completely on my OpenSUSE 12.1 server. I have a OpenSUSE 11.4 system successfully integrated into our AD environment. (Meaning, we use ldap to authenticate to AD directory via kerberos, so we can login to our *nix systems via AD users, using name service caching daemon to cache our passwords and groups). Also, important to note these systems are in our lan, ssl authentication is disabled. I am almost all the way there. Nss_ldap is finally authenticating with ldap server (as /var/log/messages shows), but right now, I have another problem: getent passwd & getent shadow fails (shows local accounts only), but getent group works! Getent group shows all my ad groups! I copied over the relavent configuration files from my working OpenSUSE 11.4 box: /etc/krb5.conf /etc/nsswitch.conf /etc/nscd.conf /etc/samba/smb.conf /etc/sssd/sssd.conf /etc/pam.d/common-session-pc /etc/pam.d/common-account-pc /etc/pam.d/common-auth-pc /etc/pam.d/common-password-pc I didn't modify anything between the two. I really don't think I need to modify anything, because getent passwd, getent shadow, and getent group all works fine on the OpenSUSE11.4 box. Attempting to restart nscd service unfortunately didn't do much, and niether did running /usr/sbin/nscd -i passwd. Do any of you admin-gurus have any suggestions? Honestly, I'm happy I made it this far. I'm almost there guys!

    Read the article

  • OpenSWAN KLIPS not working

    - by bonzi
    I am trying to setup IPSec between 2 VM launched by OpenNebula. I'm using OpenSWAN for that. This is the ipsec.conf file config setup oe=off interfaces=%defaultroute protostack=klips conn host-to-host left=10.141.0.135 # Local IP address connaddrfamily=ipv4 leftrsasigkey=key right=10.141.0.132 # Remote IP address rightrsasigkey=key ike=aes128 # IKE algorithms (AES cipher) esp=aes128 # ESP algorithns (AES cipher) auto=add pfs=yes forceencaps=yes type=tunnel I'm able to establish the connection with netkey but klips doesnt work. ipsec barf shows #71: ERROR: asynchronous network error report on eth0 (sport=500) for message to 10.141.0.132 port 500, complainant 10.141.0.135: No route to host [errno 113, origin ICMP type 3 code 1 (not authenticated)] Tcpdump shows 22:50:20.592685 IP 10.141.0.132.isakmp > 10.141.0.135.isakmp: isakmp: phase 1 I ident 22:50:25.602182 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 22:50:26.602082 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 22:50:27.601985 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 ipsec eroute shows 0 10.141.0.135/32 -> 10.141.0.132/32 => %trap What could be the problem?

    Read the article

  • AFP/SSH stopped working on OS X Server

    - by churnd
    I have 3 Mac OS X servers all bound to AD, all configured in the Golden Triangle setup. All 3 are completely separate from each other in terms of services, but all reside on the same internal network and are all bound to the same Active Directory domain. Two are 10.5.x (latest updates) and one is 10.6.3. Last weekend, all 3 simultaneously stopped allowing Active Directory users access to certain services, specifically AFP & SSH. SMB still works fine on all 3. I asked the AD admin if anything changed, and he said "Yes, we made a change to user accounts to toughen up security", and suggested I use [email protected] instead of just username. This still didn't work. I have completely removed one of my servers from AD, and re-joined, but this didn't work either. I can do kinit from command line and get a Kerberos ticket. sudo klist -ke shows all services are configured to use the correct Kerberos principles. I have been scavenging the logs for any useful info. The AFP log just shows that I'm connecting and disconnecting. The DirectoryService.log shows stuff about misconfigured Kerberos hashes, but my research is showing that's not uncommon. /var/log/system.log isn't showing anything useful that I can see. I'm not sure where to go from here. Any help/ideas appreciated.

    Read the article

  • How do I keep a bridge enabled on a bonded interface?

