Search Results

Search found 7845 results on 314 pages for 'connected'.

Page 168/314 | < Previous Page | 164 165 166 167 168 169 170 171 172 173 174 175  | Next Page >

• Windows 7 MCE client server HTPC

  - by Dan Hook

  My HTPC is downstairs connected to my large screen. I would like to use my desktop upstairs to record over the air HDTV and stream it to the HTPC. I have Windows 7 Professional installed on the desktop. I currently have XP on the HTPC, but I'm going to upgrade it to Windows 7. Is there a particular flavor of Win 7 I should use? Is it possible to record on the desktop and use Windows MCE on the HTPC to watch the recorded content? What about live TV? The consensus I've seen is that Windows 7 cannot be configured as a Windows Media Center Extender. Is that the case? If so, what's the cheapest solution for an extender?

  Read the article

• suppress warnings from windows live mail untrusted cerficate ssl

  - by monkeyking

  Hi we have setup our own mailserver using ssl. Each time I start up windows live mail, in comes up with an annoying message that "The server you are connected to is using a security certificate that could not be verified" Is there some way to add this cerficate such that we wont see this message on every program start. When using firefox (our mailserver can also be webbased) or thunderbird, I get the option to allow the certificate without asking again. I'm perfectly aware that we can buy a certificate that will make the message go away, but this we dont want to do. Thanks edit: I have succesfully imported the certificate such that I can access the website without complains using ie, however the problem still persists in windows live mail.

  Read the article

• Connecting office to data center via Metro-ethernet

  - by Eric

  I am installing a metro ethernet link from my office to my data center. The office will have a cisco 3750 with several vlans. The data center end will have a more complicated set up. The metro e from the office will connect to a 2960, which will have two other 2960s with a few vlans and a 2811 router connected to it for connectivity to our other environments and the internet. I am looking at implementing this by connecting the office 3750 and the data center 2960 with a dot1q trunk and doing all routing at the 2811. I will configure subinterfaces for gateways for each of the vlans on the 2811. I work for a small company and don't have much of a budget for an ideal architecture. I can post a simple diagram if needed for clarification. Is there anything I am missing here? I feel like I am forgetting something very basic and want to make sure I eliminate any boneheaded mistakes.

  Read the article

• YUM and RPM crash due to the liblua-5.1 library being missing

  - by A troubled linux newbie.

  I've been playing around with a LiveUsb install of basic Fedora with persistence. I attempted to install moonscript, which requires Lua and LuaRocks. After installing Lua and discovering there were flaws in the install which prevented LuaRocks from working, I used rpm to force Lua off so I could use yum to re-install it. The result was an error of this sort being yielded by both rpm and yum: There was a problem importing one of the Python modules required to run yum. The error leading to this problem was: liblua-5.1.so: cannot open shared object file: No such file or directory I've concluded from this that my Lua version installed a library which both yum and rpm are now connected to. Is there anyway to fix this without reformatting my drive and installing everything from scratch?

  Read the article

• How can I share data from a Samsung Wave Mobile phone with the Mac OS?

  - by M. Bedi

  This is driving me up the wall just a bit. I have a new Samsung Wave mobile phone. It is running the Bada OS. The mobile phone does not come with anyone software for the Mac. The Kies desktop interface is only available for Windows. I did try installing the Kies software in a VM with Parallels 5 but it did not detect the phone connected via USB. I tried using Bluetooth file exchange on the Mac; it lets me browse the file system on the Wave phone but not actually see any of the media files; I just get empty directory views. But I am able to access files using media sharing with the Wave phone and my PS3. So what would be a Mac desks top app that can be used a media sharing browser?

  Read the article

• Why is my ftp connection timing out?

  - by NEPatriot

  This is the log info: Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is your current location Command: TYPE I Response: 200 TYPE is now 8-bit binary Command: PASV Response: 227 Entering Passive Mode (173,201,145,1,199,43) Command: MLSD Error: Connection timed out Error: Failed to retrieve directory listing The strange thing is that I've set the transfer mode to active... I've called my hosting company support and they're able to connect to this server using my ftp credentials. I've also tried to connect on another machine on my network and have the same issue. Could it be the firewall? My ISP?

