Search Results

Search found 2602 results on 105 pages for 'dell vostro'.

Page 97/105 | < Previous Page | 93 94 95 96 97 98 99 100 101 102 103 104  | Next Page >

  • Help with Ubuntu and Windows, separate HDs

    - by LuxuryMode
    Need some major help. Running a Dell XPS/Dimension 630i. It came with "SATA 2 RAID 0 With Dual 500GB Hard Drives." I have installed a new, third non-raided drive and installed Ubuntu on it. So now I have Windows on the original hard drive and Ubuntu Linux on the new HD. When I get to the boot menu where I can select an OS, if I select windows I get an error: "No such drive, no such disk." Also, strangely in the first place, in order to even get to the bootloader menu I have had to disable ALL ports under the RAID config. Unless I do this, I will just get to a never-ending blinking cursor. I have tried every conceivable CMOS config and nothing else works. Tried setting port 3 (the new HD w/ Ubuntu) to first hard disk boot priority. Tried disabling all other ports and enabling the Ubuntu HD port and vice versa. I have some pictures of boot up: first one is strange error i get after messing with CMOS to finally get ubuntu install to work. http://imgur.com/5sqJa then boot menu: http://imgur.com/TWtLq then error: http://imgur.com/TJ1mS. Also, please note that I can actually access all files from the raided Windows drive through Ubuntu.

    Read the article

  • ATI firepro will not detect a second DVI-D monitor

    - by John
    OK so weird issue here. I have previously been running 6 screens off of 3 of the older ATI firepro graphics cards but they had a problem with the heat sink getting too hot and warping the PCB resulting in total failure of the card, to replace my three dead cards I purchased a new-type ATI firepro with the newer heat sink design. I'm only using one at the moment to make sure they've fixed the problem before I waste more money on 2 more cards but this is where things start to get weird. The Firepro's only have one port on them, they connect to two monitors via a splitter cable going from the one port to two DVI connectors for the screens. When I plug two identical monitors in via their DVI inputs not matter what I do windows and Catalyst will only detect one screen. However if I use the VGA input on one of the screens with a VGA - DVI adaptor to plug it in to the card it works fine. This confuses me greatly. I'm currently using the ATI Firepro 2270 Graphics card with identical DELL U2311H screens. I can post the rest of the system spec as well if needed but I wouldn't have thought it would make much difference as it had no problem handling 6 screens before the graphics cards failed. Naturally both catalyst and ATI drivers are the most current version. ATI tech support has been absolutely zero help, they seemed to get stumped as soon as I verified that both screens were plugged in and connected properly. Anyone have any ideas?

    Read the article

  • Winamp has slow /skipping video playback on Windows 7

    - by Roy Rico
    Hello, I have Windows 7 x64 (7600 90-day trial version) and Winamp 5.6 installed. When I play a video in Windows Media Player, the video plays smooth, however when I play a video in winamp, the video is mostly ok when played back at the original size (but not completely), but if I play it back in fullscreen, the playback gets really slow. The video's audio track plays just fine. I have a DELL XPS 420 computer (8GB of RAM) with a Nvidia GeForce 8800 CTS 512 video card. I've updated to the latest drivers. I have the default Windows 7 codecs, and the CCCP codec pack which used to be all I needed under Windows XP to play all types of videos. Are the codecs needed for Windows Y the same? What's going on? UPDATE: As suggested, I turned off Aero and winamp ran just fine again. So I just have to wait for winamp to be rewritten to work with the way Vista/Windows 7 runs? UPDATE 2: Winamp has updated their player, and it works great with Windows 7 now.