    - by jlawer
    I'm working on setting up a pair of CentOS 6.3 servers that will run a couple of KVM vms and have come across a problem setting up a bridge on a bond. I am using Mode 4 (802.3ad) bonding on a pair of stacked Dell Powerconnect 5524 switches connecting to R320 servers. There are 2 links (1 to each switch) that form a Link Aggregation Group (802.3ad / LACP bonding). On top of the bond I have VLAN Tagging. I've verified this is a problem on multiple other bonding modes so it isn't just a mode 4 issue. I am testing what happens when 1 link is dropped (ie switch dies, cable breaks, etc). If I don't have a bridge (for KVM), everything works fine, failover happens as expected. If I have the bridge enabled, it works fine until failover (unplugging a cable). When failover happens /var/log/messages shows the slave link going down, followed within a second by: kernel: br1: port 1(bond0.8) entering disabled state The thing is /proc/net/bonding/bond0 shows the link is up as expected (simply with only 1 slave instead of 2). If I plug the cable back in it recovers and brings the bridge back to an enabled state. I actually have tested this while a ping is occuring and if the timing is right a packet will actually leave the system after the link is lost, but before the disabled message occurs. This disabled state I assumed was STP, but I have disabled STP on the bridge configuration and this issue still occurs. brctl showstp br1 still shows the link as disabled when it is running without a slave. I also switched between the nics in the server (I have 2x Broadcom & 4x intel). It doesn't matter which configuration I have. Does anyone know of a way to force the bridge to stay enabled or why its detecting the bond as disabled, when it isn't?

    Read the article

  • server 2008 r2 stuck on installing updates

    - by volody
    I have 2008 r2 64bit server that is stuck on installing updates. It shows message "Please do not power off or unplug your machine. Installing 57 of 61.." This message is shown for 3 hours now. I was trying to connect to this server using mmc. runas /user:AdministratorAccountName@ComputerName "mmc %windir%\system32\compmgmt.msc" RUNAS ERROR: Unable to run - mmc C:\Windows\system32\compmgmt.msc 1311: There are currently no logon servers available to service the logon request. What else can I do? Update: Remote Desktop does not work. It just disappear after entering username and password from Win7-64 computer Update: I have disconected server. Now Server Manager in Roles Summary shows message "Unexpected error refreshing Server Manager: The remote procedure call failed." Event log shows Could not discover the state of the system. An unexpected exception was found: System.Runtime.InteropServices.COMException (0x800706BE): The remote procedure call failed. (Exception from HRESULT: 0x800706BE) at System.Runtime.InteropServices.Marshal.ThrowExceptionForHRInternal(Int32 errorCode, IntPtr errorInfo) at Microsoft.Windows.ServerManager.ComponentInstaller.ThrowHResult(Int32 hr) at Microsoft.Windows.ServerManager.ComponentInstaller.CreateSessionAndPackage(IntPtr& session, IntPtr& package) at Microsoft.Windows.ServerManager.ComponentInstaller.InitializeUpdateInfo() at Microsoft.Windows.ServerManager.ComponentInstaller.Initialize() at Microsoft.Windows.ServerManager.Common.Provider.RefreshDiscovery() at Microsoft.Windows.ServerManager.LocalResult.PerformDiscovery() at Microsoft.Windows.ServerManager.ServerManagerModel.CreateLocalResult(RefreshType refreshType) at Microsoft.Windows.ServerManager.ServerManagerModel.InternalRefreshModelResult(Object state) Update: Manual update hangs on (Installing update 58 of 62...) Seurity Update for Windows Server 2008 R2 x64 Edition (KB979309) Update: It could be an issue with that admin user was renamed

    Read the article

  • Why does my Intel Tolapai network chip not transmit packets?