  Read the article

• When can an FTP server close its passive connections?

  - by Don Kirkby

  Does the FTP protocol allow the server to close any of its passive connections while the client is still connected? Can it tell when the client is finished receiving and then close the connection? I'm including an FTP server in my application using the pyftpdlib Python project. I've got it to work in active and passive mode, but I'm a bit concerned about when it closes its passive connections. I've tried connecting to it with both FileZilla and the default ftp command in Ubuntu, and in both cases, I get a new passive port for every request. That is, if I sit in the root folder and type ls 10 times, I use up 10 ports. This means that I have to allocate a big block of passive ports for the FTP server to use so it won't run out. As soon as the client disconnects, the server releases all the passive connections associated with that client and those ports can be reused. However, a long-running connection could use up a lot of ports.

  Read the article

• ServerName no longer works as SQL Server 2008 Default instance name?

  - by TomK

  Folks, Somehow in struggling to install something (Sage MIP), I have unsettled my system's SQL Server 2008 instance names. If I fired up SSMS and connected to "MySystemName" (while logged into MySystemName), I used to immediately connect and could view my databases. Now if I connect to "(local)" or "." I connect just fine...but "MySystemName" gives me a timeout error. If I log in with "." and do "SELECT @@SERVERNAME" it comes back with "MySystemName" just fine. I've double checked that my network name is in the Security\Logins list, and it is, as a dbadmin. Any suggestions? I thought that having SQL Server 2005 Express might be a problem (the "battle of the default instances"), so I uninstalled that. No better.

  Read the article

• switch duplicates packets and forward in two route

  - by sami

  there is a network including a router, two hosts and a switch which connects hosts to router. i have a virtual machine on my system. the network adapter is set to act as bridge. so the virtual machine and real OS are my 2 hosts on different LAN. they use one network card and are connected to a switch. when each of host send a packet to the other one, the switch duplicate the packet and forward it to both router and the other host. how can I solve the duplicate packet problem? Thanks.

  Read the article

• Windows 7 "Could not reconnect all network drives" on boot

  - by Thermionix

  Windows 7 won't reconnect to my network drives on startup. Once it is done booting opening Windows Explorer and clicking each share will mount them. Windows 7 Enterprise N Service Pack 1 I have attempted formatting the windows machine - first thing done to machine was to map the network drives, upon reboot they were disconnected. It is running on an Crucial M4 64gb SSD. The host of the network shares is a Ubuntu-Server machine connected through a gigabit switch. A modem provides dhcp, although both these machines have static IP's defined. It won't reconnect the drives regardless of whether they're SAMBA shares or NFS shares - therefore I believe it's an issue with the windows machine. Ubuntu 11.10 (GNU/Linux 3.0.0-12-server x86_64) I've tried using ip address instead of netbios name for mapping shares on the windows machine, Also tried setting EnableLinkedConnections=1 gpedit.msc Computer Configuration - Administrative Templates - System-Logon - always wait for the network at computer startup and logon = yes

  Read the article

• Network? or router? problem

  - by Robert H Mercer

  I have two computers networked through a Netgear WG914 router which is connected to an Ipstar satellite modem via the RG47 LAN connector. The main computer is running Windows 7 Pro 64bit and the secondary computer is running Windows 7 Home Edition 32bit. On occasion there is a loss of internet connection usually on the main computer, often followed by a loss on the secondary comuter. Not, however, always the case. Windows troubleshooter, naturally, is about as much use as a politician in government.......NONE. There appears to be no problem with the ISP bad as it is and often the connection will be remade without any help from me. The difference in the OS's is not of any relevance since I had this problem before I changed over to Windows 7. Not being a nerd when it comes to networking I wonder if anyone has any constructive suggestions.

