Search Results

Search found 2692 results on 108 pages for 'ts gateway'.

Page 67/108 | < Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >

  • Bonding: works only from one link

    - by Crazy_Bash
    I would like to install bonding with 4 links. but only one of them is active. eth4 is always active. the others simply don't work. those are my configs: DEVICE="eth2" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth3" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth4" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth5" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE=bond0 IPADDR=<ip> BROADCAST=<ip> NETWORK=<ip> GATEWAY=<ip> NETMASK=<ip> USERCTL=no BOOTPROTO=none ONBOOT=yes NM_CONTROLLED=no /etc/modprobe.d/bonding.conf alias bond0 bonding options bond0 mode=4 miimon=100 updelay=200 #downdelay=200 xmit_hash_policy=layer3+4 lacp_rate=1 Linux: Linux 3.0.0+ #1 SMP Fri Oct 26 07:55:47 EEST 2012 x86_64 x86_64 x86_64 GNU/Linux what i've tried: downdelay=200 xmit_hash_policy=layer3+4 lacp_rate=1

    Read the article

  • Messenger Thinks My Ip is Invalid

    - by Umut Benzer
    Hello. I am using Windows Live Messenger 2009 on Windows 7. I am using a 3G modem (ZTE Propietary USB Modem) I connect to the Internet using a software my ISP provided me. In last three days, my Messenger started to disconnect. Here is what I observed and tried to do: 1- I can browse web, can do FTP transfer etc. and obiviously have a valid IP. 2- I can sign in to Messenger (appear offline) but when I change my status to anything other then appear offline, Messenger says my connection to service has been lost. (However, it exists.) 3- When I run, MSN Connection Troubleshooter, it says my IP is invalid. When I click repair, it says repaired and just after that, I run the troubleshooter again, and it says my IP is invalid again. (However, it is valid and I am browsing the net.) 4- If I connect the Internet through eterhet or wireless there is no problem at all. 5- I re-installed Messenger (deleting all settings manually through registry and folders), re-installed all drivers and software related to USB 3G Modem. It doesn't work. And then, I took a full backup then formatted entire computer, installed a fresh windows 7, after 5 minutes, the same problem occured. What do you recommend? What can I do? Addition As seen on screenshot, it says Server IPv4 adress is 0.0.0.0 It seems like a problem, I don't know if it is. If it is, how can I solve it? Here is what I get, when I netstat. PPP adapter TTNET internet: Connection-specific DNS Suffix . : IPv4 Address. . . . . . . . . . . : 217.174.39.122 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : 0.0.0.0 Wireless LAN adapter Wireless Network Connection 2: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : ege.edu.tr Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 16: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 13: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter 6TO4 Adapter: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 9: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 11: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 12: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 14: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 17: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 25: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 20: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 18: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 19: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 22: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 21: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 15: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 23: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e74:2448:3909:2a2c:eb7b Link-local IPv6 Address . . . . . : fe80::2448:3909:2a2c:eb7b%30 Default Gateway . . . . . . . . . : Tunnel adapter Local Area Connection* 24: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{CFFCFEDB-6B53-42E0-B091-548B9ADE9C9D}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 26: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 27: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 29: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 31: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 28: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 32: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2002:d9ae:277a::d9ae:277a Default Gateway . . . . . . . . . : 2002:c058:6301::c058:6301 Tunnel adapter Local Area Connection* 30: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{157CF713-B3AC-4701-87A9-14C23CA60AAB}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.ege.edu.tr: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{0D3CD01B-0993-4B37-89B8-12557ECF484D}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . :

    Read the article

  • HOw to give static ip to router from window XP LAN

    - by Captain Planet
    I have the USB modem internet connection. I am using ICS sharing in XP to share my internet connection. ON window XP LAN i have set up the LAN IP as 192.168.137.1 255.255.255.0 Now i have joined the cable from that XP LAN to another LAPTOP running vista Now if set the LAN on VISTA to get ip automatically them internet don't work but if manually set the ip to 192.168.137.3 255.255.255.0 gateway 192.168.137.1 Then my internet works But i want to join that LAN cable from XP to rouer so that i can use router to divide internet. But i don't know how i can give static ipto router because i think somehow that LAN on XP is not giving the IP address

    Read the article

  • static routes, cisco ASA, remote locations

    - by Jeff
    192.168.3.1(ASA) - 192.168.2.1(ASA) - ( internet ) - 192.168.1.1(ASA) DomainController, FS, Exchange 192.168.0.1(ASA) - above is a rough idea what my network setup looks like. each internal ip (192.168.x.x) is located behind an ASA. Each location has a different gateway for the internet. They all talk to the 192.168.1.1 network for dns, dhcp, dc, exchange and so on. They can only see the 192.168.1.1, they can not see each other. In my Static Routes on my 192.168.1.1 ASA, should i have them configure as follows? example: 192.168.x.x 255.255.255.0 Locations_Internet_Gateway_IP OR 192.168.x.x 255.255.255.0 Main_Locations_Internet_Gateway_IP not sure which configurtation is correct, thanks in advance for any help!