    - by Hanno Fietz
    I'm trying to deploy an embedded system (NISE 110 by Nexcom) based on the Intel EP80579 (Tolapai) chip. Tolapai apparently integrates controllers for Ethernet etc. on a single chip (Intel homepage). The machine can't get a network connection. Diagnosis as far as I could manage: Drivers drivers from Intel compiled and installed without problems (version 1.0.3-144). Kernel version and Linux distribution (CentOS 5.2, 2.6.18) match the driver's installation instructions. drivers are loaded and show up in lsmod (module names are gcu and iegbe) interfaces eth0 and eth1 show up in ifconfig ifconfig I can bring up the interfaces with fixed IP pinging the interface locally works ifconfig shows flag UP but not RUNNING Link ethtool shows "Link detected: no", "Speed: unknown (65536)" and "Duplex: unknown (255)" Link LED is on on the other side of the cable, ethtool shows "Link detected: yes" and reports a speed of 1000 Mbps, which has allegedly been auto-neogotiated with the problematic device. Network traffic analysis the device does not reply on ARP, ICMP echo or anything else (iptables is down) when trying to send ICMP or DHCP requests, they never reach the other end activity LED is off on the device, on at the other end. I tried the following without any effect: Different cables (2 straight, one crossed), I get the link LED lit up on each. Three different devices on the other end (one PC, one netbook, one router) Fixed ARP table entries on both sides Connecting both network ports of the machine with each other, won't ping through the cable, but will ping locally. Tried straight and crossed cables for that.

    Read the article

  • Windows 7 BSOD on startup

    - by Cristy
    I got a BSOD today after getting home from 11 hours of work... It seems to work in SAFE MODE (sometimes, not always) The BSOD says: SYSTEM_SERVICE_EXCEPTION STOP: 0x0000003b WimFsf.sys - Address FFFFF88001A6B76B base at FFFFF88001A600000, DateStamp 4a5bc362. Sometimes it shows the welcome screen, shows the destkop for a few seconds and then BSODs Already did: unplugged all the USB devices reset the CMOS I haven't installed any new software recently. What should I do? EDIT: I've managed to get into safe mode and it seems to works fine. When I go into normal mode it shows the desktop then it freezes... Is it more likely to be a software or hardware problem? EDIT2: I've managed to get into normal mode by disabling all the non-microsoft services & startup programs. One more thing: When I shut down my PC, on the "Logging off" screen appear some artifacts. I don't think it's because of my graphics card cause I've opened Black OPS and it worked fine. It's so strange... It still BSODS on startup (but there a ~=10% that it will not), and when it doesn't BSOD's it works fine...

    Read the article

  • Best FFDShow settings for upscaling SD content to 1080p HD?

    - by Richard
    Hi there, I'm running Windows Media Center 7 with ffdshow-tryouts for the decoding of many of the popular video formats. It works great. I've now upgraded my television from SD to 1080p HD and, naturally, I've still got a large number of existing MP4/XviD/DivX items of content which is in SD. I'd like, therefore, to modify the settings of ffdshow so that they are upscaled to 1080p as best as possible. I appreciate that they won't be as good as their HD equivalent - but on the flip side, I'm pretty certain I can do more than just resizing the picture to get the best possible output. Can anyone recommend the best settings in ffdshow to do this? For example, should I apply a sharpen mask? Or Noise Reduction? Or Deinterlace? Alternatively, would it be better to keep them at their current resolution and let the TV (Samsung Series 5 LE32C580) do the upscaling? Thanks.

    Read the article

  • Sound problems in Windows 7

    - by Plastkort
    hi! I hope I reached the correct forum for this question. I have a media computer with a third party audio card (Soundblaster audigy SE) I use a coaxial digital audio cable connected to a Onkyo TX SR508. if I use normal audio, the sound seems very low, I have to set volume atleast to 62 in my amplifier to hear anything, however if I set digital SPDIF I have no means of controlling the audio volume from the PC (only from the amplifier) and this can be nasty if I toggle between movies that uses Digital AC3/THX and movies wihtouth, if I look at movies capable of AC3 the volume gets VERY loud if amp is set to 62, 32 is more than enough volume when using passthrough. so this bothers me is how can I get the same amount of volume with or without digital output? I tried also other soundcards, internal red light Digital audio cable... if I connect to my television I get ok sound on any sound source via HDMI... help :)