  Read the article

• Any experience with SATA SAS Interposer Cards?

  - by korkman

  Driven by the current price difference between SATA and SAS disks on one side and the potentially bad behaviour of SATA disks in bigger storage arrays on the other side, I have found so-called SATA-to-SAS interposer cards. Advertised as "seamlessly adding SAS capabilities to existing SATA disk drives", I wonder if anyone here has had some experience with these or similar products. The major benefits I can identify are the increased cable voltage (if all drives are SAS connected), the ability to power-cycle the drive and multipath (if desired). Obviously the SATA drive will still have to be RAID edition. The question is: Do these cards indeed increase the overall reliability of a storage system, or will failing SATA disks cause trouble nevertheless? Edit: I'm not asking for hypothetical answers, only actual experience please. I'm well aware that the typical 10k SAS drive is more reliable (and better performing) than 7200 SATA drives. But how does a nearline SAS, which is phyiscally the same disk as its SATA counterpart, compare to the SATA version with interposer?

  Read the article

• Migrate TFS 2010 Application Tier to another server on the same domain

  - by Liam

  I'm in the process of looking into the possibility of moving our TFS 2010 Application Tier to another server from the one it is on at the moment so that we can repurpose the hardware. I've been looking through the Microsoft Documentation over at http://msdn.microsoft.com/en-us/library/ms404869.aspx, but this assumes that everything is stored on one box (Application and Data tiers). In my setup however, our Data tier is separate to the Application tier and will be staying where it is. I think I should be able to do this but for my own peace of mind, would there be any issues or implications if I merely installed the Application Tier on the new hardware and then connected it to the existing data tier?

  Read the article

• How to fix unstable RJ45 jacks? [closed]

  - by BeemerGuy

  This is a little project I'm doing at home. I wanted to wire two rooms together (basically, the router is one room, and the switch is in the second room). So I ran a CAT5 between the two rooms, and wired an RJ45 jack in each room. I then hooked up the two jacks with two CAT5 cable to run it through the cable tester, and all 8 wires seem good. Now, when I connect the switch and the router, the connection is unstable -- I ping the router and it barely holds on for two pings before it disconnects, and stays in that unstable state. Just to make sure the router and the switch are ok, I connected them with long wire between the two rooms and the connection is absolutely stable, and pings continuously. What could be the cause for the unstable connection? Especially that it pings a few times, so there IS a connection. But why is it unstable? And how come the cable tester says it's ok, but it's unstable?

  Read the article

• DVI-D Splitter Not Working with GeForce 8400gs

  - by jimdrang

  I have a GeForce 8400gs and it has a DVI and VGA port on the back. I was using dual monitors with one VGA and one DVI cable. I wanted both displays to be digital so I bought a DVI-D splitter and put one DVI cable in each monitor, connected them to the splitter and put the single merged connection in the back of the cards DVI connection. It will not recognize the second monitor (I'm not even sure how it determined which one was the first monitor). The tech specs state that it supports "Two dual-link DVI outputs for digital flat panel display resolutions up to 2560x1600" http://www.nvidia.com/object/geforce_8400_tech_specs.html. Do I need a different converter or is my only option for dual monitors with this card one VGA, one DVI?

  Read the article

• Intel hybrid graphics stuck in power save mode

  - by OZZIE

  I have an Asus UL30V with Intel hybrid graphics. When I bought it it used to switch to turn of the better graphics card to save power and run on a more power effecient one. When I connected the laptop to a power source again I could go to the intel graphics icon on the task bar and click on "switch to enhanced performance mode" or something similar. But like 2-3 months ago it suddenly vanished. I cannot switch modes anymore, it's gotten stuck in power save mode. I can change the windows power setting but that doesn't enable the better graphics card :( What should I do? I've tried restarting the computer and that does not work. I really hope I don't have to reinstall the drivers! It seems like other people have had the same issue: http://en.community.dell.com/support-forums/laptop/f/3518/p/19422695/19994601.aspx , he hasn't even got the same computer as me. I have windows 7 Home Premium x64 Any ideas?