    Read the article

  • Generalized strategy for file server virtualization in Xenserver

    - by Jamie
    I'm not shopping as much as I'm looking for some guidance on good idea / bad idea strategies. I'm sure I'm not in the "best practices" budget range. Currently, I have 3 dell poweredges running xenserver in a pool. Each node has a ubuntu file server, serving about 6TB. One is the primary, the other two are rsync targets for backup. The 6TB is stored on their respective local storage disks as an LVM of 3x2tb virtual disks. The fileserver VM disks are also stored on the node local disks. Each node also runs a smattering of light-weight VMs for web, development, windows VMs, and stuff like that. Several of those VM's disks reside on a QNAP NAS to play with live migration. These VM's are often clients of the primary file server (like all the mail, web content, user files are stored on the file server, not on the mail, web, and samba VMs). This all works fine, and is a major step up for us. The downside is that the QNAP is a single point of failure. And the only thing the QNAP is doing is serving migratable VM images, not client data. Someday the poweredge local arrays will be full, and we will have to reinvent ourselves again. Is it wise to have heavywieght vms (like the fileserver, with its 6+ TB disks) on a SAN or NAS? Would it be better to keep the VMs lightweight, have the VM images on a SAN or NAS, and use 2 or more NAS act as NFS-serving file appliances? A hybrid SAN/NAS that can serve iscsi for images and NFS for the client vms? It seems like live-magration would be a misnomer if you have to migrate a fileserver with its entire 6+ TB disk. I recognize there are plenty of ways to skin the cat. We've already skinned it a few ways. What makes sense?

    Read the article

  • Is there a way to force the monitor to power off in Windows 8?

    - by Rune Jacobsen
    I have googled this a bit and looked at powrprof.dll and PsShutdown but I haven't found a way to do exactly what I want to do. You know that power save option that lets Windows turn off your monitor(s) if you haven't touched the system for x amount of time? Well, I have a PC that needs to be on most of the day (and night), and I have to watch it much of the time, so I can't have a short timeout for automatically turning off the monitor. However, once I leave it for a few hours (happens at varying times of the day), I would like to be able to issue a command that puts the computer in this mode. Not sleep mode, not hibernate mode. Monitor off, that is all. I realize of course I could just turn the physical monitor off. That is not what I want. This Dell monitor takes forever to display a picture from a cold state. If it is turned off by the computer not sending a signal - not so bad. Is there any way for me to do this? As mentioned, the OS can do it, so I would find it really useful if I could do it too. :)

    Read the article

  • Recover badly recorded DVDs

    - by CesarGon
    A few years ago (2003-2005) I bought a Sony USB external DVD recorder for my Dell laptop and I used it to burn a lot of discs. Much later, when I tried to use one of these discs, I realised that I could not read it. The disc behaved as if it was scratched or dirty. I tried on a couple of different DVD drives but got the same effect. Sadly, all the discs that I burnt with that recorder suffer from the same problem. Edit. When I read one of these discs with ImgBurn, I get lots of unrecovered read errors in multiple sectors, even at 1x speed. The sectors that cause read errors seem to be quite random; it's not always the same one. I have no idea what could be wrong with the discs. I doubt that they are scratched or dirty; it would be too much of a coincidence that all the discs that I burnt with that recorder got damaged at the same time. Also, they don't show any physical defects. Is there any way to diagnose what the problem is and, hopefully, recover the contents of the discs? Many thanks.

    Read the article

  • Why can't I use my Bluetooth Headset with my laptop?

    - by Michael Haren
    I just received a new Plantronics M50 bluetooth headset. It works great with my phone, but I can't get it working with my laptop. What are the things I should be checking? Here's what I've done so far: It pairs successfully: It's not in multipoint mode--it's only paired to my laptop I've installed all available drivers from Plantronics and Dell I have no (!) in Device Manager (though I don't see the headset there either--would I?) I can "configure" the headset by double clicking on it: "Allow the computer to turn off this device to save power" is unchecked in the Bluetooth radio settings Apps that let me choose the playback/mic device only list my laptop, not the headset [UPDATE] I went into the Bluetooth device's properties and Checked "headset" under the services tab. This was successful but hasn't delivered any functionality as far as I can tell I'd like to use this headset for VOIP conferencing (Goto meeting, Gmail voice chat, G+ hangouts, Skype, etc.) and listening to music (iTunes). Where else should I be digging? Is it possible that this new headset is simply not compatible with computers (i.e. it's only compatible with phones)?

    Read the article

  • Problem uninstalling and installing Java on new pc running Windows 7 64 bit os

    - by Brian Gerrin
    I have a new Dell Studio XPS running Windows 7 64 bit os. I am attending online classes which require IE 8 and Java version 6 build 20. The pc came with IE 8 32 bit and Java 6 build 21 already installed. I tried to uninstall Java using add and remove programs but after about 45 minutes of "Preparing to remove application" I got an error refering to a missing dll file and the uninstall failed. I used a third party program to remove Java and downloaded Java 6 build 20. My problem is when I try to install it I get the box telling me "Installing program ... this may take a few minutes" however after 30 to 45 minutes nothing has happend and there is no indication in the progress bar that anything is happening then all of a sudden the program bar is full and the program is supposedly installed. When I try to run it however it doesn't work. Someone help please! I can't get access to my classwork with out this! Thanks

    Read the article

  • fglrx-legacy-driver not seeing Radeon HD 4650 AGP

    - by Rocket Hazmat
    I am running Debian Squeeze on an old Dell Dimension 8300 box. It has an AGP Radeon HD 4650 card. I use this machine to mine bitcoins, and today I noticed that the machine had rebooted! My precious uptime! Anyway, my miner wouldn't start, so I figured might as well update my graphics driver, maybe that would fix the issue. I went to amd.com and downloaded the newest driver (12.6 legacy), but after installing it, aticonfig gave an error: aticonfig: No supported adapters detected I uninstalled the driver and figured I'd try to install it from apt. AMD has dropped support for the HD 4000 series in fglrx, forcing me to use fglrx-legacy-driver (currently only in experimental). In order to install this, I had to update libc6 (and some other important packages, like gcc), I had to use their wheezy versions. I finally got fglrx-legacy-driver installed, but I still got: aticonfig: No supported adapters detected Why isn't the driver finding my video card? I have a hunch it has something to do with the fact that it's an AGP video card. Here is the output of lspci -v (why does it say Kernel driver in use: fglrx_pci?): 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV730 Pro AGP [Radeon HD 4600 Series] (prog-if 00 [VGA controller]) Subsystem: Advanced Micro Devices [AMD] nee ATI Device 0028 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16 Memory at e0000000 (32-bit, prefetchable) [size=256M] I/O ports at de00 [size=256] Memory at fe9f0000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at fea00000 [disabled] [size=128K] Capabilities: [50] Power Management version 3 Capabilities: [58] AGP version 3.0 Kernel driver in use: fglrx_pci EDIT: fglrx 12.4 seems to work. Thing is, since I am on kernel 3.2, I need to apply this patch to common/lib/modules/fglrx/build_mod/firegl_public.c. I thought ATI dropped support for the 4xxx series after 12.4. Why doesn't 12.6 legacy work?

    Read the article

  • No sound Ubuntu 10.10 (have SB Live! card)

    - by Chris Frazier
    I am new to Linux/Ubuntu and I just installed 10.10 on my Dell Desktop PC that was running Windows XP. The PC is about 5-6 years old and the sound card it has is a SoundBlaster Live! card. The Sound Preferences recognizes the card as [SB Live! Value] EMU10k1X. It is currently set to Analog Stereo Duplex. I tried multiple other sound configurations and nothing works. No sound but some clicks come out of the speakers. I ran the system test and during the audio tests the same thing happened, just clicks and pops. I tried to play some music with Rhythmbox and when it tries to play a track it tries for several seconds and then just closes itself, or sometimes just doesn't play. I ran a check for drivers, but the only driver it found to install was for my nVidia video card. It did not show any drivers for the sound card. Does anyone have any idea what I need to do to get the sound to work?

    Read the article

  • Flickering dual screens in Virtual Box Ubuntu 13.10 Guest

    - by alexleonard
    I have Ubuntu 13.10 x64 installed as a guest in VirtualBox (under a Windows 8.1 host) and have the settings for the virtual machine setup to run with a monitor count of 2, 128MB video memory and 3D acceleration enabled. In my guest I have the virtual box additions installed (which allowed me to have two 1920x1080 screens). Here's a screenshot of my VM settings. My laptop is an Asus N550JV which has both Intel's HD Graphics 4600 GPU and Nvidia's GeForce GT 750M. By default though I believe the Intel GFX card is being used to render the VM. When I boot up the VM it loads perfectly on dual screens, however whenever I move the mouse from one screen to the other (I have a Dell S2340L running over a HDMI connection as a second screen) the screen flickers. I've tried a variety of settings changes in both Ubuntu and the VM settings, but cannot seem to stop this screen flicker. I also used the NVidia control panel in Windows to force the dedicated graphics card to always be used but found that the display driver sometimes crashed whilst working in the VM, resulting in my VM session being destroyed, so I figured it's better to stick with the Intel GFX as that appears to be more stable. I also tried without 3D acceleration but that was much worse, and if I ran the VM with a low amount of graphics memory it really struggled. Here's my dmesg output: http://pastebin.com/1LJuYWMj (not sure if this is helpful in this situation). I read some posts suggesting changes to /etc/X11/xorg.conf but I don't appear to have an xorg.conf file. There were also a few posts (though related to Synergy) suggesting running xset -dpms but this command doesn't appear to have had any effect for me. As an additional note, I'm finding that window drawing in the guest is a little laggy/glitchy. For example, quickly scrolling through a web page may result in parts of the viewport displaying original content. Certainly I notice drawing issues most in the web browser, but it also impacts other software with parts of the window not being drawn when, say, switching between accounts in thunderbird. Any suggestions greatly appreciated!

    Read the article

  • Windows 7 64-bit Google Chrome Makes Desktop Unresponsive

    - by Meengla
    For the past 1-2 weeks my desktop becomes unresponsive sometimes. The problem seems to happen as I load a page in Google Chrome; it could be any page though today it happened when I tried to load a page with Flash content in it. The problem is not consistent and there is no pattern. I can do a virus scan using some software (not antivirus installed--never needed that) but I strongly suspect it is some software I installed or some Windows Update. This is a very powerful Dell Optiplex 990 with 16GB RAM, so Memory shouldn't be an issue. When the problem happens the cursor becomes spinning even over the taskbar and control alt delete takes a long time. Eventually I get a message that 'this program is not responding' with end/close and 'cancel' icon. But repeated end or cancel does nothing. Then the menu for ctrl alt del comes up. The rest of the applications keep running fine though I can't get to them because the cursor is the wait-cursor. What is happening? How can I find what exactly caused the problem? Thanks.

    Read the article

  • I think my laptop just died

    - by Joel Coehoorn
    I have a Dell 1330M that as of about 15 minutes ago will no longer POST. What happened was I was working, stepped away for a moment, and when I came back it was turned off. I thought that was odd, but turned it on and things seemed fine. About 1/2 hour later it crashed and restarted, but came up fine again. It did this once more. At this point I was starting to get worried, but I hadn't had any problems with the laptop before and every crash was after doing some work in a virtual machine that I don't often use, so I at put the blame there. It didn't feel like it was overheating anywhere and there's no ozone smell of overheated electronics. Then it crashed a final time and now when I turn it on all I see is a bright screen with a bunch of vertical lines (noise). I've tried removing the memory sticks one at a time, but I get the same result with either memory stick in either slot. With no memory at all it stops earlier in the POST process and the screen is completely blank (black, no backlight). As I type this, I hear a double beep from the system about once every 10 minutes. I'm pretty sure the hard drive is fine because it fails during post, before anything off the drive is needed. The power supply seems good because the screen is nice and bright. It's not the RAM because swapping that around made no difference. The leaves motherboard (which I doubt and can replace) and CPU (which just might be changable). Any ideas? Is there any hope for this laptop? I'm rather fond of it and I'd have a hard time replacing it with anything near as nice.

    Read the article

  • System Center 2012 VMM UI is very slow

    - by Grant
    I've recently setup system center 2012 a new server 2008 r2 server which I'm using for virtual machines. Everything seems to be working fine, and the virtual machines are nice and fast. But the Virtual Machine Manager interface is always excruciatingly slow. Sometimes taking up to 15 seconds moving between screens. It's very frustrating trying to use it when a task that just involves a couple clicks ends up taking several minutes. Pages that have a lot of form fields seem to take the longest to load - such as the page to change hardware settings of a virtual machine. Is this just normal performance for VMM? If not, where can I look to find what is slowing it down. Nothing else on the system seems to suffer. I can load and use Hyper-V manager with no noticable slowness. Even programs like event viewer that are usually rather slow seem to load fairly fast. Only the system center programs seem slow. Server is a Dell R710, 2x16 core opteron 6274 processors, 96GB RAM. OS drive is 2x500GB 7.2k RPM SAS drives in RAID1 (opted for the less expensive 7.2k drives since pretty much everything is stored on the SAN). Am I just being impatient? Does anyone else use VMM 2012 and find it slow?

    Read the article

  • Error: could not create the Java Virtual Machine. Error: A fatal exception has occurred. Program will exit

    - by Gleeson9
    Pre-note: This is not a problem I am having with Minecraft. All answers I can find seem to be Minecraft issues. Error: could not create the Java Virtual Machine. Error: A fatal exception has occurred. Program will exit. I get this error when I try to do something Java related. I cannot launch a .jar without this error coming up and when I try to install JDK, I get this error. This has been plauging me for a while and I was not able to research an answer so I thought I would ask it myself. EDIT: Windows 7 (x64) Dell Studio Laptop, 4GB RAM, external Radeon HD 6950 Graphics Card. I have tried uninstalling all JVMs and reinstalling but it didn't work, although I cannot remember how thorough I was so I may try again. Here is a list of all the Java related things I have installed (found in the uninstall or change programs window): Java 3D 1.5.1 Java 3D 1.5.1 (x64) Java 3D 1.5.2 Java 6 Update 30 Java 6 Update 30 (64-bit) Java 7 Update 2 Java 7 Update 3 (64-bit) JavaFX 2.0.3 (64-bit) JavaFX 2.0.3 SDK (64-bit)

    Read the article

  • How does one skip “Windows did not shut down successfully” in Win7-64?

    - by XenonofArcticus
    Migrating an app from an expensive and unreliable dedicated embedded x86 box running WinXP-embedded to COTS hardware (Dell E6410 laptop) running normal Win7-64. At this time, it's not feasible to deploy using Windows 7 embedded. The problem is, that the system is still sort of "embedded". The power could shut off at virtually any time without prior warning. We've stripped the OS down and removed the battery capability so that it will power down as desired. The app never writes to the disk, so it's not like we're going to corrupt anything terribly. The system is essentially idle after our app is up and running (with the exception of some computation, graphics, and TCP/IP and serial communications) so the OS enters a pretty stable state rather quickly. After a power-loss however, it rightly complains that Windows did not shut down successfully and presents the user with the Windows Error Recovery text screen. If left alone, it does eventually move on booting just fine, but we'd like to skip that step if possible. WinXP-embedded is designed to do this automatically, so I know it's possible. I've looked at the Kernel Switches but I didn't see anything documented for "Skip Windows Error Recovery". I've also read extensively on the startup process: http://homepage.ntlworld.com./jonathan.deboynepollard/FGA/windows-nt-6-boot-process.html I know I can disable the auto chkdsk in the registry, but that's not the same thing either. So, how do I streamline the boot process to not hassle the user about a situation that will be the regular normal situation?

    Read the article

  • RAID 6 that can read with least 1000 Mbit/s?

    - by Diblo Dk
    I purchased a Dell PERC 6/i which I expected to be able to read with 1000 Mbps. There is not much to do now, but there are some things I wanted knowledge about for another time. I have configured it with four 2 TByte drives and RAID 6. It have 256 MByt ram and transfer rate of 300 Mbps. The benchmark test showed: Min read rate: 136.3 Mbps Max read rate: 329,6 Mbps Avg read rate: 242,2 Mbps What could I had done to get at least 1000 Mbps? Is it normal for internal and external RAID controllers to have a lower transfer rate eg. 300 Mbps? (I did not noticed at the time that it was not 3 Gbps) How would a RAID 10 had performed compared to RAID 6 or 5? Would it have been better to use software RAID (Linux) with the internal 3 Gbps SATA controller? UPDATE: The drives is SATA III 6 Gbps. http://www.seagate.com/files/staticfiles/docs/pdf/datasheet/disc/desktop-hdd-data-sheet-ds1770-1-1212us.pdf (2TB)

    Read the article

  • Decrease in disk performance after partitioning and encryption, is this much of a drop normal?

    - by Biohazard
    I have a server that I only have remote access to. Earlier in the week I repartitioned the 2 disk raid as follows: Filesystem Size Used Avail Use% Mounted on /dev/mapper/sda1_crypt 363G 1.8G 343G 1% / tmpfs 2.0G 0 2.0G 0% /lib/init/rw udev 2.0G 140K 2.0G 1% /dev tmpfs 2.0G 0 2.0G 0% /dev/shm /dev/sda5 461M 26M 412M 6% /boot /dev/sda7 179G 8.6G 162G 6% /data The raid consists of 2 x 300gb SAS 15k disks. Prior to the changes I made, it was being used as a single unencrypted root parition and hdparm -t /dev/sda was giving readings around 240mb/s, which I still get if I do it now: /dev/sda: Timing buffered disk reads: 730 MB in 3.00 seconds = 243.06 MB/sec Since the repartition and encryption, I get the following on the separate partitions: Unencrypted /dev/sda7: /dev/sda7: Timing buffered disk reads: 540 MB in 3.00 seconds = 179.78 MB/sec Unencrypted /dev/sda5: /dev/sda5: Timing buffered disk reads: 476 MB in 2.55 seconds = 186.86 MB/sec Encrypted /dev/mapper/sda1_crypt: /dev/mapper/sda1_crypt: Timing buffered disk reads: 150 MB in 3.03 seconds = 49.54 MB/sec I expected a drop in performance on the encrypted partition, but not that much, but I didn't expect I would get a drop in performance on the other partitions at all. The other hardware in the server is: 2 x Quad Core Intel(R) Xeon(R) CPU E5405 @ 2.00GHz and 4gb RAM $ cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 32 Lun: 00 Vendor: DP Model: BACKPLANE Rev: 1.05 Type: Enclosure ANSI SCSI revision: 05 Host: scsi0 Channel: 02 Id: 00 Lun: 00 Vendor: DELL Model: PERC 6/i Rev: 1.11 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: CD-ROM GCR-8240N Rev: 1.10 Type: CD-ROM ANSI SCSI revision: 05 I'm guessing this means the server has a PERC 6/i RAID controller? The encryption was done with default settings during debian 6 installation. I can't recall the exact specifics and am not sure how I go about finding them? Thanks

    Read the article

  • Dead Linux server - need help and options

    - by Choi S.
    All, I have a Dell PE 1950 w/ 2 SATA drives in a software RAID1. OS is CentOS 5.5 (2.6.18.x). Starting this afternoon we received HW errors (something on the bus is bad, E171F) and the machine became unresponsive. We hard booted and it came back up for about 5 hours but then it happened again. I'm trying to figure out our options. Unfortunately we do not have similar hardware but I have a small desktop that I can use. I was contemplating putting one of the drives into the desktop and then starting it up. My goal was to then P2V it using Vmware converter but apparently the free v5.x doesn't support hot cloning/converting on a RAID volume, only the Enterprise 4.x version of Converter does. My questions are: 1.) Is putting a single drive out of a RAID1 pair into another piece of HW is safe? Based on my research and understanding it appears to be but would like confirmation. 2.) Is there any work around to the Vmware Converter not supporting RAID volumes during a hot clone/convert session? 3.) Are there other options I'm overlooking? Thanks in advance for reading and responding. --Choi S.

    Read the article

  • How do I find the cause for a huge difference in performance between two identical Ubuntu servers?

    - by the.duckman
    I am running two Dell R410 servers in the same rack of a data center. Both have the same hardware configuration, run Ubuntu 10.4, have the same packages installed and run the same Java web servers. No other load. One of them is 20-30% faster than the other, very consistently. I used dstat to figure out, if there are more context switches, IO, swapping or anything, but I see no reason for the difference. With the same workload, (no swapping, virtually no IO), the cpu usage and load is higher on one server. So the difference appears to be mainly CPU bound, but while a simple cpu benchmark using sysbench (with all other load turned off) did yield a difference, it was only 6%. So maybe it is not only CPU but also memory performance. I tried to figure out if the BIOS settings differ in some parameter, did a dump using dmidecode, but that yielded no difference. I compared /proc/cpuinfo, no difference. I compared the output of cpufreq-info, no difference. I am lost. What can I do, to figure out, what is going on?

    Read the article

  • Windows 7 breaks even in safe mode

    - by delenda
    Hi, I have a Dell XPS M1730 with Windows 7 installed. I noticed last night that after a few hours of use, the fans kicked into full and I couldn't do anything without it taking forever. Minimising windows, opening device manager or even opening process explorer took minutes and a game install I had just started took nearly 4 hours to complete. When procexp finally loaded, the refresh was so slow that it was mostly useless. From what I could gather, it was reporting 60% idle processes with procexp using nearly 40%. There were no hardware interrupts listed. When I rebooted, the problem went away for about 10 minutes and then the same thing happened. The issue persists in safe mode and even after I removed the graphics drivers, which have been an issue in the past, it still happens. Icons flash quite quickly on the desktop periodically and screen refresh is painfully slow. When booting now, the fans kick in to full as soon as the windows logon box comes up and it's taking 10 minutes to bring the desktop up. Chkdsk reports nothing and the raid check says that everything is fine. I'm thinking hardware failure, probably HDD but wanted some other opinions. I'm planning to try a linux live cd to see if it works without using the hard disks. If anyone has any input, it would be greatly appreciated. Delenda

    Read the article

  • Did my hard drive fail or is it something else?

    - by Julian
    Last night while I was watched a movie on my laptop the external monitor just went blank and the built-in display froze. Weird I thought, so I restarted it only to be greeted with this heart-breaking message. "No Operating System Found". After a few panicked restarts I accepted the fact that my hard drive might be done :(. Being the resourceful technie that I am, I whipped out Ubuntu Live on my old Flash Drive and was up and running before day break. I cannot access the hard drive through Ubuntu (which I expected) but I also cannot access my DVD drive either! This got me thinking that it might not be the hard drive and some other component that they hdd and the dvd uses. Hopefully this is the case. Which component is the most likely culprit? What tools can I use from Ubuntu Live on my USB flash drive to find out? I'm in a bad place without my hdd, thanks in advance for any assistance provided! P.S. My laptop makes a weird noise when I try to access or eject my DVD within the slot. Also my HDD makes a weird noise sometimes. Not sure how to describe it. System Specs: Dell 1558