    Read the article

  • Internet Explorer / Windows 7 does not want to show HTML file from local network drive

    - by Jaanus
    Setup: I have Windows 7 running inside VirtualBox on Mac OS X host. I have a shared drive with some HTML files, that I am mounting as a local drive W: in Windows, from the VirtualBox server \VBOXSVR. I want to look at them with a browser in Windows. Chrome in Windows 7 opens and shows those HTML files just fine (file:///W:/welcome.html). But Internet Explorer does not, and shows this error instead of the files: Internet Explorer cannot display the web page What you can try: [button Diagnose Connection Problems] More information This problem can be caused by a variety of issues, including: Internet connectivity has been lost. The website is temporarily unavailable. The Domain Name Server (DNS) is not reachable. The Domain Name Server (DNS) does not have a listing for the website's domain. If this is an HTTPS (secure) address, click Tools, click Internet Options, click Advanced, and check to be sure the SSL and TLS protocols are enabled under the security section. For the internet zone in the status bar, it shows: Internet | Protected Mode: On IE settings are a mystery to me, and I could possibly get it to work by tweaking IE settings, but I don't know which ones. How do I make IE show the same files that Chrome is happy to show? (Chrome showing them means that the files themselves are fine, there is something about the setup that just makes IE be a diva.)

    Read the article

  • Queries passed to SQL Server are getting corrupted

    - by adrianbanks
    We are experiencing a bizarre error with our application at a customer site. We have managed to narrow it down to the point where we can replicate the behaviour using just Management Studio and SQL Server. We have two machines, A and B: +------------+ +--------------------+ | [A] | | [B] | | Management | -------------- | SQL Server 2008 R2 | | Studio | | Enterprise x64 | +------------+ +--------------------+ We are running a SQL script in Management Studio on machine A against the SQL Server instance on machine B. We are not actually executing the script, just parsing it. Most of the time, the parse operation works fine. Occasionally (seemingly randomly), the parse operation fails with a syntax error. The error message shows the part of the script with the error, which appears as some SQL from the original script that has been truncated and has random characters appended to it. An example: The original SQL: SELECT DISTINCT ST.TABLE_NAME as TableName FROM INFORMATION_SCHEMA.TABLES AS ST INNER JOIN INFORMATION_SCHEMA.COLUMNS AS SC ON SC.TABLE_NAME = ST.TABLE_NAME WHERE ST.TABLE_TYPE = 'BASE TABLE' AND SC.COLUMN_NAME = 'Identity' AND ST.TABLE_NAME != 'dtproperties' ORDER BY ST.TABLE_NAME The SQL that is in error (as reported by SQL Server): SELECT DISTINCT ST.TABLE_NAME as TableName FROM INFORMATION_SCHEMA.TABLES AS ST INNER JOIN INFORMATION_SCHEMA.COLUMNS AS SC ON SC.TABLE_NAME = Sa? The above example shows how the query is being corrupted. It doesn't always happen, and is not always the same bit of SQL that causes the error. Parsing this script against another SQL Server instance produces no errors, showing that the script is fine. It appears that something is corrupting the SQL that is being received the the server. This leads me to think that the problem lies either with the client end or in the transmission of the SQL from the client to the server. I have a SQL trace from the period where an error occurs, which shows the SQL has been corrupted when SQL Server receives it. We have been unable to track down any possible cause of this behaviour, and so cannot find a fix. Because the errors occur seemingly randomly, it is also very hard to generate reproduction steps to submit a bug report. Any ideas?

    Read the article

  • Ideal laptop specs for a Computer Science Masters student?