    Read the article

  • Static Routes and the Routing Table

    - by TheD
    This is very much a learning question if someone would be happy to explain a couple of concepts. My question is - the default routing table that exists in, in my case, a default Windows 7 install, what do each of the routes in the table do? Here is a screenshot: The 10.128.4.0 is just a route I've added while messing. I understand from a question I posted on Superuser the first route is just a default route that will route all traffic for any IP to my default gateway on my Interface in use. But what about the others? And how would the routing table handle a machine with multiple NIC's, perhaps connected to two different networks, or maybe even two NIC's on the same network so a VM can have a physical Network card instead of each VM sharing the hosts. Thanks!

    Read the article

  • how can I stop my sonicwall TZ-210 (SonicOS Enhanced 5.5.1.0-5o) from responding to arp queries on the wan subnet?

    - by IsaacB
    My sonicwall TZ-210 is answering arp queries on the wan subnet (which my isp doesn't like), basically mapping all the wan ips to its own mac address, causing network havoc since it is not set to route those back to the main isp gateway. How the heck can I turn this behavior off? I have already entered in all wan subnet ips in the static arp cache and left them 'unpublished' which I presumed would mean that it did not bother answering arp queries for them. Apparently it did not do the trick. Arp queries are still being answered unfortunately. What can I do? Any suggestions?

    Read the article

  • New power supply and now HDDs are not recognized.

    - by Michael
    So I upgraded to a new X4 ULTRA power supply that was recommended to me by a local TigerDirect store. After installing it along with a new liquid cooling system, I booted it up and it automatically fried my CD Drive. After that I noticed that the OS wouldn't start and figured out that none of the 4 HDDs in my computer were being recognized by the BIOS. I feel them spool at a steady pace and have tried new cables and connections but to no avail. I triple checked all of the connections and cables and have no idea what is wrong. This isn't the first time I changed a PS or CPU cooling system but I am at a dead end. Any ideas, aside from buying a USB HDD reader and seeing if they are all fried? Also, this is a stock Gateway mobo with the mobo USB connections already dead. Could the new PS have fried the SATA connections??

    Read the article

  • Confusion about HSRP Groups

    - by Kyle Brandt
    If I have a router that has several LANs on it, and each of these LAN is attached to a second router, do I need to use different HSRP groups for each LAN? With this set up, each virtual gateway will be on a Layer 2 segment. And within a router, no interface will have multiple gateways. So, For example: Router 1: F0/0: ip address 192.168.1.2 255.255.255.0 standby ip 192.168.1.1 F2/0: ip address 192.168.2.2 255.255.255.0 standby ip 192.168.2.1 Router 2: F0/0: ip address 192.168.1.3 255.255.255.0 standby ip 192.168.1.1 F2/0: ip address 192.168.2.3 255.255.255.0 standby ip 192.168.2.1 Will this work, or do I need standby 1 ip 192.168.2.1 on the F2/0 interfaces? Since according to the RFC, the group number of the packet is in the HSRP multicast packets, my guess is that I don't need different groups, and that multiple groups are only needed when they are all on the same Layer 2 segment. However, I haven't been able to find this setup....

    Read the article

  • Windows Server - Dual NIC Bandwidth Pooling

    - by tsilb
    I have a Windows Server 2008 machine with dual NICs. Both are plugged into the same switch in a typical one-switch, one-gateway home network. This server is used almost exclusively for inbound connections. It hosts a web server (IIS 6), SQL server, and file server (via LAN UNC paths and mapped drives). How do I make best use of inbound bandwidth across both NICs? For example, if I connect to it by hostname and one of the interfaces has high traffic, I'd like the new connection to use the other interface.

    Read the article

  • configure cisco catalyst 3560g with an egress uplink

    - by imaginative
    Currently my setup has our egress uplink connected directly to an external interface on a linux router/firewall/nat gateway. Since the linux box is a single point of failure, I've since setup two openbsd boxes using carp+pf+pfsync in order to gain some additional redundancy. the problem is, I only have one egress uplink (it's still a single point of failure) but need to get it to speak to the active carp node in my openbsd cluster which will server as my new router/firewall/nat cluster. Is there anything specific I need to do on a 3560G in order for me to be able to: 1) Drop the egress uplink into a port 2) Drop one link from the switch to a firewall 2) Drop a second link from a switch to the firewall This is so if one box dies, the other still has the egress link to the switch. Is putting them into one VLAN enough? Anything else that needs to go into the configuration for this setup to work?