    Read the article

  • Rescue system running TFS that BSODs, into vmware esxi

    - by 3molo
    Hi, After moving to new facilities, one of our old Dell servers running Windows Server 2003 R2 on PowerEdge 2650 HW BSODs with 0x8e. The server runs Team Foundation Server, so we have a few guys dependent on it. No one here knows TFS, so we have no idea how difficult it would be to setup from scratch. We have the MSSQL database(s) backed up, recent and fresh copy. Tried removing/refitting memory modules, but with no success. The system boots into safe mode but hangs occasionally. I booted a linux livecd and did a dd of both c: and d:, so I have all the data in compressed images on a vmware machine. For the guest, I created a 38G (actually it became 40GB) partition to act as C:, and booted a live cd. I then uncompressed the compressed disk image of c: and dd'd it to the new c: using 'gunzip -dc c.img.gz | dd of=/dev/sda1 bs=1M'. The operation ran for about 1000 seconds, and completed successfully. I assumed it would at least try to boot windows (but most likely BSOD due to not having correct drivers), but the Vmware ESXi guest does not seem to recognize it as a bootable disk. We don't have the vmware enterprise license, so the vmware converter cold cloning is not an option. Did I do something wrong in my dd's etc with the ISOs, or why would it not (try to) boot? Am I wasting my time? What other approach is there? Will continue to try to remove services and drivers to make the physical machine at least work reasonably well in safe mode. What do you suggest? 1. Continue to get the dd'd images to the virtual disk and get it to boot. 2. Install a new windows server, get team foundation server and restore from backup. 3. Focus on the old problematic hardware Any help appreciated

    Read the article

  • Ubuntu: Memory Leak

    - by Keener
    I'm having trouble finding from where this memory leak is occurring. I'm running Ubuntu 8.04 LTS on a Dell XPS M1530. I have 3GB of ram and I'm finding after about an hour or so of use top shows me 2GBs+ used. The strange thing is when I add up the memory percentages by PID either from top or ps aux I find that I should only be using about 20-25% of my available ram. What brought this to my attention was I've begun running vmware server again. Now, obviously the ram usage spikes when I load a virtual machine, but the memory VMware is using does not account for the memory usage I'm seeing via top or free. Stopping vmware server releases the memory which was allocated to it, but I'm still unable to find where this RAM is being used. After a complete reboot, of course, the memory is fine, but very quickly it climbs to 60-80% usage with the processes only appearing to account for a third of that. Any ideas where I should look for more information on what this could be?

    Read the article

  • Windows 8 Windows Store (Metro/ModernUI) applications not working (just show 'busy' animation or white screen)

    - by davidm_uk
    I have a Dell XPS 15 which shipped with Windows 7 x64, which I recently upgraded to Windows 8. The process went surprisingly smoothly (given that this was an upgrade, not a complete re-install), and the system generally seems very stable. However, today I noticed that several of the Windows Store apps don't work: they all behave in the same way, launching but then showing a spinning 'wait' animation indefinitely. This is affecting the standard Microsoft Mail, Store, Weather, News, Travel, Finance, Sport, Games and Music apps. The Bing app just shows a Bing logo on a coloured background (but no wait animation). The Calendar, Photos and SkyDrive apps open but then show a white screen. The Maps and Camera apps work without problems. The live tiles on the Start screen are updating correctly, for example the Mail app's tile shows a summary of new mail despite the Mail app's problems. All of these applications were working correctly a few days ago. I'm sure I've used several without problems since the last Windows update occurred on 7th November. Any suggestions on what might have happened and/or how to fix it would be very welcome. I don't need these Windows Store applications, but the fact that they're not working is irritating me.

    Read the article

< Previous Page | 93 94 95 96 97 98 99 100 101 102 103 104  | Next Page >