  Read the article

• CPanel: Every url is being redirected to http://:2083

  - by Frank

  On my cpanel server, I restored about 50 accounts from crashed cpanel server. All of the sites were working fine, but suddenly without changing anything, every site started to get redirected to url "http://:2083/"., There is nothing in logs, no errors. when i do wget it says: wget grinfeld.com.br --2012-09-04 13:18:23-- http://grinfeld.com.br/ Resolving grinfeld.com.br... 198.101.221.254 Connecting to grinfeld.com.br|198.101.221.254|:80... connected. HTTP request sent, awaiting response... 301 Moved Location: https://:2083/ [following] https://:2083/: Invalid host name.

  Read the article

• ubuntu 12.04 - keep getting "Server not found" for some websites

  - by android developer

  ever since last week , i've noticed that many websites cannot be accessed , and it doesn't matter if i use firefox or chromium as a web browser . as an example of such a website is: http://tutorials-android.blogspot.co.il/2011/05/layout-animation-in-android.html all i get is a "Server not found" error page . sometimes after a few refreshes it works just fine . i've checked it on a windows OS machine that is connected to the exact same LAN network , and the website is shown just fine . i've also checked the /etc/hosts file and it doesn't contain anything suspicious . what is going on? how can i fix it?

  Read the article

• Enable/disable wireless interface in a bat file

  - by Herms

  Is there a way to enable/disable a wireless network interface via the command line (so I can put it in a bat file)? When I'm in the office I use a wired connection, but Windows still occasionally bugs me about my wireless connection not being connected (even though I turned off the option for notifying me when there's no connectivity). I'm guessing the only way to stop it from bugging me is to disable the interface, but I'd rather not have to go into the network settings every time I need to do so. I'd like to set up a bat file or a shortcut that I can use to enable/disable the wireless (preferably a single one that toggles the current state), and then just set up a keyboard shortcut for that. I just have no idea how to do so from the command line.

  Read the article

• Can a custom DPI setting be applied to Remote Desktop sessions?

  - by sejong

  Can a custom DPI setting be applied to Remote Desktop sessions? When you try to change the DPI from a Remote Desktop session, you get a message that display settings can't be changed from a remote session. That made me think that changing DPI from a console setting would work. It did, sort of. If I connected via Remote Desktop to an existing console session with a custom DPI setting, that setting would be applied to the Remote Desktop session. However, if I logged off that session, the custom DPI would not be applied to subsequent Remote Desktop sessions even though it was maintained for subsequent console sessions. It looks like the registry value HKEY_CURRENT_USER\Control Panel\Desktop\WindowMetrics\AppliedDPI (and perhaps other values) is overwritten at logon, but I haven't been able figure out how to prevent it.

  Read the article

• Connecting via ShrewSoft VPN client means no LAN internet access (Windows 7 64 bit) - any advice please?