    Read the article

  • Problem with VPN using 2 Wire Router with a Linksys Router.

    - by Hiram Hubbard
    I am having a problem with a VPN between a 2 Wire router and a Linksys router. 2 wire is the client PC using Linksys Quick VPN software and Linksys RVS4000 is the server. The PC is not the issue. It works on a different network not using 2 wire. Also the Linksys RVS4000 is not the issue, 3 other user can VPN to it with no problem not using 2 Wire. The problem is with 2 Wire. The client PC is getting this error: "The remote gateway is not responding" What configuration changes are needed on the 2 Wire router (port, UPNP, etc...) and what changes are needed if any on the Linksys RVS4000? Thanks.

    Read the article

  • FortiGate firewall configuration with /30 and /28 networks

    - by slyderc
    I have fiber coming in from a new ISP which is being handed off via Ethernet on a single physical port. I'm having doubts about how to approach the configuration on my FortiGate 200A firewall because I've been given a /30 containing the ISP's gateway and another /28 for external IPs I can use: x.y.76.12/30 (.13 is the GW) x.y.76.64/28 (public IP space) How do I configure the FG200A's WAN1 interface to be aware of the two networks? As I only have one physical ISP port, will I need to plug it into a switch to break-out two cables and use a DMZ port on the FG200A for setting up the /28? Thanks in advance for your insight!

    Read the article

  • SMTP port open - but not open

    - by Frederik Nielsen
    As some of you might know, I am setting up an exchange server. Now I ran into another problem: I cannot connect to the SMTP service from outside the server! The ports are opened in the gateway device (a ZyXEL USG50), Windows firewall is off. I see the packets travekl through the ZyXEL firewall, and I can also see the packets with wireshark on the server, so I know they are getting all the way in to the server. I also know it receives them, and sends out the reply - and this is where things go bad! Analyzing with wireshark, I get these errors in the return packets: Header checksum: 0x0000 [incorrect, should be 0x0779 (may be caused by "IP checksum offload"?)] And: Acknowledgment Number: 0x8e3337d1 [should be 0x00000000 because ACK flag is not set] What the (sorry my French) hell is going on? I really cant figure it out.. Thanks in advance.

    Read the article

  • 2 routers, both DHCP, no IP assigned

    - by piobyz
    I can't get DHCP to assign IP to my wireless devices. My network config is as follows: Nanostation5 Linksys WRT350N, which is connected with Nanostation via its INTERNET port. Nanostation: LAN IP Address: 192.168.1.20 WLAN IP Address: 192.168.0.79 Network Mode: Router and is getting its IP via DHCP from my ISP Netmask: 255.255.255.0 Gateway IP: 192.168.1.1 LAN Network settings: IP Address: 192.168.1.20 Netmask: 255.255.255.0 Enable NAT: YES ENABLE DHCP Server: YES Range 192.168.1.100 ~ 250 Netmask: 255.255.255.0 Enable DNS Proxy: YES Linksys: Internet Connection Type: DHCP Router IP: 192.168.2.1 Subnet Mask: 255.255.255.0 DHCP: Enabled Start IP: 192.168.2.100 ~ 120 Advanced Routing: NAT: Enabled What I can do is connecting manually with this config: IP: 192.168.2.101 Subnet Mask: 255.255.255.0 Router: 192.168.2.1 DNS: 192.168.1.20 Search domains: WRT350N I want to be able to connect to both routers independently(now its 192.168.1.20 for Nanostation, and 192.168.2.1 for Linksys) and connect any wireless device using DHCP. What should be IP ranges, masks, etc. on both devices?