    - by Ayush
    I have a HP pavillion core 2 duo 2 GHz and 4 GB RAM, and it is painful to use this machine for any kind of coding. Eclipse (especially Juno) literally takes 5 minutes to load. And even after that, everything is lagy. Apart from school stuff, I also use my computer as a television. I watch Hulu, Netflix, YouTube etc in 720p, and this laptop gets hot as hell and the fans are loud enough to wake somebody up from deep sleep. I DON'T use my laptop for Gaming or Video/Photo Editing. I'm looking to buy a new laptop (in which most widely used IDEs would work smoothly and playing hi-def videos wouldn't be too much for the machine to handle) any suggestions (on hardware specs) would be greatly appreciated. Thanks

    Read the article

  • Network Sharing Issues

    - by Mark Kramer
    I have two computers I want to have on a network share together (so the laptop can print through the desktop's printer). These are both connected to the same router. (One wired and one wireless) And they both have the same workgroup name. However, when I type "net view" in the command prompt, the only computer that shows up is the computer I type the command into. How do I get these computers to be shared with each other? Update: The tower is running Windows XP, the Laptop is running Windows 7. I have disabled the Firewall on both until I get this set up. Update 2: Typing the command net view on my desktop is acting very strangely. Noe sometimes it only shows itself on the list of computers, sometimes it shows itself and the laptop and sometimes it doesn't work at all and displays system error 6118. I typed net view into the command prompt on the Windows 7 laptop and both computers showed up, so I went to connect to the desktop from the laptop and it said the dekptop could not be found, even though it is showing up int he list of shared computers. Here are supporting pictures (these are coming from the laptop)

    Read the article

  • Laptop white screen on power-up. Still displays via HDMI output

    - by Inno
    my wife's laptop recently started displaying a white screen. It doesn't show post or anything, just a white screen when it's powered on. However, it works normally with HDMI output to our television. I took it apart and fiddled with both ends of the display cable, but I either didn't fiddle correctly or that's just not the problem. I also noticed that the screen won't turn off anymore when the laptop is closed. Is there a name for the mechanism that controls this function, so I can try and locate it? My guesses are that the problem lies with the screen itself or the display cable, but I'm curious if there's anything else I might be overlooking. Also of note is that the left hinge is partially broken. The corner of the plastic computer case broke off, so the hinge is exposed and doesn't stay in place. I've tried holding it in place, wiggling it around, tapping various parts of the computer, but the white screen remains.

    Read the article

  • how do you view / access the contents of a mounted dmg drive through TERMINAL hdiutil diskmount

    - by A. O.
    My external USB drive failed. I made a .dmg image file of the drive using disk utility. Later I was not able to mount the .dmg image. I used terminal hdiutil attach -noverify -nomount name.dmg diskutil list diskutil mountDisk /dev/disk4 then received the following message: Volume(s) mounted successfully However, I cant see the drive or access its contents through Finder. DUtility shows the drive as ghost but I still cant mount it using diskutility. Terminal tells me that the drive is mounted and constantly shows it in the diskutil list. pwd is not the mounted .dmg image. I dont know how to enter into the mounted image drive to see its contents. So in case what I said sounds like I see the files in the mounted image no this is not the case. I do not know how to access or even change the pwd within Terminal. I was hoping to see the mounted drive tru finder but I do not see that. So I need help as to how to find a way to access the mounted image drive if it was really mounted. Terminal says that it was and it shows it under diskutil list as a /dev/disk4. Can someone please help me access the files on this drive?

    Read the article

  • initrd problem and Kernel panics after openSUSE 11.2 upgrade.

    - by unixbhaskar
    Once I have done the upgrade form openSUSE11.1 to openSUSE11.2 by doing this: zypper dup Now I tried to boot the system and it failed sync with VFS and kernel panic, so clearly a initrd problem . if I'm not mistaken. Now a bit of explanation about the problem: while upgrading it shows me the error updating initramfs( I forgot the exact error or might be warning).Oh yeah it shows some grub warning too. I have had been doing that from a chroot environment.. with all the required file mounted in proper place in the chroot environment. Now .after bit googling and painfully looking the susegeek.com forum and opensuse.org forum I have decided to recreate the initrd ...but the fellow called "mkinitrd" is real real crap as I hev been pointed out by few forum members. I tried to make an initrd image by myself, failed to do so .as it shows error that device not found( if I boot into suse live cd and mount the partition ) then I tried from the chrooted env and it says "there is no space left on the device" A bit bemused :( yeah most of you pointed it right may lack of knowledge of mine. Kindly suggest me and show me steps to do it correctly and get opensuse11.2 up and running. TIA

    Read the article

  • Volume is no longer showing in Raid Controller BIOS and in Windows

    - by Gordon
    Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. From their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

    Read the article

  • Windows Displays Double the Actual Installed Physical Memory

    - by Andrew Barber
    I have a server I've installed Windows Web 2008 R2 on, which is reporting that I have double the physical memory installed as is actually the case. In msinfo32 "Installed Physical Memory" shows as 2x what ever the actual installed amount is, though "Total Physical Memory" shows the correct amount. The "System" info window shows installed memory as 2x, with the correct amount in parenthesis listed as the "usable" amount). This server mistakenly had Windows Web 2008 (32-bit) installed on it just previously, and that OS also reported the same faulty information as Win2K8R2 is reporting. BIOS reports the correct amount, memtest was run on this server before installation, and a previous Windows 2000 instance installed on this system also reported the correct amount, as I recall. Server operation seems to be fine as well (it's only trying to use the correct amount of memory). The server is a generic pizzabox running on a SuperMicro X6DVL-EG with dual Xeon-3.2's. Memory installed are 4 matching mt18vddf12872g-335c3 sticks (1GB pc2700 DDR ECC REG cl2.5) This behavior occurs whether two or all four are installed. So, has anyone seen something like this before? Have any idea about what's causing it, and how I should be concerned about it? Everything else seems good so far, and I'll be upgrading the memory before putting the server into service, but I don't want to spend too much time/money/effort on the server if it's got something odd going wrong here. UPDATE: There was a question I ran into regarding memory sparing in the BIOS and a possible (buggy) effect thereof; however, flipping that bit back and forth in the BIOS revealed that isn't the issue. Still flummoxed a bit about this one, though I still have seen no negative impacts. Post-Answer Update (January 13, 2011): Upgrading the system with new, larger memory has fixed this issue.

    Read the article

  • Strange Behaviour with Unicode Characters in Windows

    - by open_sourse
    Ok, I do not know if this is a programming question, but it certainly is a technical one so I am asking it here. I was working on some internationalization stuff in my PHP code, and in order to ensure that my generated HTML shows up Unicode correctly based on the encoding and stuff I decided to add some Chinese text to my PHP page, which then echoes it into the browser to complete my test case. So I went into google and typed "Chinese", copied the first Chinese text that the search returned (which was ??/??). I then copied it into Notepad++ which is my editor, and to my surprise showed up as boxes similar to [][]/[][]. So I thought the encoding in Notepad++ was messed up and I changed the encoding to UTF-8 and UCS, neither worked. I did it fresh in a newly encoded file, still I got the boxes. The same content when I paste into Google and StackOverFlow (like I did in this posting) shows up correct Chinese! I even opened up Windows Clipboard Viewer and the content is represented in the Clipboard as boxes! I tried pasting it into Windows Explorer address bar and using to rename a file to, but I still get boxes. But it shows up correctly when pasted into my Chrome Browser address bar! Is this a Windows issue? Since I am able to paste it correctly in SO, the data in memory should be encoded correctly right? But if that is the case why does it show up as boxes in the Clipboard Viewer? I am confused here...By the way I am using Windows XP with SP3. (I am asking this question here, even if it is not programmatic, because it is preventing me from running my programming test cases..)

    Read the article

< Previous Page | 37 38 39 40 41 42 43 44 45 46 47 48  | Next Page >