  - by iwishiknewmoreaboutnetworking

  I have a Windows 7 64 bit desktop machine which is connected to a LAN. I recently installed ShrewSoft VPN client v 2.1.7 on my machine so that I can connect to a license server hosted by my customer. They are running a Cisco VPN server and I originally tried (unsuccessfully!) to use the Cisco VPN client for Windows 64 bit but the default gateway wasn't being configured correctly after loading in my pcf file. Using ShrewSoft I am able to import the same pcf file, and successfully connect to the machine I need to using the VPN client software. The client machine I need to connect to has IP address 1.52.90.33. The problem is that when I am connected to the customer network using the VPN client application (and after a few minutes) I lose my LAN internet connection. I can only presume that this is because, by default the ShrewSoft VPN client application automatically tunnels all traffic through the VPN connection. I know there is an option to switch off the "Tunnel All" option on the Policy tab of the application and enter a Remote Network Resource (to "Include" or "Exclude") as "Address" and "Netmask" IP addresses however I am not sure what I need to enter here. Here is my ipconfig output before connecting to the VPN (with suffixes blanked out): Windows IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : ***.*** Link-local IPv6 Address . . . . . : fe80::8de3:9dbe:393a:33ba%11 IPv4 Address. . . . . . . . . . . : 150.237.13.17 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 150.237.13.1 Tunnel adapter 6TO4 Adapter: Connection-specific DNS Suffix . : ***.*** IPv6 Address. . . . . . . . . . . : 2002:96ed:d11::96ed:d11 Default Gateway . . . . . . . . . : 2002:c058:6301::c058:6301 Tunnel adapter Local Area Connection* 9: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:2cf9:38c4:6912:f2ee Link-local IPv6 Address . . . . . : fe80::2cf9:38c4:6912:f2ee%12 Default Gateway . . . . . . . . . : Tunnel adapter isatap.***.***: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : ***.*** Here is my route print output before connecting to the VPN: =========================================================================== Interface List 11...20 cf 30 9d ec 2a ......Realtek RTL8168D/8111D Family PCI-E Gigabit Ethern et NIC (NDIS 6.20) 1...........................Software Loopback Interface 1 14...00 00 00 00 00 00 00 e0 Microsoft 6to4 Adapter 12...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 13...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 150.237.13.1 150.237.13.17 2 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 150.237.13.0 255.255.255.0 On-link 150.237.13.17 257 150.237.13.17 255.255.255.255 On-link 150.237.13.17 257 150.237.13.255 255.255.255.255 On-link 150.237.13.17 257 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 150.237.13.17 257 255.255.255.255 255.255.255.255 On-link 12

  Read the article

• Connect two devices with ethernet

  - by mofle

  I have a MacBook Pro and I'm going to buy a Boxee Box. I have access to wireless internet, but it's slow and out of my control. So my question is, what is the best way for both devices to get internet access, and the Boxee Box to get SMB access to the Mac, when only the Mac is connected to the wireless internet? I'm thinking an ethernet cable from the Boxee Box to my Mac, and connection sharing on my Mac. Can you explain the setup, is there any configuring.

  Read the article

• How do I prevent internet access to a group of computers on my network?

  - by Kevin Boyd

  Well I have the following setup... Computer A , B and C are networked.... Computer A is connected to the internet, computer B and C are not setup for internet access currently but I guess its possible with some kind of setting they would eventually be able to access the internet and this is what I would like to prevent. In summary only A should have internet access while A and B and C should still be on intranet. Is this kind of config possible?, what kind of software or setup or tools would I need to achive this?

  Read the article

• Mini DV and DVI Conversion

  - by Kairan

  Video card is: AMD HD 6950 My video card comes with 1xHDMI, 2xDVI, and 2xMini DV ports. I have always used VGA and DVI only. I have the HDMI already connected. I want to hook up 2 more display. One of the display can take a VGA only, the other is an LCD TV so it has VGA, HDMI, Component. I am wondering: 1) What is the best output port to use for the second two monitors? The miniDV or the DVI? 2) I need to run a long cable maybe 15-25 feet, this might change the answer to question 1, is an HDMI long cable 20+ ft going to be better than a 20ft DVI or miniDV ?

  Read the article

• internet speed and routers are controlled by whom

  - by Ozgun Sunal

  i need to learn two things. each is related to other a bit. The first one is, while our LAN speed is usually 100 Mbps or at gigabit levels(very big compared to WAN speeds), WAN speed for instance DSL connections are far less than this. However, we are able to download huge files at those Mb speeds. Isn't this weird? [my real concern is why WAN speed is lower than LAN speeds] Who controls those routers around the large Internet? (while we, as web clients are connected to Internet, packets travel through those routers to the destination network/s).But, are those routers all inside the ISP network and if not, who controls those large numbers of routers?

  Read the article

< Previous Page | 164 165 166 167 168 169 170 171 172 173 174 175  | Next Page >