    Read the article

  • Permanent Routes Centos Questions

    - by user65053
    So with a little help I figured out how to setup these routes and I can set them in rc.local route add -net 208.82.236.0 netmask 255.255.255.0 dev ppp0 metric 1 route add -net 208.82.236.0 netmask 255.255.255.0 dev eth0 metric 10 my question is being that the first route is ppp0 as soon as I disconnect the modem the route is dropped how do I maintain the route or make it permanent so that next time the modem connects it will follow the route. Currently after ppp0 disconnects the route is dropped netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface laxapx03.o1.com * 255.255.255.255 UH 0 0 0 ppp0 208.82.236.0 * 255.255.255.0 U 0 0 0 eth0 10.0.1.0 * 255.255.255.0 U 0 0 0 eth0 169.254.0.0 * 255.255.0.0 U 0 0 0 eth0 default 10.0.1.1 0.0.0.0 UG 0 0 0 eth0

    Read the article

  • ISP Load Balancing with ISA 2006

    - by Bill Best
    I understand that ISA 2006 has an integrated Network Load Balancing feature. We also recently acquired a second internet line through a second service provider. I know it is possible to purchase a NLB router for using both incoming lines but this is not the route we would like to take if at all possible. Thus, is it possible to have two ISA 2006 servers each with there own external connection, Load balanced to be viewed as one gateway? My thought was to have two ISA servers each with three NICs, one external, one internal and one for cross communication. I am under the impression that this should work but was hoping someone else has had experience with it.

    Read the article

  • Cisco ASA - VPN and Hairpinning....

    - by Nordberg
    Hi, We have 2 sites that will be linked by a IPSEC VPN between 2 Cisco ASAs: Site 1 8Mb ADSL Connection Cisco ASA 505 Site 2 2Mb SDSL Connection Cisco ASA 505 Basically, both sites need access to a service at the end of another IPSEC VPN, Site 3, which I plan to terminate at Site 2. This is due to the way the service is sold - it's billed per gateway. So if both Site 1 and Site 2 had their own VPN connection to Site 3, it would cost us twice as much... Anyway, my idea is to have all traffic from Site 1 destined for Site 3 to go via the VPN between Site 1 and Site 2. The end result being all traffic that hits Site 3 has come via Site 2. I understand this is known as hairpinning but I'm struggling to find a great deal of information on how this is setup. So, firstly, can anyone confirm that what I'm trying to achieve is possible and, secondly, can anyone point me in the direction of an example of such a configuration? Many Thanks.

    Read the article

  • Unable to logon using terminal server connection

    - by satch
    I have several W2K3 SP2 servers, admin TS enabled. I discovered this morning, I was unable to logon into some of them. I've a couple of Citrix servers in different farms, a SAP (IA64) app server and a cvs server. All of them show same sympthoms; remote connections are refused. I've been able to logon locally, and terminal server service is up, there are no users (so connections are not depleted). There are no errors in log in most servers. One of the Citrix ones, reported following errors: Event ID 50 Source TermDD Type Error Description The RDP protocol component X.224 detected an error in the protocol stream and has disconnected the client. and Event ID 1006 Source TermService Type Error Description The terminal server received large number of incomplete connections. The system may be under attack. Anyway, I suppose these errors appear because server isn't working, and Citrix users try to logon massively. (I nmap'ed server and port seems up). I've solved this problem rebooting before, but with so many servers affected it seems like a crappy workaround. Any idea about troubleshooting it properly? Thanks in advance

    Read the article

  • Weird routing problems with VPN

    - by Borek
    In our VPN setup I have to add a route to my routing table like this: route add 1.2.3.0 mask 255.255.255.0 172.16.1.1 -p Our internal addresses 1.2.3.x then use 172.16.1.1 as their gateway and both my local internet and work VPN can work at the same time. However, when I disconnect from VPN and reconnect again, I can't ping our servers even though the connection status is "Connected". When I do route print my previously added route is listed but it doesn't seem to work. So I try to execute that 'route add' command again and as expected, it tells me that The route addition failed: The object already exists. But - and that's the point - when I now try to ping our servers again, everything works! So every time, I have to execute this route add command that will fail but fix the issue at the same time. Any ideas what I might be doing wrong? My PC is Windows 7 x64, I am Administrator, UAC is enabled and the command prompt is run with elevated privileges.

    Read the article

  • CNAME rule being ignored

    - by Ben
    On a server with Plesk installed I have added a CNAME rule pointing from one of the sites subdomains to an external website. I have checked the named configuration for that domain name and it shows the CNAME however the sub domain just points to the default server page and ignores the CNAME rule. Named has been restarted and I've also run the rvmng reconfigure-vhost command. I edited another server to test this, on cPanel, and it works fine. The conf file for the domain: ; *** Ts file is automatically generated by Plesk *** $TTL 86400 @ IN SOA ns.example.com. cf.example1.com. ( 1292946742 ; Serial 10800 ; Refresh 3600 ; Retry 604800 ; Expire 10800 ) ; Minimum example.com. IN NS ns.example.com. ns.example.com. IN A xx.xxx.xxx.xx example.com. IN A xx.xxx.xxx.xx webmail.example.com. IN A xx.xxx.xxx.xx mail.example.com. IN A xx.xxx.xxx.xx beta.example.com. IN A xx.xxx.xxx.xx ftp.example.com. IN CNAME example.com. www.example.com. IN CNAME example.com. login.example.com. IN CNAME socialize.gigya.com. example.com. IN MX 10 webmail.example.com. You can see the CNAME rule in the file but it just gets ignored? Thanks in advance for any help.

    Read the article

  • ignore ipv6 router advertisements for static addresses with bonded interfaces

    - by boran
    I need to attribute static IPv6 addresses (not use autoconfigured addresses, and ignore router advertisements). This can be done as follows for a standard interface like eth0 iface eth0 inet6 static address myprefix:mysubnet::myip gateway myprefix:mysubnet::mygatewayip netmask 64 pre-up /sbin/sysctl -q -w net.ipv6.conf.$IFACE.autoconf=0 pre-up /sbin/sysctl -q -w net.ipv6.conf.$IFACE.accept_ra=0 However, how can this be done for bonded interfaces? using the "all" interface does not work. Systems is Ubuntu 10.04, 2.6.24-24-server. If one uses the above sysctl command for the bond0, the networking hangs on boot, because /proc/sys/net/ipv6/conf/bond0 does not yet exist and cannot be written to. One the system has booted /proc/sys/net/ipv6/conf/bond0 exist, so one solution after booting is to add the following to /etc/rc.local: /sbin/sysctl -q -w net.ipv6.conf.bond0.autoconf=0 /sbin/sysctl -q -w net.ipv6.conf.bond0.accept_ra=0 /etc/init.d/networking restart and this has the desired effect, the autoconfig v6 address disappears. Seems like a bit of a hack though, are there better solutions?

    Read the article

  • Firewalling gateways and IDS's

    - by Scott Davies
    Hi, For IDS, I plan to have a Win 2008 server running on the gateway with the majority of roles disabled. I plan to firewall the Internet connection, but I'd also like to install Snort to work as an IDS. However, I am guessing that regardless of the Snort install of the promiscuous Winpcap driver, I won't be able to monitor ports that the firewall blocks. My thinking is that chain of flow is: Internet-Firewall on Win 2008-Winpcap-Snort-internal network Is there a way to still monitor services that the firewall will block (i.e. TCP 445 SMB) ? Perhaps run the data through Snort and then through the firewall ? Thanks

    Read the article

  • Hyper-V virtual machine unable to get IP address from DHCP server running on same physical box

    - by Bronumski
    We have a Windows server 2008 R2 with two network cards running AD, DHCP, DNS and Hyper-V The first nic is setup with a static IP address and DHCP, WDS, and DNS are bound to it. The second nic is configured in Hyper-V to be only used by Hyper-V and has been automatically configured so that only the virtual switch is enabled on the adapter. DHCP and DNS work fine for all physical machines on the network. It also works for Virtual Machines running on another physical box. Virtual machines that are bound to the virtual switch network adapter are unable to get a IP address. If the virtual machine is given a static IP address with correct subnet, gateway and dns everything works. Has anyone else got this working?

    Read the article

  • Virtual NIC on VM couldn't ping externally after Vmotion

    - by ToreTrygg
    Today I vmotioned 5 MS SQL 2005 servers over to a new DRS Cluster. All SQL servers use the "Production_LAN" network and a single virtual NIC of type "VMXNET 3". The first 4 SQL VM (Windows 2003 Standard or Enterprise x32 bit) vmotioned over without a hitch. The last SQL VM I vmotioned (Windows 2003 Standard x64 bit R2) vmotioned over without error, but I upon completion, I could no longer ping the VM. I went into the VM and could not even ping the gateway, however I could ping the loopback. This SQL server is extremely busy in comparison with the previous 4 VM's. I restarted the server and it came back up with the virtual nic working just fine. The build of both servers (vmotioner and vmotionee) is ESX 4.0.0 175625 - So, pre-update 1. Should I suspect the network switch/VM for possibly not updating the mac table on the switch? Anybody else ever have this issue or know what may have caused it? Thank you!

    Read the article

  • What are the advantages and disadvantages of having a hosted firewall?

    - by Roy
    Would you rather have your firewall hosted or in house if you've got the skills to manage it? We currently have 6 remote offices and 2 different ISP's, one private network and our firewall (Watchguard, licenses are due to expire) is also our main gateway. I don't see how a hosted firewall (in this case Fortinet) is going to work for us especially when it's cheaper to buy our own firewall and the transition from one ISP to a new provider will take some time because our current contracts aren't due to expire soon. What are to pros and cons of having a firewall hosted by your ISP in general?

    Read the article

< Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >